Valid

GB/T 36143-2018Durable high modulus asphalt mixture for road engineering (English PDF)

道路用高模量抗疲劳沥青混合料

Preview PDF

This is a limited preview

Buy now to download the full PDF (15 pages)

Need quotation for your management?

Get a formal quotation for GB/T 36143-2018 in 30 minutes.

Issued by

SAMR; SAC

Level / Type

National · Recommended

Issue date

May 14, 2018

Implementation date

April 1, 2019

Scope

GB/T 36143-2018 is the English-translated version of 道路用高模量抗疲劳沥青混合料.

GB/T 36143-2018 sets out the requirements for durable high modulus asphalt mixture, a high modulus anti-fatigue mix for the lower layer of asphalt pavements. It applies to new, rebuilt and widened highways of all grades, urban roads, airport pavements and port roads, outside the cold and winter-cold regions.

It defines asphalt binder, dynamic modulus and fatigue life, and states requirements for the raw materials, including binders with a penetration of 10 to 20 (0.1 mm), aggregate and filler, and for the mixture, from mineral gradation and volume design to its performance.

Test methods refer to the Chinese highway test and construction specifications, and the inspection rules cover type inspection, sampling, batching by tonnage per shift and the decision on each batch. It was issued on 14 May 2018 and has applied since 1 April 2019.

Found what you need?

Document preview — GB/T 36143-2018

National Standard of the People's Republic of China

ICS
93.080.20
Classification
Q 20

Issued by: State Administration for Market Regulation; Standardization Administration of the PRC

Contents

  • Foreword3
  • 1 Scope4
  • 2 Normative references4
  • 3 Terms and definitions4
  • 4 Requirements5
  • 5 Test methods6
  • 6 Inspection rules7
  • 7 Transport9
  • Bibliography10

1 Scope

This Standard specifies terms and definitions, requirements, test methods, inspection rules, transport for high modulus anti-fatigue asphalt mixture for road engineering.

This Standard is applicable to the lower layer of the asphalt pavement in the new or rebuilt and expanded roads of various grades of highways, urban roads, airport pavements and port roads in the cold regions outside the winter and cold winter regions.

2 Normative references

The following referenced documents are indispensable for the application of this document. For dated references, only the edition cited applies. For undated references, the latest edition of the referenced document (including any amendments) applies.

JTG E20-2011, Standard Test Methods of Bitumen and Bituminous Mixtures for Highway Engineering

JTG F40-2004, Technical Specification for Construction of Highway Asphalt Pavements

JTG E60-2008, Field Test Methods of Subgrade and Pavement for Highway Engineering

3 Terms and definitions

For the purposes of this document, the following terms and definitions apply.

3.1 Asphalt binder

a bituminous substance that is capable of binding aggregates into a mass [NB/SH/T 0652-2010, definition 3.1.7]

3.2 Dynamic modulus

the absolute value of the ratio of stress to recovery strain peak for asphalt mixture test piece at specific test temperature and sinusoidal loading mode

3.3 Fatigue life

the corresponding number of loading cycles of asphalt mixture test piece when its bending stiffness modulus is reduced to a certain extent under continuous sine wave loading mode controlled by certain temperature, loading frequency and constant strain control

NOTE: In general, a certain extent means that the bending stiffness modulus of the test piece is reduced to 50% of the initial bending stiffness modulus.

4 Requirements

4.1 Raw material

4.1.1 Asphalt binder

4.1.1.1 Asphalt binder shall meet the requirements for road petroleum asphalt specified in Table 4.2.1-2 of JTG F40-2004 and polymer modified asphalt specified in Table 4.6.2. And add additives as needed.

4.1.1.2 Asphalt binder can also use the asphalt of which the penetration is 10~20 [25°C, 100g, 5s (0.1mm)].

4.1.2 Aggregate, packing

Aggregate and packing shall meet the relevant requirements for aggregate and packing in JTG F40-2004.

4.2 Asphalt mixture

4.2.1 Volume design

4.2.1.1 Mineral grade distribution shall meet the requirements of Table 1. […]

6 Inspection rules

6.3 Sampling and batching

6.3.1 Sampling

Sampling of asphalt mixture shall meet the requirements of T 0701 in JTG E20-2011.

6.3.2 Batching

6.3.2.1 Conduct sampling and testing by batch.

6.3.2.2 For the same project, the asphalt mixture produced by the same raw materials, in the same mix ratio and the same production process shall be sampled according to the following requirements.

a) The sampling of mineral grade, asphalt binder and void ratio shall be batched according to 3000t/shift. When it is less than 3000t/shift, it shall be according to one batch;

b) The sampling of freeze-thaw splitting tensile strength ratio, dynamic stability and failure strain of low-temperature bending test shall be batched according to 10,000 t/shift. When it exceeds 3000t/shift but less than 10,000t/shift, it shall be according to one batch;

c) At least one dynamic modulus and fatigue life sampling shall be performed.

6.4 Rules for determination

When the performance of the asphalt mixture meets the requirements of 4.2.2, the batch is determined as qualified. When one item fails in the test results, it shall be determined that this batch of products are unqualified. […]

......
This preview omits tables, figures, formulas and parts of the technical clauses. The complete document — 15 pages — is available in the English PDF.

Referenced standards

Normative references

JTG E20-2011 · JTG F40-2004 · JTG E60-2008

Similar standards

How to Download GB/T 36143-2018

  1. 1

    Add to cart

    Click "Download PDF" on this page and choose "Buy this standard". You can add more standards before checkout.

  2. 2

    Checkout

    Enter your email and billing details. Payment is processed securely by Stripe (cards or bank transfer). Prefer bank details? Request a quotation (min. order $300).

  3. 3

    Fast delivery

    After payment you'll receive an email confirmation. The English PDF is sent to the same address, usually within minutes and at the latest within 1 business day.

  4. 4

    Invoice included

    A tax invoice is attached to the confirmation email. Need a custom invoice? Contact us.

Related Standards

English PDF
15 pages
Fast delivery
Invoice included
View Cart

Secure payment via Stripe

Payments accepted

VisaMastercardAmerican ExpressApple PayGoogle PayStripe

GB/T 36143-2018

$115.00