GB/T 38298-2019Test method of auto-ignition temperature for solid chemicals (English PDF)
固体化学品自动点火温度的试验方法
This is a limited preview
Buy now to download the full PDF (15 pages)
Need quotation for your management?
Get a formal quotation for GB/T 38298-2019 in 30 minutes.
Issued by
SAMR; SAC
Level / Type
National · Recommended
Issue date
December 10, 2019
Implementation date
April 1, 2020
Scope
GB/T 38298-2019 is the English-translated version of 固体化学品自动点火温度的试验方法.
GB/T 38298-2019 is the Chinese standard "Test method of auto-ignition temperature for solid chemicals".
Its scope clause reads: This standard specifies the test method for the automatic ignition temperature of solid chemicals, that is, the automatic point of extrapolation of solid chemicals under a large amount of accumulation Fire temperature prediction method.
This standard is applicable to the test of automatic ignition temperature of powdery or granular chemicals. Its clauses include method principle; reagents or materials; equipment.
Found what you need?
Document preview — GB/T 38298-2019
National Standard of the People's Republic of China
- ICS
- 13.300
- Classification
- A 80
Issued by: State Administration for Market Regulation; Standardization Administration of the PRC
Contents
- 1 Scope
- 2 Normative references
- 3 Method principle
- 4 Reagents or materials
- 5 Equipment
1 Scope
This standard specifies the test method for the automatic ignition temperature of solid chemicals, that is, the automatic point of extrapolation of solid chemicals under a large amount of accumulation
Fire temperature prediction method.
This standard is applicable to the test of automatic ignition temperature of powdery or granular chemicals.
2 Normative references
The following documents are essential for the application of this document. For dated references, only the dated version applies to this article
Pieces. For undated references, the latest version (including all amendments) applies to this document.
GB/T 5330 Industrial wire woven square mesh screen
GB/T 30429 Industrial Thermocouple
3 Method principle
The solid auto-ignition temperature is the ambient temperature when the temperature of the sample changes suddenly when the solid powder is heated. As the sample test size increases
Add, chemical auto-ignition temperature will decrease accordingly. By measuring the ignition temperature of the sample under different test sizes (small sizes), the
Extrapolated auto-ignition temperature for samples in bulk conditions.
4 Reagents or materials
Caution --- If it is explosive, the automatic ignition temperature test under small size conditions should be carried out first.
The sample to be tested should be powdery or granular.
5 Equipment
5.1 Thermocouple
K type, range 0 °C ~ 1200 °C, accuracy 0.1 °C, should meet the requirements of GB/T 30429.
5.2 Metal mesh container
It shall meet the requirements of GB/T 5330. During the test, the cylindrical metal mesh container is preferred (the volume can be selected)
100cm3, 1000cm3, 1600cm3, etc.), the diameter of the container is equal to the height of the container, and the mesh side length of the metal mesh is 0.05mm; also
Other shapes of metal mesh containers can be selected, but the influence of container shape needs to be considered when processing data.
5.3 Sample holder
used to fix the metal mesh container.
5.4 Environmental test box
The heating rate of the box is adjustable, and the heating medium is air. The temperature control range of the test box is from room temperature to 400 °C.
5.5 Temperature data acquisition instrument
The frequency of data acquisition is not less than 1Hz.
5.6
The schematic diagram of the auto-ignition test is shown in Figure 1.
......
This preview omits tables, figures, formulas and parts of the technical clauses. The complete document — 15 pages — is available in the English PDF.
Similar standards
How to Download GB/T 38298-2019
- 1
Add to cart
Click "Download PDF" on this page and choose "Buy this standard". You can add more standards before checkout.
- 2
Checkout
Enter your email and billing details. Payment is processed securely by Stripe (cards or bank transfer). Prefer bank details? Request a quotation (min. order $300).
- 3
Fast delivery
After payment you'll receive an email confirmation. The English PDF is sent to the same address, usually within minutes and at the latest within 1 business day.
- 4
Invoice included
A tax invoice is attached to the confirmation email. Need a custom invoice? Contact us.
Related Standards
GB/T 10003-2026 — Biaxially oriented polypropylene (BOPP) film
GB/T 10004-2026 — Plastic/Plastic laminated films and pouches for packaging
GB/T 10007-2026 — Rigid cellular plastics - Determination of shear properties
GB/T 38298-2019
$85.00