GB/T 35887-2018Analysis method of white granulated sugar (English PDF)
白砂糖试验方法
This is a limited preview
Buy now to download the full PDF (15 pages)
Need quotation for your management?
Get a formal quotation for GB/T 35887-2018 in 30 minutes.
Issued by
SAMR; SAC
Level / Type
National · Recommended
Issue date
February 6, 2018
Implementation date
September 1, 2018
Scope
GB/T 35887-2018 is the English-translated version of 白砂糖试验方法.
GB/T 35887-2018 gives the test methods for white granulated sugar produced from sugar cane, sugar beet or raw sugar. It covers particle size, sucrose, reducing sugar, conductivity ash, loss on drying, colour value, turbidity, water-insoluble impurities and black specks.
For particle size, a 100.0 g sample is shaken for 10 minutes through a stack of test sieves with apertures from 0.14 mm to 2.50 mm on a vibrating sieve shaker, and the sugar retained on each sieve is weighed to 0.1 g to give the mass percentage between two apertures.
Each method sets out its principle, instruments, procedure and the way results are calculated and reported. Sugar producers and quality control laboratories use it to check white sugar. It was issued on 6 February 2018 and has applied since 1 September 2018.
Found what you need?
Document preview — GB/T 35887-2018
National Standard of the People's Republic of China
- ICS
- 67.180
- Classification
- X 30
Issued by: State Administration for Market Regulation; Standardization Administration of the PRC
Contents
- Foreword
- 1 Scope
- 2 Normative references
- 3 Granularity
Foreword
This standard was drafted in accordance with the rules given in GB/T 1.1-2009.
1 Scope
This standard specifies the size of granulated sugar, sucrose, reducing sugar, conductivity ash, loss on drying, color value, turbidity, insoluble in water impurities and Black point test method.
This standard applies to white sugar produced from sugar cane, sugar beet or raw sugar in the sugar industry.
2 Normative references
The following documents are indispensable for the application of this document. For dated references, only dated versions apply to this document. For undated references, the latest version (including all amendments) applies to this document.
GB/T 6682 Analysis Laboratory Water Specifications and Test Methods
3 Granularity
3.1 Principle
A set of test sieves were used to screen the sugar samples under certain conditions, and the sugar samples retained in each sieve were weighed to obtain the remaining on the screen. The relationship between the percentage of sugar sample and the mesh.
3.2 Instruments and Equipment
3.2.1 Test sieve. a set of sieve holes 0.14mm~2.50mm, diameter 200mm.
3.2.2 Seismic screening machine. vibration frequency. 3000 times/min, 6000 times/min, amplitude selection. 0mm~3mm continuous adjustment, vibration mode. Continuous vibration.
3.2.3 Balance. Touch 0.1g.
3.3 Steps
3.3.1 Sampling
Samples are separated by quadruplicate method so that the number of secondary samples can meet the screening test.
3.3.2 Screening
Weigh 100.0g of white granulated sugar sample, sieve selected and weighed, stacked from bottom to top according to the mesh size, then, Place the sample in the uppermost sieve and cover it with a lid. Place the sieve on the shaker and shake it for 10 minutes. The vibration frequency and amplitude are not to be worn out. Sugar crystals prevail. After the vibration is completely stopped, the sieve is removed, and each sieve is weighed and the quality of the sample retained is accurate to 0.1 g.
3.3.3 Calculation and Result Presentation
Calculate the mass percentage of the sample retained between the two layers of sieves with corresponding pore sizes in the upper and lower limits of the particle size. The result is the upper and lower limits of the pore size and its quality. The quantity percentage indicates that the calculation result is an integer.
......
This preview omits tables, figures, formulas and parts of the technical clauses. The complete document — 15 pages — is available in the English PDF.
Referenced standards
Normative references
Similar standards
How to Download GB/T 35887-2018
- 1
Add to cart
Click "Download PDF" on this page and choose "Buy this standard". You can add more standards before checkout.
- 2
Checkout
Enter your email and billing details. Payment is processed securely by Stripe (cards or bank transfer). Prefer bank details? Request a quotation (min. order $300).
- 3
Fast delivery
After payment you'll receive an email confirmation. The English PDF is sent to the same address, usually within minutes and at the latest within 1 business day.
- 4
Invoice included
A tax invoice is attached to the confirmation email. Need a custom invoice? Contact us.
Related Standards
GB/T 6682-1992 — Water for analytical laboratory use--Specification and test methods
GB/T 6682-2008 — Water for analytical laboratory use - Specification and test methods
GB/T 10003-2026 — Biaxially oriented polypropylene (BOPP) film
GB/T 35887-2018
$235.00