JB/T 8947-2008Rubber belts for fixed chamber belt vacuum filters (English PDF)
固定室带式真空过滤机用橡胶滤带
This is a limited preview
Buy now to download the full PDF (15 pages)
Need quotation for your management?
Get a formal quotation for JB/T 8947-2008 in 30 minutes.
Issued by
MIIT
Level / Type
Industry · Recommended
Issue date
June 4, 2008
Implementation date
November 1, 2008
Scope
JB/T 8947-2008 is the English-translated version of 固定室带式真空过滤机用橡胶滤带.
JB/T 8947-2008 is the Chinese standard "Belt for rubber belt filter".
Its scope clause reads: This standard specifies the requirements for rubber filter belts with rubber covers used in fixed-chamber belt vacuum filters, covering aspects such as types, basic parameters, technical requirements, test methods, inspection rules, marking, packaging, transportation, storage.
This standard is applicable to rubber filter belts used in fixed-chamber belt vacuum filters (hereinafter referred to as "filter belts"). Its clauses include terms and definitions; types and basic parameters; technical requirements; test methods; inspection rules; marking, packaging, transport, storage.
It was issued by the National Development and Reform Commission on JUNE 04, 2008 and took effect on NOVEMBER 01, 2008.
Found what you need?
Document preview — JB/T 8947-2008
National Standard of the People's Republic of China
- Replacing
- JB/T 8947-1999
Issued by: Ministry of Industry and Information Technology of the People's Republic of China
Contents
- Foreword3
- 1 Scope4
- 2 Normative references4
- 3 Terms and definitions5
- 4 Types and basic parameters6
- 4.1 Types6
- 4.2 Basic parameters7
- 4.3 Model designation method9
- 5 Technical requirements10
- 5.1 Physical and mechanical properties10
- 5.2 Dimensional tolerances12
- 5.3 Appearance quality13
- 6 Test methods14
- 7 Inspection rules14
- 8 Marking, packaging, transport, storage15
- 8.1 Marking15
- 8.2 Packaging, transport, storage15
1 Scope
This standard specifies the requirements for rubber filter belts with rubber covers used in fixed-chamber belt vacuum filters, covering aspects such as types, basic parameters, technical requirements, test methods, inspection rules, marking, packaging, transportation, storage.
This standard is applicable to rubber filter belts used in fixed-chamber belt vacuum filters (hereinafter referred to as "filter belts").
2 Normative references
The provisions in following documents become the provisions of this Standard through reference in this Standard. For the dated references, the subsequent amendments (excluding corrections) or revisions do not apply to this Standard; however, parties who reach an agreement based on this Standard are encouraged to study if the latest versions of these documents are applicable. For undated references, the latest edition of the referenced document applies.
GB/T 528 Rubber, vulcanized or thermoplastic - Determination of tensile stress-strain properties (GB/T 528-1998, eqv ISO 37:1994)
GB/T 531 Rubber - Determination of indentation hardness by means of pocket hardness meters (GB/T 531-1999, idt ISO 7619:1986)
GB/T 1689 Rubber vulcanized - Determination of abrasion resistance (Akron machine) (GB/T 1689-1998, neq
BS 903. Part Aq.1988)
GB/T 1690 Rubber, vulcanized or thermoplastic - Determination of the effect of liquids (GB/T 1690-2006, ISO 1817:2005, MOD)
GB/T 3512 Rubber, vulcanized or thermoplastic - Accelerated ageing and heat resistance tests - Air-oven method (GB/T 3512-2001, eqv ISO 188:1998)
GB/T 3690-1994 Conveyor belts of textile carcass - Test method for tensile strength and elongation (eqv ISO 283:1990)
GB/T 4490 Conveyor belts - Dimensions (GB/T 4490-1994, eqv ISO 251:1987)
GB/T 5752 Conveyor belts - Marking (GB/T 5752-2002, eqv ISO 443:1991)
GB/T 6759-2002 Textile conveyor belts - Adhesive strength between constitutive elements - Test methods (ISO 252-1:1999, IDT)
GB/T 9867 Rubber, vulcanized or thermoplastic - Determination of abrasion resistance using a rotating cylindrical drum device (GB/T 9867-2008, ISO 4649:2002, IDT)
HG/T 3056 Conveyor belts - Guidelines for storage and handling (HG/T 3056-2006, ISO 5285:2004, IDT)
3 Terms and definitions
The following terms and definitions apply to this standard.
3.1 Effective width
The width of the portion of the filter belt involved in filtration.
3.2 Discharge hole
A hole in the filter belt used for discharging filtrate.
3.3 Nominal width
The total width of the filter belt (i.e., the design width of the filter belt).
3.4 Capped edge
A rubber component, which is bonded to the edge of the filter belt, used to prevent the filtration material from spilling over.
3.5 Straightness
When the filter belt is laid out flat on a level surface, select any two points on the same side of the belt edge with a distance between them greater than 1/3 of the belt length, the maximum distance from the straight line connecting these two points to the belt edge constitutes the straightness of the filter belt.
3.6 Inside perimeter
The length of the non-working side of the filter belt after it has been spliced into a loop (i.e., the design length).
3.7 Tensile strength of whole thickness
In a tensile test performed on a full-thickness specimen of the filter belt, the ratio -- of the force required to break the specimen to the original width of the specimen.
3.8 Reference force
The force obtained by multiplying 10% of the nominal full-thickness longitudinal tensile strength of the filter belt by the basic value of the width at the center of the specimen.
3.9 Elongation at reference force
In a tensile test, the elongation of the specimen when subjected to the reference force.
3.10 Thickness
The height of a single layer of the filter belt when placed horizontally (excluding the capped edges).
4 Types and basic parameters
4.1 Types
4.1.1 Ordinary structure
This structure consists of a specific number of layers of reinforcement material, laminated together to form an integral belt core (reinforcement layer). The belt core is sandwiched between upper and lower rubber cover layers, forming a continuous loop.
The upper cover surface features regularly spaced transverse drainage grooves; capped edges may be installed on both edges as required (see Figure 1).
4.1.2 Pure rubber structure
This refers to a variant of the standard structure in which a layer of pure rubber, exceeding 10 mm in thickness, is situated between the drainage holes and the reinforcement layer, ensuring that the reinforcement layer is not exposed within the drainage holes (see Figure 2).
4.1.3 Special structure
This refers to types other than the two structures described above, characterized by specific requirements in their structural design. For example, a structure featuring reinforced guide ribs (see Figure 3).
4.2 Basic parameters
The basic parameters of the filter belt shall comply with the specifications listed in Table 1. […]
......
This preview omits tables, figures, formulas and parts of the technical clauses. The complete document — 15 pages — is available in the English PDF.
Referenced standards
Normative references
- GB/T 528Rubber, vulcanized or thermoplastic -- Determination of tensile stress-strain properties
- GB/T 531Rubber--Determination of indentation hardness by means of pocket hardness meters
- GB/T 1689Rubber vulcanized-Determination of abrasion resistance (Akron machine)
- GB/T 1690Rubber, vulcanized or thermoplastic—Determination of the effect of liquids
- GB/T 3512Rubber, vulcanized or thermoplastic - Accelerated ageing and heat resistance tests in hot air
- GB/T 3690-1994Textile conveyor belts - Full thickness tensile strength, elongation at break and elongation at the reference load - Test method
BS 903
Similar standards
Editions of JB/T 8947
| Edition | Title | Revision | Status |
|---|---|---|---|
| JB/T 8947-2008 | Rubber belts for fixed chamber belt vacuum filters | current edition | Current |
| JB/T 8947-1999 | Rubber belts for fixed chamber belt vacuum filters | previous edition | Superseded |
This page sells the current edition, JB/T 8947-2008. Earlier editions are listed for reference only.
How to Download JB/T 8947-2008
- 1
Add to cart
Click "Download PDF" on this page and choose "Buy this standard". You can add more standards before checkout.
- 2
Checkout
Enter your email and billing details. Payment is processed securely by Stripe (cards or bank transfer). Prefer bank details? Request a quotation (min. order $300).
- 3
Fast delivery
After payment you'll receive an email confirmation. The English PDF is sent to the same address, usually within minutes and at the latest within 1 business day.
- 4
Invoice included
A tax invoice is attached to the confirmation email. Need a custom invoice? Contact us.
Related Standards
GB/T 1689-1998 — Rubber vulcanized--Determination of abrasion resistance (Akron machine)
GB/T 1689-2014 — Rubber vulcanized-Determination of abrasion resistance (Akron machine)
GB/T 1690-1992 — Rubber, vulcanized-Determination of the effect of liquids
JB/T 8947-2008
$135.00