Valid

GB/T 36805.2-2020Plastics—Determination of tensile properties at high strain rates—Part 2: Direct testing method (English PDF)

塑料 高应变速率下的拉伸性能测定 第2部分:直接测试法

Preview PDF

This is a limited preview

Buy now to download the full PDF (15 pages)

Need quotation for your management?

Get a formal quotation for GB/T 36805.2-2020 in 30 minutes.

Issued by

SAMR; SAC

Level / Type

National · Recommended

Issue date

November 19, 2020

Implementation date

October 1, 2021

Scope

GB/T 36805.2-2020 is the English-translated version of 塑料 高应变速率下的拉伸性能测定 第2部分:直接测试法.

GB/T 36805.2-2020 is the Chinese standard "Plastics - Determination of tensile properties at high strain rates - Part 2: Direct testing method". Its scope clause reads: This Part of GB/T 36805 specifies a method for testing the tensile properties of plastic materials over a wide range of strain rates using a high-speed tensile tester.

This Part applies to tensile tests with a tensile speed above 10mm/s. NOTE: The wide range of strain rates contains rates approximating high strain rates under shock loading.

Its clauses include terms and definitions; principle; apparatus; specimens; status adjustment; test procedures; calculation and presentation of results; test report.

It was issued by the State Administration for Market Regulation on NOVEMBER 19, 2020 and took effect on OCTOBER 01, 2021.

Found what you need?

Document preview — GB/T 36805.2-2020

National Standard of the People's Republic of China

ICS
83.080.01
Classification
G 31

Issued by: State Administration for Market Regulation; Standardization Administration of the PRC

Contents

  • Foreword3
  • Introduction4
  • 1 Scope5
  • 2 Normative References5
  • 3 Terms and Definitions5
  • 4 Principle6
  • 5 Apparatus6
  • 6 Specimens8
  • 7 Status Adjustment8
  • 8 Test Procedures8
  • 9 Calculation and Presentation of Results9
  • 10 Test Report10
  • Appendix A (Informative) Test Equipment12
  • Bibliography14

1 Scope

This Part of GB/T 36805 specifies a method for testing the tensile properties of plastic materials over a wide range of strain rates using a high-speed tensile tester.

This Part applies to tensile tests with a tensile speed above 10mm/s.

NOTE: The wide range of strain rates contains rates approximating high strain rates under shock loading.

2 Normative References

The following documents are essential to the application of this document. For the dated documents, only the versions with the dates indicated are applicable to this document; for the undated documents, only the latest version (including all the amendments) is applicable to this document.

GB/T 1040.1-2018 Plastics - Determination of Tensile Properties - Part 1: General Principles

GB/T 1040.2-2006 Plastics - Determination of Tensile Properties - Part 2: Test Conditions for Molding and Extrusion Plastics

3 Terms and Definitions

For the purposes of this Document, the terms and definitions given in GB/T 1040.1-2018 and the following apply.

3.1 Strain rate; The amount of change in strain per unit time.

NOTE: The unit is per second (s-1).

3.2 Nominal strain rate

The test speed is divided by the length of the narrow parallel portion of the test sample.

NOTE: The unit is per second (s-1).

4 Principle

Using the test system, in the appropriate test mode, set the target strain rate or test speed, data acquisition frequency and other parameters; and stretch along the longitudinal axis of the plastic material specimen at a constant speed until fracture or stress (load) or strain (elongation) reaches a certain predetermined value; and a reliable stress-strain curve is obtained in the process.

5 Apparatus

5.1 Test device

The tester that meets the requirements of this Part shall have the ability to perform tensile tests at speeds above 10mm/s. With the increase of test speed, the measurement error of force value shall increase. These measurement errors are related to the resonant modes of the force sensor, the test sample, and the components in the test device. In order to achieve satisfactory test accuracy and widen the test speed range, the design of the test device is very important. Force sensor (e.g., piezoelectric) with high hardness and components with light weight and high stiffness shall be used. In order to carry out the tensile test at this speed, the equipment usually selects a high-speed tensile tester driven by hydraulic servo and equipped with a buffer. For other testing systems, as long as the tester can provide a constant strain rate that meets the requirements throughout the test process can be used. See Appendix A for test equipment that meets the requirements of this Part.

5.2 Load indicating device

5.2.1 The load indicating device shall be capable of measuring the change in load at any time during the test. The device shall have no inertial lag at the specified test speed.

5.2.2 At high strain rate, the process of spontaneous transfer of load to the specimen shall cause oscillation of the specimen and some parts of the tester; and this oscillation shall be superimposed with the force value signal and recorded in the test curve. The oscillations intensified as the test speed increased. Preventing or reducing the oscillation in the force signal is the key to choosing a dynamic force measurement method. Generally speaking, the farther the force measurement position is from the gauge length, the stronger the oscillation phenomenon.

5.2.3 The use of strain gauges or the use of local dynamic dynamometers as load indicating devices shall be stated in the test report.

5.2.4 The collection frequency fs of the load indicating device shall meet the requirements of the fixture. The specimen shall be clamped in such a way as to prevent the clamped specimen from slipping relative to the jaw of the fixture. The fixture shall not cause premature failure of the specimen at the jaw of the fixture or crush the specimen in the fixture.

6 Specimens

6.1 Specimen shape

For tensile test at high strain rate, the selection of test specimens is related to the specified strain rate, material stiffness, material density, yield strain, piston or beam acceleration, system frequency, and other factors. In order to ensure the comparability of data, the same specimen should be used in the test of a group of samples. The effective area for the test is the narrow parallel section of the sample; and the arc area and the clamping part of the specimen are not used as the effective area for the test. In general, dumbbell-shaped specimens should be selected, see 6.1 in GB/T 1040.2-2006.

6.2 Preparation of specimen

Execute according to 6.2 in GB/T 1040.2-2006.

7 Status Adjustment

Execute according to Clause 8 in GB/T 1040.1-2018.

8 Test Procedures

8.1 Test environment

Execute according to 9.1 in GB/T 1040.1-2018.

8.2 The number of specimens

Execute according to 7.1 in GB/T 1040.1-2018.

8.3 Specimen dimension

Execute according to 9.2 in GB/T 1040.1-2018.

8.4 Clamping

Execute according to 9.3 in GB/T 1040.1-2018.

8.5 Test speed

Determine the strain rate according to the needs of the material application side. After determining the strain rate, calculate the test speed according to Formula (3):

Where: v - test speed, in mm/s;

- nominal strain rate, in s-1;

L1 - length of narrow parallel section of specimen, in mm.

NOTE: The strain rate of 100s-1, 10s-1, and 1s-1 should be used for the test. If other strain rates are required for the test, it can be agreed by the relevant parties.

8.6 Data record

Record the distance increment between load on the specimen and the corresponding marking lines or the fixtures, and an automatic recording system should be used.

9 Calculation and Presentation of Results

9.1 General

The stress, strain, stress-strain curve, etc. are measured by methods similar to those in GB/T 1040.1-2018; but compared with quasi-static tensile, the relative combined factors of specimen size, natural frequency of the test system, and the material itself shall have a significant impact on the test results.

9.2 Stress-strain curve

9.2.1 The stress-strain curve is calculated from the original signal; and obtaining a monotonically increasing signal during the test shall facilitate subsequent analysis. If it cannot be obtained due to measurement technical reasons (such as signal interference), a monotonic signal needs to be obtained through a corresponding algorithm. Such as filtering processing, polynomial fitting, polynomial spline function approximation, etc., and shall be clearly stated in the test report. Usually, the user of the test results is responsible for interpreting the data processing basis for the force value oscillation phenomenon on the stress-strain curve. When measuring the tensile properties under high strain rate, it should not perform algorithm processing first, and then decide whether to perform it as needed after the test, otherwise there is a risk of distorting the test data.

9.2.2 In order to further analyze the test results, such as giving the stress-strain curve to obtain some key indicators or providing the input parameters of the finite element calculation; the […]

......
This preview omits tables, figures, formulas and parts of the technical clauses. The complete document — 15 pages — is available in the English PDF.

Referenced standards

Similar standards

How to Download GB/T 36805.2-2020

  1. 1

    Add to cart

    Click "Download PDF" on this page and choose "Buy this standard". You can add more standards before checkout.

  2. 2

    Checkout

    Enter your email and billing details. Payment is processed securely by Stripe (cards or bank transfer). Prefer bank details? Request a quotation (min. order $300).

  3. 3

    Fast delivery

    After payment you'll receive an email confirmation. The English PDF is sent to the same address, usually within minutes and at the latest within 1 business day.

  4. 4

    Invoice included

    A tax invoice is attached to the confirmation email. Need a custom invoice? Contact us.

Related Standards

English PDF
15 pages
Fast delivery
Invoice included
View Cart

Secure payment via Stripe

Payments accepted

VisaMastercardAmerican ExpressApple PayGoogle PayStripe

GB/T 36805.2-2020

$150.00