Valid

GB/T 34251-2017Test method for metal marking resistance of glazed ceramic tableware (English PDF)

日用陶瓷釉面耐金属刀叉划痕性能测试方法

Preview PDF

This is a limited preview

Buy now to download the full PDF (15 pages)

Need quotation for your management?

Get a formal quotation for GB/T 34251-2017 in 30 minutes.

Issued by

SAMR; SAC

Level / Type

National · Recommended

Issue date

September 7, 2017

Implementation date

April 1, 2018

Scope

GB/T 34251-2017 is the English-translated version of 日用陶瓷釉面耐金属刀叉划痕性能测试方法.

GB/T 34251-2017 is the Chinese standard "Test method for metal marking resistance of glazed ceramic tableware". Its scope clause reads: This Standard specifies the test method of determining the metal marking resistance of glazed ceramic tableware at room temperature.

This Standard is applicable to glazed plate products that are in contact with metal cutlery, such as: daily-use porcelain, stoneware and pottery, etc. Its clauses include principle; reagent; equipment and appliances; specimen; procedures; grading of scratch resistance performance; inspection report.

It was issued by the General Administration of Quality Supervision, Inspection and Quarantine of the People's Republic of China on SEPTEMBER 7, 2017 and took effect on APRIL 1, 2018.

Found what you need?

Document preview — GB/T 34251-2017

National Standard of the People's Republic of China

ICS
81.060.20
Classification
Y 24

Issued by: State Administration for Market Regulation; Standardization Administration of the PRC

Contents

  • Foreword3
  • 1 Scope4
  • 2 Normative References4
  • 3 Principle4
  • 4 Reagent4
  • 5 Equipment and Appliances4
  • 6 Specimen6
  • 7 Procedures6
  • 8 Grading of Scratch Resistance Performance6
  • 9 Inspection Report7

1 Scope

This Standard specifies the test method of determining the metal marking resistance of glazed ceramic tableware at room temperature.

This Standard is applicable to glazed plate products that are in contact with metal cutlery, such as: daily-use porcelain, stoneware and pottery, etc.

2 Normative References

The following documents are indispensable to the application of this document. In terms of references with a specified date, only versions with a specified date are applicable to this document. In terms of references without a specified date, the latest version (including all the modifications) is applicable to this document.

GB/T 1220 Stainless Steel Bars

GB/T 3280 Cold Rolled Stainless Steel Plate, Sheet and Strip

3 Principle

Simulate the mode of using a table knife, adopt a standard cutting tool to scratch the ceramic glaze back and forth in a straight line under a specific force, observe the severity of the scratch on the glaze, and determine its scratch resistance to metal tableware.

4 Reagent

Absolute ethanol (chemically pure).

5 Equipment and Appliances

5.1 Scratch Resistance Performance Tester

As it is shown in Figure 1. The temperature is controlled within ± 5°C.

5.4 Balance

The accuracy is 0.1 g.

6 Specimen

Take the plate products of the same production batch specification and the same type of ware.

The surface of the sample shall be free from defects, such as: cracks, lack of glaze and thin glaze, etc.

7 Procedures

7.1 Use sponge or cotton cloth dipped in absolute ethanol to wipe the glazed surface of the sample, then, use tap water to rinse it and use a dry cloth to dry it. At 105 °C ± 5 °C, dry it in a drying oven. Take it out, then cool it to room temperature.

7.2 Horizontally place the sample on the working platform, select a suitable scratching position (for example, the part where the table knife is often used), adjust the fastening pressure bar to compress the sample, ensure that the sample will not be loosened during the test.

7.3 Clamp the standard cutting tool, make the tool face perpendicular to the ceramic glaze. The tool edge is in parallel contact with the glaze.

7.4 Adjust the balance weight, so that the tool edge is just in contact with the glaze without any applied force.

7.5 Load the counterweight, so that the force of the cutting tool acting on the glaze is 10 N.

7.6 Turn on the power switch and carry out the scratching test. Make 3 scratches on each sample, and for each scratch, scratch for 4 times (one back and forth cycle of the cutting tool is recorded as 2 times of scratch). The parallel interval between the scratches is 10 mm.

7.7 After scratching, turn off the power switch and loosen the fastening pressure bar; remove the sample and use absolute ethanol to wipe it.

7.8 Under natural light or artificial lighting conditions, at a distance of about 25 cm from the glazed surface, conduct visual inspection.

8 Grading of Scratch Resistance Performance

From the three scratches, select two with similar degrees to conduct the determination in accordance with Table 1. […]

......
This preview omits tables, figures, formulas and parts of the technical clauses. The complete document — 15 pages — is available in the English PDF.

Referenced standards

Similar standards

How to Download GB/T 34251-2017

  1. 1

    Add to cart

    Click "Download PDF" on this page and choose "Buy this standard". You can add more standards before checkout.

  2. 2

    Checkout

    Enter your email and billing details. Payment is processed securely by Stripe (cards or bank transfer). Prefer bank details? Request a quotation (min. order $300).

  3. 3

    Fast delivery

    After payment you'll receive an email confirmation. The English PDF is sent to the same address, usually within minutes and at the latest within 1 business day.

  4. 4

    Invoice included

    A tax invoice is attached to the confirmation email. Need a custom invoice? Contact us.

Related Standards

English PDF
15 pages
Fast delivery
Invoice included
View Cart

Secure payment via Stripe

Payments accepted

VisaMastercardAmerican ExpressApple PayGoogle PayStripe

GB/T 34251-2017

$90.00