GB/T 38588-2020In-situ measurements of heat loss of insulating pipes for urban heat-supplying (English PDF)
城镇供热保温管网系统散热损失现场检测方法
This is a limited preview
Buy now to download the full PDF (20 pages)
Need quotation for your management?
Get a formal quotation for GB/T 38588-2020 in 30 minutes.
Issued by
SAMR; SAC
Level / Type
National · Recommended
Issue date
March 31, 2020
Implementation date
February 1, 2021
Scope
GB/T 38588-2020 is the English-translated version of 城镇供热保温管网系统散热损失现场检测方法.
GB/T 38588-2020 is the Chinese standard "In-situ measurements of heat loss of insulating pipes for urban heat-supplying".
Its scope clause reads: This standard specifies the terms, definitions and symbols, test methods, test grading and use conditions, test requirements, data processing, test errors and test reports of in-situ measurements of heat loss of insulating pipes for urban heat-supplying.
This standard is applicable to the in-situ measurement of heat loss of insulating pipes, pipe interfaces and their fittings (hereinafter referred to as pipelines) for urban heat-supplying with the hot water medium temperature less than or equal to 150 °C and the steam medium temperature less than or equal to 350 °C. Its clauses include terms, definitions and symbols.
Found what you need?
Document preview — GB/T 38588-2020
National Standard of the People's Republic of China
- ICS
- 91.140.10
- Classification
- P 46
Issued by: State Administration for Market Regulation; Standardization Administration of the PRC
Contents
- Foreword i
- 1 Scope
- 2 Normative references
- 3 Terms, definitions and symbols
- 3.1 Terms and definitions
- 3.2 Symbols
- 4 Test methods
- 4.1 Heat flow meter apparatus method
- 4.2 Surface temperature method
- 4.3 Temperature difference method
- 4.4 Heat balance method
- 5 Test grading and service conditions
- 5.1 Test grading and selection
- 5.2 Test apparatus
- 6 Test requirements
- 6.1 Test preparation
- 6.2 Layout of test sections and measuring points
- 6.3 Environmental conditions for test
- 6.4 Test procedures
- 7 Data processing
- 7.1 Data collation
- 7.2 Calculation of heat loss
- 8 Test error
- 8.1 Error analysis
- 8.2 Error range
- 9 Test report
- Annex A (Normative) Heat flux correction
- Annex B (Normative) Calculation of the overall heat transfer coefficient by surface temperature method
- Annex C (Normative) Investigation form of condition along the thermal insulation pipeline
- Annex D (Normative) Test data record form for heat loss of insulation construction of thermal insulation pipeline
1 Scope
This standard specifies the terms, definitions and symbols, test methods, test grading and use conditions, test requirements, data processing, test errors and test reports of in-situ measurements of heat loss of insulating pipes for urban heat-supplying.
This standard is applicable to the in-situ measurement of heat loss of insulating pipes, pipe interfaces and their fittings (hereinafter referred to as pipelines) for urban heat-supplying with the hot water medium temperature less than or equal to 150 °C and the steam medium temperature less than or equal to 350 °C.
2 Normative references
The following referenced documents are indispensable for the application of this document. For dated references, only the edition cited applies. For undated references, the latest edition of the referenced document (including any amendments) applies.
GB/T 10295 Thermal insulation - Determination of steady-state thermal resistance and related properties - Heat flow meter apparatus
GB/T 17357 In-situ measurements of heat loss through thermal insulation of equipments and pipes - Heat flow meter apparatus and surface temperature method
JJF 1059.1-2012 Evaluation and expression of uncertainty in measurement
3 Terms, definitions and symbols
3.1 Terms and definitions
For the purposes of this document, the following terms and definitions apply.
3.1.1 steady heat transfer
heat transfer process in which the radial temperature at each point does not change with time in the thermal insulation structure layer of thermal insulation pipeline
3.1.2 heat flow meter apparatus method
heat flux test method for directly measuring radial heat transfer of insulation construction of thermal insulation pipeline with thermal resistance type heat flux sensor (heat flux probe) and measurement indicator
3.1.3 surface temperature method
heat flux test method for calculating radial heat transfer by measuring the outer surface temperature, ambient temperature, wind direction and speed, surface thermal emissivity and external dimensions of insulation construction
3.1.4 temperature difference method
heat flux test method for calculating radial heat transfer of insulation construction by measuring the material thickness of each layer of insulation construction, the temperature on the interface of each layer and the thermal conductivity of each layer of materials at the service temperature
3.1.5 heat balance method
method for calculating the whole heat loss value of the pipeline according to the enthalpy difference method or the principle of energy balance by in-situ measurement of the medium flow of the pipeline under test, the medium temperature and (or) pressure at the starting point and the end point of the pipeline under the stable operation state of pipe network system
3.1.6 pseudo steady state of transducer
heat transfer state when the difference of average reading of the heat flux sensor is not greater than 2% and the difference of average reading of the temperature sensor at the same measuring point is not greater than 0.2 °C in two consecutive 5-minute cycles
3.1.7 heat flux
heat passing through a unit cross-sectional area of an object per unit time
3.1.8 insulation construction
generic term of insulating layer and protective cover
3.1.9 ground temperature
natural temperature of soil at the same depth as the tested insulation construction, which is greater than or equal to 10 m away from the laying site of the tested insulation construction
3.2 Symbols
For the purposes of this document, the following symbols apply.
a1—the temperature factor, K3;
CA—the calculation coefficient of approximate value of overall heat transfer coefficient for the outer surface of horizontal pipeline;
CB—the calculation coefficient of approximate value of overall heat transfer coefficient for the outer surface of vertical pipeline;
Cr—the radiation coefficient of material surface, W/(m2·K4);
......
This preview omits tables, figures, formulas and parts of the technical clauses. The complete document — 20 pages — is available in the English PDF.
Similar standards
How to Download GB/T 38588-2020
- 1
Add to cart
Click "Download PDF" on this page and choose "Buy this standard". You can add more standards before checkout.
- 2
Checkout
Enter your email and billing details. Payment is processed securely by Stripe (cards or bank transfer). Prefer bank details? Request a quotation (min. order $300).
- 3
Fast delivery
After payment you'll receive an email confirmation. The English PDF is sent to the same address, usually within minutes and at the latest within 1 business day.
- 4
Invoice included
A tax invoice is attached to the confirmation email. Need a custom invoice? Contact us.
Related Standards
GB/T 10003-2026 — Biaxially oriented polypropylene (BOPP) film
GB/T 10004-2026 — Plastic/Plastic laminated films and pouches for packaging
GB/T 10007-2026 — Rigid cellular plastics - Determination of shear properties
GB/T 38588-2020
$355.00