GB/T 38429.1-2019Explosion protected safety technique of automotive LPG filling stations—Part 1: Explosion protected safety technique requirements for LPG dispensers (English PDF)
燃气加气站防爆安全技术 第1部分：液化石油气(LPG)加气机防爆要求
This is a limited preview
Buy now to download the full PDF (19 pages)
Need quotation for your management?
Get a formal quotation for GB/T 38429.1-2019 in 30 minutes.
Issued by
SAMR; SAC
Level / Type
National · Recommended
Issue date
December 31, 2019
Implementation date
July 1, 2020
Scope
GB/T 38429.1-2019 is the English-translated version of 燃气加气站防爆安全技术 第1部分：液化石油气(LPG)加气机防爆要求.
GB/T 38429.1-2019 is the Chinese standard "Explosion protected safety technique of automotive LPG filling stations—Part 1: Explosion protected safety technique requirements for LPG dispensers".
Its scope clause reads: This part of GB/T 38429 specifies the requirements, type tests, and routine tests for liquefied petroleum gas (LPG) dispensers for gas filling stations.
Inspections, documents and signs. This section applies to LPG gas filling stations for vehicles with a design pressure of 2500kPa, a maximum pipeline of DN40 and a container volume of less than 2L Gas engine.
This section also applies to multi-fuel dispenser LPG components. This section does not apply to dispensers with integrated pumps. Note. For the filling of civil gas cylinders, please refer to this section. Its clauses include terms and definitions.
Found what you need?
Document preview — GB/T 38429.1-2019
National Standard of the People's Republic of China
- ICS
- 29.260.20
- Classification
- K 35
Issued by: State Administration for Market Regulation; Standardization Administration of the PRC
Contents
- Foreword III
- 1 Scope
- 2 Normative references
- 3 Terms and definitions
- 4 Requirement
- 5 Type test
- 6 Routine test
- 7 File
- 8 Signs and identifications
- Appendix A (informative) Related information on explosion-proof equipment
- Appendix B (Normative Appendix) Classification of Hazardous Locations in Dispensers and Adjacent Areas
- Appendix C (Normative) Classification of Oil and Gas Barriers
- References
1 Scope
This part of GB/T 38429 specifies the requirements, type tests, and routine tests for liquefied petroleum gas (LPG) dispensers for gas filling stations.
Inspections, documents and signs.
This section applies to LPG gas filling stations for vehicles with a design pressure of 2500kPa, a maximum pipeline of DN40 and a container volume of less than 2L
Gas engine. This section also applies to multi-fuel dispenser LPG components.
This section does not apply to dispensers with integrated pumps.
Note. For the filling of civil gas cylinders, please refer to this section.
2 Normative references
The following documents are essential for the application of this document. For dated references, only the dated version applies to this article
Pieces. For undated references, the latest version (including all amendments) applies to this document.
GB/T 1226 general pressure gauge
GB 3836.1 Explosive atmospheres Part 1. General requirements for equipment
GB 3836.3 Explosive atmospheres-Part 3. Equipment protected by increased safety "e"
GB 3836.14 Explosive atmospheres Part 14. Classification of places for explosive atmospheres
GB/T 3836.15 Explosive atmospheres Part 15. Design, selection and installation of electrical installations
GB/T 4208 enclosure protection grade (IP code)
GB 4943.1 Information technology equipment security-Part 1. General requirements
GB/T 5013.4 Rubber insulated cables with a rated voltage of 450/750V and below. Part 4. Flexible wires and flexible cables
GB/T 5023.7 Polyvinyl chloride insulated cables with a rated voltage of 450/750V and below. Part 7. Two or more cores shielded and non-
Shielded flexible cable
GB/T 5226.1-2019 Machinery Electrical Safety Machinery Electrical Equipment Part 1. General Technical Conditions
GB/T 10546 Rubber hoses for conveying liquid or gaseous liquefied petroleum gas (LPG) and natural gas at a pressure of 2.5 MPa and below
And hose assembly specifications
GB/T 14048.3 Low-voltage switchgear and control equipment. Part 3. Switch, isolator, disconnector and fuse combination appliance
GB/T 14536.1 Electric automatic controllers for household and similar use Part 1. General requirements
GB/T 19235 LPG Filler Refill Gun
GB/T 22380.1 Explosion-proof safety technology for fuel filling stations Part 1. Technical requirements for explosion-proof safety of fuel dispensers
GB 25285.1 Explosion prevention and protection in explosive environment Part 1. Basic principles and methods
GB 25286.1 Non-electrical equipment for explosive atmospheres-Part 1. Basic methods and requirements
GB 50058 Design code for electrical installations in explosive atmospheres
3 terms and definitions
The following terms and definitions apply to this document.
......
This preview omits tables, figures, formulas and parts of the technical clauses. The complete document — 19 pages — is available in the English PDF.
Similar standards
How to Download GB/T 38429.1-2019
- 1
Add to cart
Click "Download PDF" on this page and choose "Buy this standard". You can add more standards before checkout.
- 2
Checkout
Enter your email and billing details. Payment is processed securely by Stripe (cards or bank transfer). Prefer bank details? Request a quotation (min. order $300).
- 3
Instant delivery (0–9 sec)
Delivery is automatic: within seconds of payment you'll receive an email with a secure download link. The link stays valid for 72 hours.
- 4
Invoice included
A tax invoice is attached to the confirmation email. Need a custom invoice? Contact us.
Related Standards
GB/T 38429.2-2019 — Explosion protected safety technique of automotive LPG filling stations—Part 2: Explosion protected components related to LPG dispensers and installation requirements
GB/T 10003-2026 — Biaxially oriented polypropylene (BOPP) film
GB/T 10004-2026 — Plastic/Plastic laminated films and pouches for packaging
Secure payment via Stripe
Payments accepted
GB/T 38429.1-2019
$325.00