GB/Z 32075-2015Non-destructive testing - Discontinuities in specimens for use in qualification examinations (English PDF)
无损检测 资格鉴定考试用试样中的不连续
This is a limited preview
Buy now to download the full PDF (15 pages)
Need quotation for your management?
Get a formal quotation for GB/Z 32075-2015 in 30 minutes.
Issued by
SAMR; SAC
Level / Type
National · Recommended
Issue date
October 9, 2015
Implementation date
October 9, 2015
Scope
GB/Z 32075-2015 is the English-translated version of 无损检测 资格鉴定考试用试样中的不连续.
GB/Z 32075-2015 is a Chinese national guidance document, identical to ISO/TS 22809:2007, on the discontinuities that specimens for non-destructive testing qualification examinations must contain.
It covers the specimens and how many a centre needs, product categories, minimum discontinuity sizes, surface condition, the number of discontinuities, specimens for radiographic film interpretation and the reference test report.
Informative annexes list typical discontinuities in castings, welds, wrought products, forgings, tubes and pipes, and in in-service testing. Acoustic emission, infrared thermography, strain testing and leak testing need no specified discontinuity types because of their special conditions.
Examination centres qualifying personnel under GB/T 9445 use it to build representative specimens. It was issued on 9 October 2015.
Found what you need?
Document preview — GB/Z 32075-2015
National Standard of the People's Republic of China
- ICS
- 03.100.30; 19.100
- Classification
- J 04
Issued by: State Administration for Market Regulation; Standardization Administration of the PRC
Contents
- Preface
- 1 Scope
- 2 Normative references
- 3 Terms and definitions
- 4 Sample
- 5 product categories
- 6 discontinuous minimum size
- 7 surface conditions
- 9 radiographic interpretation of the interpretation of the actual operation of the test (negative)
- 10 standard test report
- Appendix A (Informative) Discontinuity of castings
- Appendix B (informative) discontinuity of welded parts
- Appendix C (Informative) non-continuous rolling pieces
- Appendix D (Informative) non-continuous rolling forgings
- Appendix E (Informative) Pipe and pipe discontinuities
- Appendix F (Informative) In-service testing discontinuities
Foreword
This instructional document has been drafted in accordance with the rules given in GB/T 1.1-2009.
This guideline uses the translation method identical with ISO /T S22809.2007 "Non Destructive Testing Qualification Examination Discontinuous ".
Our document, which corresponds in a consistent manner to the international documents that are normative references in this Guidance Document, is as follows.
--- GB/T 5185-2005 Welding and related process code (ISO 4063:1998, IDT);
GB/T 6417.1-2005 Metallic welded joints imperfection classification and description (ISO 6520-1:1998, IDT).
1 Scope
This Guidance Document specifies the types of discontinuities in test specimens for non-destructive testing.
Acoustic emission detection, infrared thermal imaging detection, strain detection and leak detection do not have to specify the type of discontinuities because of their special conditions (Such as AT with artificial sound source instead).
2 Normative references
The following documents for the application of this document is essential. For dated references, only the dated version applies to this document. For undated references, the latest edition (including all amendments) applies to this document.
GB/T 9445-2008 non-destructive testing personnel qualification and certification (ISO 9712:2005, IDT)
ISO 4063 Welding and related process technology and code name (Weldingandaliedprocesses-Nomenclatureof processesandreferencenumbers)
ISO 6520-1 Welding and related processes - Classification of geometric imperfections in metallic materials - Part 1. Welding andalied processes-Classificationofgeometricimperfectionsinmetalicmaterials-Part 1: Fusionwelding)
3 Terms and definitions
GB/T 9445-2008 defined and the following terms and definitions apply to this document.
3.1 Test area
Practical examination, the applicant in the entire sample or part of the implementation of the test area.
Note: A sample can contain several non-overlapping detection areas.
4 Sample
The minimum number of samples for any test center is nmin, calculated from the following formula.
The minimum number of specimens.nmin = nsp × ncmax In the formula. nsp --- practice test, the number of samples for each candidate; ncmax --- The maximum number of people who are allowed to take practical exams simultaneously.
5 Product categories
5.1 Overview
Specimens should be specific to a class that simulates the actual geometry and contains the typical discontinuities that are formed during manufacture or in service Some discontinuous, manufacturing process and in-service use of the formation of discontinuities). Discontinuities can be natural, artificial or transplanted.
......
This preview omits tables, figures, formulas and parts of the technical clauses. The complete document — 15 pages — is available in the English PDF.
Referenced standards
Normative references
ISO 4063 · ISO 6520-1
Similar standards
How to Download GB/Z 32075-2015
- 1
Add to cart
Click "Download PDF" on this page and choose "Buy this standard". You can add more standards before checkout.
- 2
Checkout
Enter your email and billing details. Payment is processed securely by Stripe (cards or bank transfer). Prefer bank details? Request a quotation (min. order $300).
- 3
Fast delivery
After payment you'll receive an email confirmation. The English PDF is sent to the same address, usually within minutes and at the latest within 1 business day.
- 4
Invoice included
A tax invoice is attached to the confirmation email. Need a custom invoice? Contact us.
Related Standards
GB/T 9445-2008 — Non-destructive testing - Qualification and certification of personnel
GB/Z 102.17-2026 — Semiconductor devices - Discrete devices - Part 17: Magnetic and capacitive coupler for basic and reinforced insulation
GB/Z 103-2026 — Health informatics - The architecture of internet healthcare service network
GB/Z 32075-2015
$205.00