GB/T 6792-2009Measure method of stress and deformation for bus skeleton (English PDF)
客车骨架应力和形变测量方法
This is a limited preview
Buy now to download the full PDF (16 pages)
Need quotation for your management?
Get a formal quotation for GB/T 6792-2009 in 30 minutes.
Issued by
SAMR; SAC
Level / Type
National · Recommended
Issue date
March 23, 2009
Implementation date
January 1, 2010
Scope
GB/T 6792-2009 is the English-translated version of 客车骨架应力和形变测量方法.
GB/T 6792-2009 is the Chinese standard "Measure method of stress and deformation for bus skeleton". Its scope clause reads: This standard specifies the bus skeleton stress and strain measuring instruments, auxiliary equipment, measurement conditions, measurement methods, measurement results and measurement processing Report the amount of content.
This standard applies to passenger cars backbone non ramjet body, you can refer to other passenger use. Its clauses include terms and definitions; measuring instruments and auxiliary equipment; measurement conditions.
Found what you need?
Document preview — GB/T 6792-2009
National Standard of the People's Republic of China
- ICS
- 43.080.20
- Classification
- T 42
- Replacing
- GB/T 6792-1996
Issued by: State Administration for Market Regulation; Standardization Administration of the PRC
Contents
- 1 Scope
- 2 Normative references
- 3 Terms and Definitions
- 4 measuring instruments and auxiliary equipment
- 5 measurement conditions
1 Scope
This standard specifies the bus skeleton stress and strain measuring instruments, auxiliary equipment, measurement conditions, measurement methods, measurement results and measurement processing
Report the amount of content.
This standard applies to passenger cars backbone non ramjet body, you can refer to other passenger use.
2 Normative references
The following documents contain provisions which, through reference in this standard and become the standard terms. For dated references, subsequent
Amendments (not including errata content) or revisions do not apply to this standard, however, encourage the parties to the agreement are based on research
Whether the latest versions of these documents. For undated reference documents, the latest versions apply to this standard.
GB/T 4780-2000 term auto body
GB/T 12428 quality passenger load calculation method
GB/T 12674 Automotive Quality (by weight) parameter measurement method
GB 12676 automotive braking systems structure, performance and test methods
3 Terms and Definitions
GB/T 4780-2000 and established in the following terms and definitions apply to this standard.
3.1
Passenger load carrying body and the chassis frame.
4 measuring instruments and auxiliary equipment
4.1 Measuring Instruments
Static strain gauges, dynamic strain gauge, data acquisition systems, signal processing systems, roll meter, multimeter, megger, vehicle road simulation vibration
Dynamic test stand and so on.
4.2 aids
Support vehicle stool, bar, plate, gauge length, triangular wood and other (straight length and regulations may make reference to Appendix A).
5 measurement conditions
5.1 Environment
5.1.1 Static measurements indoors
Temperature of -10 °C ~ 40 °C, the rate of change does not exceed ± 2 °C/h; relative humidity less than
85%; no direct sunlight, heat radiation, wind and corrosive gases; non-frequency magnetic field interference.
5.1.2 Dynamic measurements on roads
A temperature of 0 ~ 40 °C, the rate of change does not exceed ± 2 °C/h; relative humidity less than 85%; test
No amount of link power frequency magnetic field interference.
Testing, environmental conditions 5.1.3 in the vehicle road simulation vibration test rig reference 5.1.1.
5.2 Site
5.2.1
static measurement site should be flat, the angle of inclination of not more than 1%, otherwise the plate pad level.
5.2.2
dynamic measurement sections should be similar to bus line runs required in Table 1.
......
This preview omits tables, figures, formulas and parts of the technical clauses. The complete document — 16 pages — is available in the English PDF.
Referenced standards
Similar standards
Editions of GB/T 6792
| Edition | Title | Revision | Status |
|---|---|---|---|
| GB/T 6792-2009 | Measure method of stress and deformation for bus skeleton | current edition | Current |
| GB/T 6792-1996 | Measure method of stress and deformation for bus skeleton | previous edition | Superseded |
This page sells the current edition, GB/T 6792-2009. Earlier editions are listed for reference only.
How to Download GB/T 6792-2009
- 1
Add to cart
Click "Download PDF" on this page and choose "Buy this standard". You can add more standards before checkout.
- 2
Checkout
Enter your email and billing details. Payment is processed securely by Stripe (cards or bank transfer). Prefer bank details? Request a quotation (min. order $300).
- 3
Instant delivery (0–9 sec)
Delivery is automatic: within seconds of payment you'll receive an email with a secure download link. The link stays valid for 72 hours.
- 4
Invoice included
A tax invoice is attached to the confirmation email. Need a custom invoice? Contact us.
Related Standards
GB/T 10003-2026 — Biaxially oriented polypropylene (BOPP) film
GB/T 10004-2026 — Plastic/Plastic laminated films and pouches for packaging
GB/T 10007-2026 — Rigid cellular plastics - Determination of shear properties
Secure payment via Stripe
Payments accepted
GB/T 6792-2009
$285.00