GB/T 3390.5-2013Hand operated socket wrenches - Inspection,packaging and marking (English PDF)
手动套筒扳手 检验规则、包装与标志
This is a limited preview
Buy now to download the full PDF (15 pages)
Need quotation for your management?
Get a formal quotation for GB/T 3390.5-2013 in 30 minutes.
Issued by
SAMR; SAC
Level / Type
National · Recommended
Issue date
November 12, 2013
Implementation date
May 1, 2014
Scope
GB/T 3390.5-2013 is the English-translated version of 手动套筒扳手 检验规则、包装与标志.
This standard fixes the inspection, packaging and marking of hand operated socket wrenches. Clause 1 states that it specifies the inspection rules, the packaging and the marking for them and that it applies to the hand wrenches used to assemble and dismantle hexagonal bolts and nuts.
It is the fifth item of the GB/T 3390 series, whose other parts cover the socket, the square drive and square hole, the drive accessories and the connection accessories of hand socket wrenches.
Clause 3, inspection rules, opens with 3.1 delivery inspection, which requires every product to be inspected before it leaves the factory and to go out with a product certificate, draws the delivery inspection items from the sampling plan of GB/T 2828.1, allows a test sample to be made up of items of one specification or of a whole set, and puts the classification of substandard products, the test items, the acceptance quality limit and the inspection level into Table 1, whose values are the AQLs 2.5 and 6.5 and the inspection levels S-2 and S-3 against items such as socket dimensions, the torque of socket and accessories, hardness, the fit of the square drive in the square hole, operating performance and surface quality.
The same subclause lets a rejected product be repaired and reclassified before being resubmitted for acceptance, has the delivery party replace samples found nonconforming, and requires the whole batch of a component to be re-inspected when that component fails in a suite of products.
The draft breaks off after 3.1.7, so the type test, the packaging and the marking are not shown, although the foreword places the type test at 3.2 and the product marking requirements at 4.1 and names both, together with an adjustment of the test items in Table 1, as the main technical changes against the 2004 edition.
Clause 2 cites GB/T 2828.1, GB/T 2829 and GB/T 5305. The foreword also records GB/T 3390.5-1982 and GB/T 3390.5-1989 among the editions this standard replaces, and the page lists the 1989 and 2004 editions as obsolete.
It replaces GB/T 3390.5-2004, was issued on 2013-11-12 and has applied since 2014-05-01.
Found what you need?
Document preview — GB/T 3390.5-2013
National Standard of the People's Republic of China
- ICS
- 25.140.30
- Classification
- J 47
- Replacing
- GB/T 3390.5-2004
Issued by: State Administration for Market Regulation; Standardization Administration of the PRC
Contents
- Foreword
- 1 Scope
- 2 Normative references
- 3 Inspection rules
Foreword
GB/T 3390 "Manual socket wrench," the national standard for the series, is composed of five standard components.
--- GB/T 3390.1 Manual socket wrench socket;
--- GB/T 3390.2 manual transmission mortise and tenon and socket wrenches square hole;
--- GB/T 3390.3 manual transmission accessory socket wrenches;
--- GB/T 3390.4 manual socket wrenches connection accessories;
--- GB/T 3390.5 manual socket wrenches inspection rules, packaging and marking.
This standard GB/T 3390 Item 5.
This standard was drafted in accordance with GB/T 1.1-2009 given rules.
This standard replaces GB/T 3390.5-2004 "Manual socket wrench inspection rules, packaging and marking" and GB/T 3390.5-2004 Compared to the main technical content changes are as follows.
--- Of test items have been adjusted (2004 edition Table 1, Table 1 edition);
--- Increasing the type test (edition 3.2);
--- Increased product marking requirements (edition 4.1).
The standard proposed by China National Light Industry Council.
This standard replaces the standards previously issued as follows.
--- GB/T 3390.5-1982, GB/T 3390.5-1989, GB/T 3390.5-2004.
1 Scope
This standard specifies the inspection rules manual socket wrench, packaging and marking.
This standard applies to detachable hexagonal bolts and nuts manual wrench.
2 Normative references
The following documents for the application of this document is essential. For dated references, only the dated version suitable for use herein Member. For undated references, the latest edition (including any amendments) applies to this document.
GB/T 2828.1 Sampling procedures for inspection - Part 1. by acceptance quality limit (AQL) retrieval batch inspection sampling plan (GB/T 2828.1-2012, ISO 2859-1:1999, IDT)
GB/T 2829 periodic inspection Sampling procedures and tables (suitable for process stability test)
GB/T 5305 Hand tools, packaging, labeling, transportation and storage
3 Inspection rules
3.1 Delivery inspection
3.1.1 All products must be inspected before leaving the factory after factory, along with product certification.
3.1.2 delivery inspection items by sub-sampling program GB/T 2828.1 provisions one by one.
3.1.3 The test sample may be composed of the same specifications, but also by a whole set of products.
3.1.4 Classification substandard products, test items, acceptance quality limit (AQL) and check the level specified in Table 1.
Table 1 failure classification, test items, the reception quality limit (AQL) and inspection level
No. substandard classification test items. Acceptable quality level (AQL). Inspection level (IL).
The size of the sleeve on the side; Sleeve and accessory torque; Sleeve hardness and accessories. AQL 2.5. Inspection level S-3, S-2.
Sleeve basic dimensions and accessories; Binding properties Driving square with square hole; Operating performance; Sleeve surface quality and Accessories. AQL 6.5. Inspection level S-3.
3.1.5 the inspection found nonconforming product samples and conduct post-failure test, delivery party should be replaced.
3.1.6 Upon examination of rejected product, the manufacturer may be reclassified after repair, and then submit acceptance.
3.1.7 inspection batch by the suite of products consisting of any one component in the test was sentenced to be ineligible, should all inspection installment of the component into the Repair or replace the line after re-inspection.
......
This preview omits tables, figures, formulas and parts of the technical clauses. The complete document — 15 pages — is available in the English PDF.
Referenced standards
Normative references
- GB/T 2828.1Sampling procedures for inspection by attributes - Part 1: Sampling schemes indexed by acceptance quality limit (AQL) for lot-by-lot inspection
- GB/T 2829Sampling procedures and tables for periodic inspection by attributes
- GB/T 5305Packaging, marking, transportation and storage of hand tools
Similar standards
Editions of GB/T 3390.5
| Edition | Title | Revision | Status |
|---|---|---|---|
| GB/T 3390.5-2013 | Hand operated socket wrenches - Inspection,packaging and marking | current edition | Current |
| GB/T 3390.5-2004 | Hand operated socket wrenches - Inspection,packaging and marking | previous edition | Superseded |
This page sells the current edition, GB/T 3390.5-2013. Earlier editions are listed for reference only.
How to Download GB/T 3390.5-2013
- 1
Add to cart
Click "Download PDF" on this page and choose "Buy this standard". You can add more standards before checkout.
- 2
Checkout
Enter your email and billing details. Payment is processed securely by Stripe (cards or bank transfer). Prefer bank details? Request a quotation (min. order $300).
- 3
Instant delivery (0–9 sec)
Delivery is automatic: within seconds of payment you'll receive an email with a secure download link. The link stays valid for 72 hours.
- 4
Invoice included
A tax invoice is attached to the confirmation email. Need a custom invoice? Contact us.
Related Standards
GB/T 2828.1-2012 — Sampling procedures for inspection by attributes - Part 1: Sampling schemes indexed by acceptance quality limit (AQL) for lot-by-lot inspection
GB/T 2828.10-2010 — Sampling procedures for inspection by attributes -- Part 10: Introduction to the GB/T 2828 series of standards for sampling for inspection by attributes
GB/T 2828.11-2008 — Sampling procedures for inspection by attributes Part 11: Procedures for assessment of declared quality levels for small population
Secure payment via Stripe
Payments accepted
GB/T 3390.5-2013
$75.00