GB/Z 25756-2010Vacuum technology - Bakable flanges - Dimensions of knife-edge flanges (English PDF)
真空技术 可烘烤法兰 刀口法兰尺寸
This is a limited preview
Buy now to download the full PDF (15 pages)
Need quotation for your management?
Get a formal quotation for GB/Z 25756-2010 in 30 minutes.
Issued by
SAMR; SAC
Level / Type
National · Recommended
Issue date
December 23, 2010
Implementation date
December 23, 2010
Scope
GB/Z 25756-2010 is the English-translated version of 真空技术 可烘烤法兰 刀口法兰尺寸.
GB/Z 25756-2010 is a Chinese national guidance document, identical to ISO/TS 3669-2:2007, that fixes the dimensions of bakable knife-edge flanges for vacuum systems.
It covers fixed and rotatable bolted flanges of the knife-edge type, the metal-sealed design that grew out of the CF flange, for use from atmospheric pressure down to 10^-13 Pa.
The text defines the knife-edge style flange, the nominal bore and the leak check groove, and lists symbols for the bolt hole, bolt circle, seal groove, knife-edge and gasket diameters, with dimension tables in millimetres and inches.
The Chinese edition adds an enlarged view of the knife-edge detail. Designers of high and ultra-high vacuum equipment use it to keep flanges from different makers interchangeable. It was issued on 23 December 2010.
Found what you need?
Document preview — GB/Z 25756-2010
National Standard of the People's Republic of China
- ICS
- 23.160
- Classification
- J 78
Issued by: State Administration for Market Regulation; Standardization Administration of the PRC
Contents
- Foreword
- Introduction
- 1 Scope
- 2 Terms and definitions
- 3 Symbol
Foreword
GB /Z 25756 Equivalent to ISO /T S3669-2.2007 "Vacuum technology bake flange Part 2. Blade flange size" (English version).
For ease of use, the following technical editorial changes have been made in this Guidance Document.
--- Removed the foreword and introduction of international standards, added the introduction of this technical guidance document;
--- Use the decimal symbol "." Instead of as a decimal point comma ",";
--- In the "Figure 2 knife detail" added a knife edge enlarged view of the map clearer and more intuitive;
--- With the standard series of our standard range of dimensions marked "2 ° ~ 40 °" instead of "Figure 2 blade detail" in the 40 ° 2 ° blade angle size; "4.0 ~ 4.0" instead of "4.01.5 slot size recommended size" in Figure 4 slot width size;
--- Unit 1 in Table 1 "mm (in)" unified written in the upper right corner of the table as "units are millimeters (inches)";
--- Table 2 in the unit "mm" unified written in the upper right corner of the table as "millimeters."
This Guidance Document is governed by the National Vacuum Technology Standardization Technical Committee (SAC/TC18).
Introduction
In actual use, bake flange flanges have become an important part of vacuum system components. For a long time ISO / TC112 has been trying to develop "vacuum technology can be baked flange knife flange size" standard. After the efforts of member states, ISO / TS3669-2:2007 "Vacuum technology bake flange Part 2. Blade flange size" has finally been published.
To avoid confusion and help standard users understand the standard case, we provide some relevant information for illustration.
ISO 3669 consists of two parts.
--- ISO 3669:1986 "vacuum technology can be baked flange size";
--- ISO /T S3669-2.2007 "Vacuum technology bake flange Part 2. Blade flange size." ISO /T S3669-2.2007 compared with ISO 3669:1986 made important technical changes, ISO 3669:1986 provides for two lines Column of baking flanges.
--- Preferred series, the main dimensions to ensure compatibility with standardized non-toasted flanges (see ISO 1609);
--- Secondary election series, corresponding to the common flange.
ISO /T S3669-2.2007 defines only one series and no longer depends on the value of the "preferred" series. In fact, ISO 3669.
The 1986 "Preferred" series is outdated or obsolete, thus enhancing the "second choice" series to become one and the only set of prescribed sizes. another In addition, several dimensions of this "second choice" series were also modified for general use of the flange until the detailed dimensions of the blade seal profile were Included.
ISO /T S3669-2.2007 will be reviewed by ISO /TC112 after three years in order to decide whether to be within the next three years Approved, revised to international standards, or withdrawn. If approved, it will be revised again in the next three years, During this period, it must either be turned into an international standard or be withdrawn.
The above description of ISO 3669 consists in his connection to GB/T 16709.1-2010/ISO 9803-1:2007 "Vacuum Technology Pipe Fittings Assembly dimensions - Part 1. Non-knife flange type ", GB/T 16709.2-2010/ISO 9803-2:2007" Vacuum technology piping Assembly dimensions of parts - Part 2. Flange type "and GB/T 25754-2010/ISO 21358:2007" Vacuum technology Right-angle valve dimensions And pneumatic interface, "the close relationship between them in the standard reference to each other. Vacuum technology to bake the flange Knife flange size
1 Scope
This guidance document specifies the fixed or rotatable type used in vacuum systems with pressures ranging from atmospheric pressure down to 10-13 Pa Baking flange size with bolt-on and blade-type.
2 Terms and definitions
The following terms and definitions apply to this guidance document.
2.1 Knife-edge style flange
Metal sealing flange, used in high vacuum and ultra-high vacuum areas.
Note 1. Insert a metal washer between the two knife-edge flanges, bolting the flanges tight and securing them with the flanged conical cutting edge into the metal washer Of the plane, forming a seal.
Note 2. Initially developed as a CF (Conflat) 1) flange. The wide and consistent use of blade flanges has made it a de facto international standard and is now From this section will be put together into a book.
2.2 Nominal bore
Nominal diameter nominalbore Flanges are used to specify the maximum actual size of pipe that the flange can accommodate.
Note: See Table 1 for the continuation of the convention of marking the original flange with flange OD (in the past in inches).
2.3 Leak check groove
Leak detection leakcheckgroove Grooves machined on the sealing side of the flange allow quick and unobstructed access of the leak gas to the metal washer from the perimeter of the flange Sealing area.
3 Symbol
Symbol name unit l1 flange nominal diameter mm (in) l2 maximum connection diameter mm (in) l3 Bolt hole diameter mm (in) l4 bolt hole center circle diameter mm (in) phi bolt hole center position tolerance mm l5 seal groove diameter mm (in) l6 Knife diameter mm (in) l7 Inner ring thickness mm (in) l8 rotation connection depth mm (in) l9 flange thickness mm (in) l11 metal washer outer diameter mm (in)
1) conflat(R) is a trademark of
Varian. This information is given for the convenience of users of this standard understanding and application, does not constitute ISO some of the product name approval. It can also be used if the same product form produces the same result.
......
This preview omits tables, figures, formulas and parts of the technical clauses. The complete document — 15 pages — is available in the English PDF.
Similar standards
How to Download GB/Z 25756-2010
- 1
Add to cart
Click "Download PDF" on this page and choose "Buy this standard". You can add more standards before checkout.
- 2
Checkout
Enter your email and billing details. Payment is processed securely by Stripe (cards or bank transfer). Prefer bank details? Request a quotation (min. order $300).
- 3
Fast delivery
After payment you'll receive an email confirmation. The English PDF is sent to the same address, usually within minutes and at the latest within 1 business day.
- 4
Invoice included
A tax invoice is attached to the confirmation email. Need a custom invoice? Contact us.
Related Standards
GB/Z 102.17-2026 — Semiconductor devices - Discrete devices - Part 17: Magnetic and capacitive coupler for basic and reinforced insulation
GB/Z 103-2026 — Health informatics - The architecture of internet healthcare service network
GB/Z 108-2026 — Health informatics - Internet healthcare service pattern
GB/Z 25756-2010
$145.00