GB/T 5660-2013End-suction centrifugal pumps—Baseplate and installation dimensions (English PDF)
轴向吸入离心泵 底座尺寸和安装尺寸
This is a limited preview
Buy now to download the full PDF (15 pages)
Need quotation for your management?
Get a formal quotation for GB/T 5660-2013 in 30 minutes.
Issued by
SAMR; SAC
Level / Type
National · Recommended
Issue date
December 17, 2013
Implementation date
October 1, 2014
Scope
GB/T 5660-2013 is the English-translated version of 轴向吸入离心泵 底座尺寸和安装尺寸.
GB/T 5660-2013 is the Chinese standard "End-suction centrifugal pumps—Baseplate and installation dimensions". Its scope clause reads: This standard specifies the axial suction centrifugal pump (hereinafter referred to as the pump) base and installation dimensions.
This standard applies to pumps and Y2, Y3 series three-phase asynchronous motors. Its clauses include base and installation dimensions.
Found what you need?
Document preview — GB/T 5660-2013
National Standard of the People's Republic of China
- ICS
- 23.080
- Classification
- J 71
- Replacing
- GB/T 5660-1985
Issued by: State Administration for Market Regulation; Standardization Administration of the PRC
Contents
- Foreword
- 1 Scope
- 2 Normative references
- 3 Terms and definitions
1 Scope
This standard specifies the axial suction centrifugal pump (hereinafter referred to as the pump) base and installation dimensions.
This standard applies to pumps and Y2, Y3 series three-phase asynchronous motors.
2 Normative references
The following documents for the application of this document is essential. For dated references, only the dated version suitable for use herein
Member. For undated references, the latest edition (including any amendments) applies to this document.
GB/T 5662 suction centrifugal pumps (16bar) mark, performance and size
JB/T 8680 Y2 series (IP54) three-phase induction motor (frame size 63 to 355)
JB/T 10447 Y3 series (IP55) three-phase induction motor (frame size 63 to 355)
3 base and installation dimensions
3.1
pump size should be consistent with the provisions of GB/T 5662's. Motor mounting dimensions should be consistent with JB T 8680 JB/T provision/10447 of.
3.2
base number and size are shown in Table 1 and Figure 1. The basic dimensions are shown in Table 2.
Table 1 chassis number and size in millimeters size
Base number
2,345,678,910,111,213
L1 800 900 1000 1120 1250 1400 1600 1800 1920 2110 2200 2370
L2 130 150 170 190 205 230 270 300 250 250 250 250
L3 540 600 660 740 840 940 1060 1200 1400 1600 1700 1800
L4 ± 25 35 35 40 40 45 50 55 55 70 70 70 70
L5 0 0 0 0 0 0 0 0 700 800 850 900
B1 270 300 340 380 430 480 530 600 660 770 770 860
B2 320 350 400 440 490 550 600 670 710 820 820 920
B3 360 390 450 490 540 610 660 730 780 890 890 990 hmax 125 125 125 140 160 180 200 200 110 110 110 150 da hole with bolt M16 M16 M20 M20 M20 M24 M24 M24 M24 M24 M24 M24
Note. The table dimensions L1 and B1, respectively, for the length and width of the working area, excluding casting error.
a hole size according to GB/T 5277 in dh provisions.
......
This preview omits tables, figures, formulas and parts of the technical clauses. The complete document — 15 pages — is available in the English PDF.
Referenced standards
Similar standards
Editions of GB/T 5660
| Edition | Title | Revision | Status |
|---|---|---|---|
| GB/T 5660-2013 | End-suction centrifugal pumps—Baseplate and installation dimensions | current edition | Current |
| GB/T 5660-1985 | End-suction centrifugal pumps—Baseplate and installation dimensions | previous edition | Superseded |
This page sells the current edition, GB/T 5660-2013. Earlier editions are listed for reference only.
How to Download GB/T 5660-2013
- 1
Add to cart
Click "Download PDF" on this page and choose "Buy this standard". You can add more standards before checkout.
- 2
Checkout
Enter your email and billing details. Payment is processed securely by Stripe (cards or bank transfer). Prefer bank details? Request a quotation (min. order $300).
- 3
Instant delivery (0–9 sec)
Delivery is automatic: within seconds of payment you'll receive an email with a secure download link. The link stays valid for 72 hours.
- 4
Invoice included
A tax invoice is attached to the confirmation email. Need a custom invoice? Contact us.
Related Standards
GB/T 10003-2026 — Biaxially oriented polypropylene (BOPP) film
GB/T 10004-2026 — Plastic/Plastic laminated films and pouches for packaging
GB/T 10007-2026 — Rigid cellular plastics - Determination of shear properties
Secure payment via Stripe
Payments accepted
GB/T 5660-2013
$125.00