GB/T 34611-2017Rigid polyurethane spray polyethylene winding prefabricated directly buried insulating pipes (English PDF)
硬质聚氨酯喷涂聚乙烯缠绕预制直埋保温管
This is a limited preview
Buy now to download the full PDF (15 pages)
Need quotation for your management?
Get a formal quotation for GB/T 34611-2017 in 30 minutes.
Issued by
SAMR; SAC
Level / Type
National · Recommended
Issue date
October 14, 2017
Implementation date
September 1, 2018
Scope
GB/T 34611-2017 is the English-translated version of 硬质聚氨酯喷涂聚乙烯缠绕预制直埋保温管.
GB/T 34611-2017 is the Chinese standard "Rigid polyurethane spray polyethylene winding prefabricated directly buried insulating pipes".
Its scope clause reads: This standard specifies the terms and definitions, product structure, general requirements, requirements, test methods, inspection rules, markings, transportation and storage of rigid polyurethane spray polyethylene winding prefabricated directly buried insulating pipe produced by polyurethane spraying process and polyethylene winding process (referred to as spraying and winding insulating pipe).
This standard is applicable to the manufacturing and inspection of rigid polyurethane spray polyethylene winding prefabricated directly buried insulating pipes with a medium temperature (long-term operating temperature) not exceeding 120°C and occasional peak temperature not exceeding 140°C. Its clauses include terms and definitions.
Found what you need?
Document preview — GB/T 34611-2017
National Standard of the People's Republic of China
- ICS
- 91.140.10
Issued by: State Administration for Market Regulation; Standardization Administration of the PRC
Contents
- Foreword i
- 1 Scope
- 2 Normative references
- 3 Terms and definitions
- 4 Product structure
- 5 General requirements
- 6 Requirements
- 7 Test methods
- 8 Inspection rules
- 9 Marking, transportation, and storage
- Annex A (Normative) Inspection method for circumferential thermal reversion of out casing
- Annex B (Normative) Inspection method for circumferential shrinkage of out casing
1 Scope
This standard specifies the terms and definitions, product structure, general requirements, requirements, test methods, inspection rules, markings, transportation and storage of rigid polyurethane spray polyethylene winding prefabricated directly buried insulating pipe produced by polyurethane spraying process and polyethylene winding process (referred to as spraying and winding insulating pipe).
This standard is applicable to the manufacturing and inspection of rigid polyurethane spray polyethylene winding prefabricated directly buried insulating pipes with a medium temperature (long-term operating temperature) not exceeding 120°C and occasional peak temperature not exceeding 140°C.
2 Normative references
The following referenced documents are indispensable for the application of this document. For dated references, only the edition cited applies. For undated references, the latest edition of the referenced document (including any amendments) applies.
GB/T 3091 Welded steel pipes for low pressure liquid delivery
GB/T 6671 Thermoplastics pipes - Determination of longitudinal reversion
GB/T 8163 Seamless steel tubes for liquid service
GB/T 8923.1-2011 Preparation of steel substrates before application of paints and related products - Visual assessment of surface cleanliness - Part 1: Rust grades and preparation grades of uncoated steel substrates and of steel substrates after overall removal of previous coatings
GB/T 9711 Petroleum and natural gas industries - Steel pipe for pipeline transportation systems
GB/T 18475-2001 Thermoplastics materials for pipes and fittings for pressure applications - Classification and designation - Overall service (design) coefficient
GB/T 29046-2012 Test methods of technical specification for pre-insulated directly buried district heating pipes
GB/T 29047 Prefabricated directly buried insulating pipes and fittings with polyurethane foamed-plastics and high density polyethylene casing pipes
CJJ/T 254-2016 Technical specification for leakage surveillance system of directly buried heating pipe
3 Terms and definitions
For the purposes of this document, the following terms and definitions apply.
3.1 polyurethane spraying
process where polyurethane spraying equipment is used to continuously spray the uniformly mixed polyurethane raw materials onto the outer surface of steel pipe to form polyurethane insulating layer
3.2 polyethylene winding
process where the extrusion equipment is used to continuously wind the molten polyethylene sheet onto the outer surface of polyurethane insulating layer to form a continuous and dense polyethylene out casing […]
......
This preview omits tables, figures, formulas and parts of the technical clauses. The complete document — 15 pages — is available in the English PDF.
Referenced standards
Similar standards
How to Download GB/T 34611-2017
- 1
Add to cart
Click "Download PDF" on this page and choose "Buy this standard". You can add more standards before checkout.
- 2
Checkout
Enter your email and billing details. Payment is processed securely by Stripe (cards or bank transfer). Prefer bank details? Request a quotation (min. order $300).
- 3
Instant delivery (0–9 sec)
Delivery is automatic: within seconds of payment you'll receive an email with a secure download link. The link stays valid for 72 hours.
- 4
Invoice included
A tax invoice is attached to the confirmation email. Need a custom invoice? Contact us.
Related Standards
GB/T 10003-2026 — Biaxially oriented polypropylene (BOPP) film
GB/T 10004-2026 — Plastic/Plastic laminated films and pouches for packaging
GB/T 10007-2026 — Rigid cellular plastics - Determination of shear properties
Secure payment via Stripe
Payments accepted
GB/T 34611-2017
$235.00