GB/Z 26854-2011Standardising the characteristics of electricity (English PDF)
电特性的标准化
This is a limited preview
Buy now to download the full PDF (17 pages)
Need quotation for your management?
Get a formal quotation for GB/Z 26854-2011 in 30 minutes.
Issued by
SAMR; SAC
Level / Type
National · Recommended
Issue date
July 29, 2011
Implementation date
July 29, 2011
Scope
GB/Z 26854-2011 is the English-translated version of 电特性的标准化.
GB/Z 26854-2011 is a guiding technical document, not a mandatory standard, on how the quality of electricity supplied as a commodity should be described. It is an identical adoption of IEC/TR 62510-2008 and is intended to guide standardization work on power quality.
The document explains the link between power quality and electromagnetic compatibility, sets out the responsibilities of the parties involved in power quality problems, and treats standardized network impedance as a basic analysis route, citing the 16 A and 75 A supply provisions of IEC 60725.
The phenomena it reviews include continuity of supply, control of voltage and frequency, harmonics and interharmonics, components between 2 kHz and 9 kHz, flicker, short-duration rms variations, transient and power-frequency overvoltages, and three-phase unbalance. It applies to AC 50 Hz supply systems. It was issued on 29 July 2011.
Found what you need?
Document preview — GB/Z 26854-2011
National Standard of the People's Republic of China
- ICS
- 29.020
- Classification
- K 04
Issued by: State Administration for Market Regulation; Standardization Administration of the PRC
Contents
- Foreword
- Introduction
- 1 Scope
- 2 Power quality phenomenon
Foreword
The report was released by the IEC /TC8 committee.
This instructional document has been drafted in accordance with the rules given in GB/T 1.1-2009.
Introduction
Currently, different countries have some characteristic standards for utility grid power supply, IEC 61000-2-1:1990, EN 50160 and IEEE1159 Standards such as trying to cover all the features. According to the European Directive on Defective Products (85/374/EEC), EN 50160 has formally introduced electric energy Treat as a product.
It is the grid operator's responsibility to design and operate the grid in accordance with national laws, national or international standards so that the power quality meets the requirements.
The following describes the electrical performance, as well as the relationship between power quality and electromagnetic compatibility (EMC). Most of its content from Europe Europe Power Quality Report (EURELECTRICPQReport, 2nd Edition).
Power quality Electricity supply is one of the most basic services of all basic services on which modern society depends. To this end, its important quality characteristics of the main To show in the following areas.
a) Continuity of power supply, including.
- In order to ensure a continuous supply of electricity on a day-to-day basis, operational mechanisms are needed to prevent long or frequent disruptions to the supply.
- In order to ensure the safety of medium and long term power supply, the requirements on the user needs and power generation, transmission, distribution and other equipment and a variety of power availability There is a steady balance between.
b) The standardization of supply voltage and frequency is necessary for the generation, transmission, distribution and utilization of electrical equipment. Will supply voltage and Frequency control within the reasonable range of the nominal value used is very important.
c) Although the voltage and frequency are generally maintained at an acceptable level, there are some fairly short, low amplitude or sporadic in actual operation The amount of irregular superimposed on the voltage, interfere with the user's electrical equipment or electrical equipment in the power grid to play its normal function.
Note: There are many different ways to classify the quality of power supplies, and the classification by function from current generation, supply and grid operations is more complicated.
For example, the following term was used in a recent report submitted by The Council of European Electricity Regulator.
--- Business Quality. A variety of quality of service between suppliers and users (services here, not limited to grid operations);
--- Continuity of power supply. The extent to which the user perceives the power supply interruption due to various reasons (see a) above);
--- Voltage quality. Voltage technical characteristics of the user-powered indicators, such as amplitude and frequency (see b) above) and potential disturbance problems (see above c)).
1 Scope
This guidance document summarizes the quality of electrical energy as a description of the method; described the relationship between power quality and electromagnetic compatibility;
Clarified the responsibilities and obligations of the stakeholders involved in power quality issues.
This Guidance Document is used to guide the standardization of power quality.
This guideline is applicable to AC 50Hz power supply system.
2 Power quality phenomenon
Analysis of power quality problems by standardizing network impedance characteristics is a fundamental method, such as the 16A and 75A in IEC 60725 Electrical equipment supply regulations. So that power suppliers, distributors and system users can share power quality responsibilities.
NOTE Many countries do not always adopt standardized network impedances because of the special grid architecture that uses other approaches to make power quality management even more Convenient and more reasonable.
The degree of economic development has a great impact on the importance of various indicators of power quality. The main concern in the early days was the electrical energy actually Availability; then concerned about the voltage and frequency in most of the power supply time is within the reasonable range of its nominal value, this stage is not yet obvious Concerned about voltage sags, transients and other effects; but with the high degree of economic development, in addition to supply continuity, voltage and frequency, a series of As the beginning to get the attention, with the modern term "power quality" to be summarized.
Power quality phenomenon is briefly described below.
- Harmonic, inter-harmonic, 2kHz ~ 9kHz range of frequency components.
These components are mainly caused by the electrical equipment in the system, the electrical characteristics of such equipment as current is nonlinear with respect to the voltage Department, in addition to absorbing fundamental current, but also to the power supply network injection of non-fundamental frequency current.
Note: Harmonic. The frequency is an integer multiple of the fundamental frequency.
Between the harmonic frequency of the power frequency voltage and current, that is, the actual frequency is not an integral multiple of the fundamental frequency. Inter harmonics can be discrete frequencies Rate or in the form of a broadband spectrum. By the inverter inverter, rectifier or similar non-linear load control equipment operation produce.
- Flicker, the main effect of voltage fluctuations.
The amplitude of the current absorbed by some powered devices has a fluctuating characteristic, which causes the grid voltage to fluctuate accordingly.
- Short-term rms changes (instantaneous, temporary and short-term).
Caused by unexpected events, system shorts and cutouts, motor starts, sudden increases in current in the power supply system or connected devices, and more.
- Transient over-voltage (surge and oscillation over-voltage).
A number of electromagnetic phenomena, including switching operations, blown fuses, lightning strikes on the grid, etc., are produced on the distribution network and its connected equipment Health transient over-voltage.
- Short-term power frequency overvoltage and low voltage (long rms changes).
According to practice, short-term power overvoltages between live conductors (phase conductors) and ground are often caused by the breaking of the neutral (wire) conductor. Short time Power line overvoltages may also occur during a utility distribution or customer premises equipment ground fault and disappear when the ground fault is cleared.
- unbalanced.
The imbalance voltage of the three-phase system is caused by the system failure or the imbalance of phase current absorbed by the system's electrical equipment.
......
This preview omits tables, figures, formulas and parts of the technical clauses. The complete document — 17 pages — is available in the English PDF.
Referenced standards
Normative references
IEC 60725
Similar standards
How to Download GB/Z 26854-2011
- 1
Add to cart
Click "Download PDF" on this page and choose "Buy this standard". You can add more standards before checkout.
- 2
Checkout
Enter your email and billing details. Payment is processed securely by Stripe (cards or bank transfer). Prefer bank details? Request a quotation (min. order $300).
- 3
Fast delivery
After payment you'll receive an email confirmation. The English PDF is sent to the same address, usually within minutes and at the latest within 1 business day.
- 4
Invoice included
A tax invoice is attached to the confirmation email. Need a custom invoice? Contact us.
Related Standards
GB/Z 102.17-2026 — Semiconductor devices - Discrete devices - Part 17: Magnetic and capacitive coupler for basic and reinforced insulation
GB/Z 103-2026 — Health informatics - The architecture of internet healthcare service network
GB/Z 108-2026 — Health informatics - Internet healthcare service pattern
GB/Z 26854-2011
$145.00