GB/T 38312-2019Code for mooring and sea trials of large yachts (English PDF)
大型游艇系泊、航行试验规程
This is a limited preview
Buy now to download the full PDF (41 pages)
Need quotation for your management?
Get a formal quotation for GB/T 38312-2019 in 30 minutes.
Issued by
SAMR; SAC
Level / Type
National · Recommended
Issue date
December 10, 2019
Implementation date
July 1, 2020
Scope
GB/T 38312-2019 is the English-translated version of 大型游艇系泊、航行试验规程.
GB/T 38312-2019 is the Chinese standard "Code for mooring and sea trials of large yachts". Its scope clause reads: This standard specifies the general requirements for mooring and sailing tests of large yachts, the test items for mooring and sailing tests, and their test strips.
Documents, test content and procedures, test records and reports. This standard applies to the relevant tests of large yachts. Its clauses include general requirements.
Found what you need?
Document preview — GB/T 38312-2019
National Standard of the People's Republic of China
- ICS
- 47.020
- Classification
- U 18
Issued by: State Administration for Market Regulation; Standardization Administration of the PRC
Contents
- Foreword III
- 1 Scope
- 2 Normative references
- 3 General requirements
- 4 Mooring test
- 4.1 Anchor equipment and windlass
- 4.2 Rudder gear and steering gear
- 4.3 Life-saving equipment
- 4.4 Tethering device
- 4.5 Doors, windows, hatch covers and other opening closing devices
- 4.6 Signal equipment
- 4.7 Fire suppression system
- 4.8 Fire detection and fire alarm system
- 4.9 Bilge water system and oil sewage oil filtering equipment 5
- 4.10 Living and drainage systems
- 4.11 Ventilation system
- 4.12 Air-conditioning system
- 4.13 Air quality in the cabin
- 4.14 Fin stabilizers, wave pressure plates, boarding stairs
- 4.15 Main propulsion system
- 4.16 Diesel generator sets and distribution boards
- 4.17 Electric propulsion system, side thruster, stabilizer gyro
- 4.18 Charge and discharge board and battery pack
- 4.19 Main and emergency lighting
- 4.20 Radio communication equipment
- 4.21 Navigational equipment
- 4.22 Test Contents and Procedures of Alarm System
- 4.23 Ship-wide information system
- 5 Sailing test
- 5.1 Ship performance test
- 5.2 Anchor Test
- 5.3 Main propulsion system test
- 5.4 Operation test of diesel generator set
- 5.5 Alarm System
- 5.6 Radio communication equipment
- 5.7 Navigational equipment
- 5.8 Hull vibration test
- 5.9 Ship noise test
- 5.10 Fin stabilizers, pressure wave stabilizers, gyroscopic stabilizers
- Appendix A (Informative) Test Record Form
1 Scope
This standard specifies the general requirements for mooring and sailing tests of large yachts, the test items for mooring and sailing tests, and their test strips.
Documents, test content and procedures, test records and reports.
This standard applies to the relevant tests of large yachts.
2 Normative references
The following documents are essential for the application of this document. For dated references, only the dated version applies to this article
Pieces. For undated references, the latest version (including all amendments) applies to this document.
GB/T 3221 Mooring and Navigation Test Outline for Diesel-Powered Inland Waterway Ships
GB/T 3471 General rules for sea-boat mooring and navigational tests
3 General requirements
3.1
Before the mooring test of each newly built yacht, the design unit or shipyard shall compile the ship in consultation with relevant units according to the provisions of this standard
The test items and specific test outlines to be carried out shall be submitted to the shipowner for confirmation and the ship survey agency for approval.
3.2
Prior to the mooring test, the hull construction, equipment, devices and systems shall be constructed, installed and commissioned in accordance with the requirements of the drawings and technical documents.
carry out.
3.3
The test results of each project shall meet the requirements of applicable regulations, rules, conventions, codes or standards.
3.4
The test equipment and instruments used for mooring test and navigation test should be signed by the relevant national authority or an approved testing agency.
Issued a valid certificate of conformity or test report. For testing equipment and instruments related to statutory and classification inspections, the units that perform the inspections are
The right to check its accuracy level, periodic documents or records.
3.5
If the marine products installed on board are in the list of certificates and regulations, they should hold the marine product certificate issued by the ship inspection agency.
Book, certificate of approval. Lifting equipment (such as stern doors, booms, etc.) and dinghy rigs have clear test requirements in relevant regulations.This standard
No longer explained.
3.6
Prior to the sailing test, the tilt test shall be completed in accordance with the technical documents approved by the ship inspection agency, and the test report shall be approved by the ship inspection agency.
Quasi-recognition. For sister ships, the calculation of the center of gravity for empty ships should be approved by the ship survey agency. Completion stability meter to enter the results of the tilt test
The calculation should be approved by the ship survey agency.
3.7
Prior to the sailing test, the mooring test of the whole boat shall be completed and the test results shall be satisfactory. The faults and defects found in the mooring test shall be eliminated, and
Obtain a sea trial certificate issued by a ship inspection agency.
3.8
Shipyards shall make various test records during mooring and navigation tests. After the test, the shipyard shall sort out the relevant technical documents
And test report, and submitted as necessary technical documents for survey and delivery to the ship inspection agency and ship-using unit.
3.9
The mooring test is to check the construction and installation quality of the hull, device, electromechanical equipment and related systems of the yacht and its static conditions.
Work conditions, determine initially whether the expected performance can be achieved, and then determine whether the conditions for sailing tests are met.
3.10
The sailing test is a test of the marine performance, mechanical equipment and electrical equipment of the yacht to verify the overall performance and equipment of the yacht.
In accordance with legal and regulatory requirements, determine that all projects meet the design goals. Before the sailing test, the main and auxiliary aircraft and auxiliary equipment, and the bilge
Water system, anchor equipment, rudder equipment, life-saving equipment, fire-fighting equipment, navigation equipment, signal equipment, communication equipment, watertight devices, tilt test […]
......
This preview omits tables, figures, formulas and parts of the technical clauses. The complete document — 41 pages — is available in the English PDF.
Similar standards
How to Download GB/T 38312-2019
- 1
Add to cart
Click "Download PDF" on this page and choose "Buy this standard". You can add more standards before checkout.
- 2
Checkout
Enter your email and billing details. Payment is processed securely by Stripe (cards or bank transfer). Prefer bank details? Request a quotation (min. order $300).
- 3
Fast delivery
After payment you'll receive an email confirmation. The English PDF is sent to the same address, usually within minutes and at the latest within 1 business day.
- 4
Invoice included
A tax invoice is attached to the confirmation email. Need a custom invoice? Contact us.
Related Standards
GB/T 10003-2026 — Biaxially oriented polypropylene (BOPP) film
GB/T 10004-2026 — Plastic/Plastic laminated films and pouches for packaging
GB/T 10007-2026 — Rigid cellular plastics - Determination of shear properties
GB/T 38312-2019
$840.00