GB/T 9317-2012General specification for pulse signal generator (English PDF)
脉冲信号发生器通用规范
This is a limited preview
Buy now to download the full PDF (29 pages)
Need quotation for your management?
Get a formal quotation for GB/T 9317-2012 in 30 minutes.
Issued by
SAMR; SAC
Level / Type
National · Recommended
Issue date
December 31, 2012
Implementation date
June 1, 2013
Scope
GB/T 9317-2012 is the English-translated version of 脉冲信号发生器通用规范.
GB/T 9317-2012 is the general specification for pulse signal generators.
It fixes the terminology, the product classification, the requirements, the test methods, the inspection rules and the marking, packaging, transport and storage provisions, and defines the pulse, the double pulse, the pulse train, the burst pulse and pulse polarity; its test methods now also cover output channel delay, pulse level settling time and trigger delay.
The standard is meant as the technical basis for design, type approval, production, use and testing, and for writing product standards for these instruments. It does not apply to continuous or pulsed sine-wave signal generators, to television signal generators, function generators, arbitrary waveform generators or data generators.
It replaces GB/T 9317-1988 and GB/T 9318-1988, was issued on 31 December 2012 and has applied since 1 June 2013.
Found what you need?
Document preview — GB/T 9317-2012
National Standard of the People's Republic of China
- ICS
- 17.220
- Classification
- L 85
- Replacing
- GB/T 9318-1988
Issued by: State Administration for Market Regulation; Standardization Administration of the PRC
Contents
- Preface
- 1 Scope
- 2 Normative references
- 3 Terms and definitions
- 4 8 Categories
- 5 Requirements
- 6 Test methods
- 7 Inspection rules
- 8 signs, packaging, transportation and storage
Foreword
This standard rule according to GB/T 1.1-2009 given draft.
This standard replaces GB/T 9317-1988 "pulse generator technical conditions", GB/T 9318-1988 "pulse generator test Test Methods. " This standard and GB/T 9317-1988 "pulse generator technical conditions", GB/T 9318-1988 "pulse generator test Method "compared to the main changes are as follows.
--- An increase of some terms and definitions;
--- Test method increases the output channel delay, pulse level stabilization time, trigger delay and other parameters.
The standard proposed by the Ministry of Industry and Information Technology of the People's Republic of China.
1 Scope
This standard specifies the pulse signal generator terminology, product classifications, requirements, test methods, inspection rules, marking, packaging, transportation and storage Memory and so on.
This standard applies to the pulse generator, as a product design, the technical basis for the identification, production, use, testing, and also the development of the pulse signal Generator product standard basis.
This standard does not apply to a continuous or pulsed sinusoidal output signal generator television signal generator, function generator, arbitrary waveform Form generator, data generator.
2 Normative references
The following documents for the application of this document is essential. For dated references, only the dated edition applies to this document. For undated references, the latest edition (including any amendments) applies to this document.
GB/T 191 Packing Pictorial marking
GB/T 3047.6 desktop chassis electronics Series of basic dimensions
GB/T 6587-2012 General specification for electronic measuring instruments
GB/T 11463-1989 electronic measuring instrument reliability test Part 1 Electrical equipment compatibility requirements GB/T 18268.1 measurement, control and laboratory use. General requirements
3 Terms and Definitions
The following terms and definitions apply to this document.
3.1 Pulse signal
3.1.1 Pulse
A departure from the first state to reach the second rated rated state and eventually return to a first electrical signal nominal state.
3.1.2 Double pulse
Two pulses of the same polarity occurs within a waveform cycle, commonly referred to as "double pulse" with two pulse width can vary.
3.1.3 Pulse sequence streampulses
Continuously repeated series of pulse waveform.
3.1.4 Group Pulse burstpulse
The number of pulses occur within a period greater than 2 and limited pulse signal.
3.1.5 Pulse polarity
Described pulse waveform corresponding to two nominal state level the relationship between the waveform parameters, the first state rated higher than the second pulse is rated condition
......
This preview omits tables, figures, formulas and parts of the technical clauses. The complete document — 29 pages — is available in the English PDF.
Referenced standards
Normative references
Similar standards
Editions of GB/T 9317
| Edition | Title | Revision | Status |
|---|---|---|---|
| GB/T 9317-2012 | General specification for pulse signal generator | current edition | Current |
| GB/T 9318-1988 | General specification for pulse signal generator | previous edition | Superseded |
This page sells the current edition, GB/T 9317-2012. Earlier editions are listed for reference only.
How to Download GB/T 9317-2012
- 1
Add to cart
Click "Download PDF" on this page and choose "Buy this standard". You can add more standards before checkout.
- 2
Checkout
Enter your email and billing details. Payment is processed securely by Stripe (cards or bank transfer). Prefer bank details? Request a quotation (min. order $300).
- 3
Instant delivery (0–9 sec)
Delivery is automatic: within seconds of payment you'll receive an email with a secure download link. The link stays valid for 72 hours.
- 4
Invoice included
A tax invoice is attached to the confirmation email. Need a custom invoice? Contact us.
Related Standards
GB/T 11463-1989 — Reliability test for electronic measuring instruments
GB/T 191-2025 — Graphical symbols marking for handling and storage of packages
GB/T 1910-2015 — Newsprint
Secure payment via Stripe
Payments accepted
GB/T 9317-2012
$465.00