GB/T 32515-2016Variable-frequency drive for injection molding machine (English PDF)
注塑机专用变频调速设备
This is a limited preview
Buy now to download the full PDF (24 pages)
Need quotation for your management?
Get a formal quotation for GB/T 32515-2016 in 30 minutes.
Issued by
SAMR; SAC
Level / Type
National · Recommended
Issue date
February 24, 2016
Implementation date
September 1, 2016
Scope
GB/T 32515-2016 is the English-translated version of 注塑机专用变频调速设备.
GB/T 32515-2016 is the Chinese standard "Variable-frequency drive for injection molding machine". Its scope clause reads: The standard provides for plastic injection molding special inverter device classification, conditions of use, technical requirements, test items and signs, packaging, transportation and storage.
This standard applies to the rated input voltage of AC 1kV and below grade, rated input frequency of 50Hz or 60Hz, the output voltage is less than 1kV, the output frequency is less than 600Hz injection molding machine frequency control device (hereinafter referred to as "Speed Device"). Its clauses include terms and definitions.
Found what you need?
Document preview — GB/T 32515-2016
National Standard of the People's Republic of China
- ICS
- 29.240.99
- Classification
- K 46
Issued by: State Administration for Market Regulation; Standardization Administration of the PRC
Contents
- Introduction III
- 1 Scope 1
- 2 Normative references 1
- 3 Terms and definitions
- 4 Category 4
- 5 Rating 4
- 5.1 input side Rating 4
- 5.2 Output Rating 5
- 6 Conditions 5
- 6.1 Environmental conditions 5
- 6.2 Electrical conditions 6
- 7 Technical requirements 7
- 7.1 7 ... appearance and mechanical properties
- 7.2 Functional requirements 8
- 7.3 Safety Requirements 8
- 7.4 rated output capacity 12
- 7.5 light load operation 12
- 7.6 operating frequency range of technical performance 12
- 7.7 Efficiency 13
- 7.8 The total input power factor 13
- 7.9 Output voltage unbalance 13
- 7.10 Protection 13
- 7.11 temperature 14
- 7.12 Noise 14
- 7.13 environmental adaptability 14
- 7.14 Electromagnetic compatibility 14
- 7.15 braking capacity 14
- 7.16 Built-in pressure regulator 15
- 8 Test 15
- 8.1 General requirements 15
- 8.2 Type tests 15
- 8.3 factory test 15
- 8.5 Test Project 15
- 8.6 General inspection 16
- 8.7 Insulation System Test 16
- 8.8 clearances and creepage distances 16
- 8.9 grounding continuity protection 16
- 8.10 rated output capacity 17
- 8.11 light-load running test 17
- 8.13 Efficiency measuring 18
- 8.14 input power factor measurement 18
- 8.15 temperature rise test 18
- 8.16 Noise Measurement 18
- 8.18 output voltage unbalance measuring 18
- 8.19 overload test 18
- 8.20 Protection 18
- 8.21 18 ... environmental adaptability test
- 8.22 Electromagnetic compatibility test 18
- 8.23 Protection class test 19
- 8.24 to discharge the capacitor 19
- 9 signs, packaging, transportation and storage 19
- 9.1 mark 19
- 9.2 Packaging 19
- 9.3 Transport 19
- 9.4 Storage 19
- Appendix A (normative) electromagnetic compatibility requirements 21
1 Scope
The standard provides for plastic injection molding special inverter device classification, conditions of use, technical requirements, test items and signs, packaging, transportation and storage.
This standard applies to the rated input voltage of AC 1kV and below grade, rated input frequency of 50Hz or 60Hz, the output voltage is less than 1kV, the output frequency is less than 600Hz injection molding machine frequency control device (hereinafter referred to as "Speed Device").
2 Normative references
The following documents for the application of this document is essential. For cited documents with dates, only the dated edition applies to this document. For undated references, the latest edition (including any amendments) applies to this document.
GB/T 2900.1-2008 Electrical Basic terminology
GB/T 2900.33-2004 Electrotechnical terminology - Power Electronics
GB/T 2900.83-2008 Electrotechnical terminology of electrical and magnetic devices
GB/T 3797 Electric Control Equipment
GB 4208-2008 shell protection (IP code)
GB/T 4798.2-2008 application of electric and electronic products environmental conditions - Part 2. Transport
GB/T 4798.3-2007 application of electric and electronic products environmental conditions - Part 3. Stationary use at weather protected locations
GB 12668.3-2012 speed electric drive systems - Part 3. EMC requirements and specific test methods
GB/T 12668.501-2013 speed electric drive systems - Part 5-1. Safety requirements for electrical, thermal and energy
GB/T 13384-2008 mechanical and electrical products packaging General technical conditions
GB/T 17626.2-2006 Electromagnetic compatibility - Testing and measurement techniques - Electrostatic discharge immunity test
GB/T 17626.3-2006 Electromagnetic compatibility - Testing and measurement techniques RFEMS test
GB/T 17626.4-2008 Electromagnetic compatibility - Testing and measurement techniques - Electrical fast transient burst immunity test
GB/T 17626.5-2008 Electromagnetic compatibility - Testing and measurement techniques - Surge (impact) immunity test
GB/T 17626.6-2008 Electromagnetic compatibility - Testing and measurement techniques Immunity to conducted disturbances induced field
GB/T 17627.1-1998 part of high-voltage test techniques for low voltage equipment. Definitions and testing requirements
GB/Z 18039.5-2003 electromagnetic compatibility environment in public power supply system frequency conducted disturbances and signaling in the electromagnetic environment
GB 23712-2009 Industry machinery electrical equipment, machine tools EMC emission limits
GB/T 30844.2-2014 1kV and the following general frequency control equipment - Part 2. Test methods
IEC 61000-2-4.2002 Electromagnetic compatibility (EMC) - Part 2-4. Environmental plant frequency conducted disturbances compatibility level
3 Terms and Definitions
GB/T 2900.1-2008, GB/T 2900.33-2004, GB/T 2900.83-2008 defined and the following terms and definitions apply to this document.
......
This preview omits tables, figures, formulas and parts of the technical clauses. The complete document — 24 pages — is available in the English PDF.
Similar standards
How to Download GB/T 32515-2016
- 1
Add to cart
Click "Download PDF" on this page and choose "Buy this standard". You can add more standards before checkout.
- 2
Checkout
Enter your email and billing details. Payment is processed securely by Stripe (cards or bank transfer). Prefer bank details? Request a quotation (min. order $300).
- 3
Instant delivery (0–9 sec)
Delivery is automatic: within seconds of payment you'll receive an email with a secure download link. The link stays valid for 72 hours.
- 4
Invoice included
A tax invoice is attached to the confirmation email. Need a custom invoice? Contact us.
Related Standards
GB/T 10003-2026 — Biaxially oriented polypropylene (BOPP) film
GB/T 10004-2026 — Plastic/Plastic laminated films and pouches for packaging
GB/T 10007-2026 — Rigid cellular plastics - Determination of shear properties
Secure payment via Stripe
Payments accepted
GB/T 32515-2016
$415.00