Valid

GB/T 32505-2016Variable-frequency drive for machine tool (English PDF)

机床专用变频调速设备

Preview PDF

This is a limited preview

Buy now to download the full PDF (20 pages)

Need quotation for your management?

Get a formal quotation for GB/T 32505-2016 in 30 minutes.

Issued by

SAMR; SAC

Level / Type

National · Recommended

Issue date

February 24, 2016

Implementation date

September 1, 2016

Scope

GB/T 32505-2016 is the English-translated version of 机床专用变频调速设备.

GB/T 32505-2016 is the Chinese standard "Variable-frequency drive for machine tool". Its scope clause reads: This standard specifies the machine-specific frequency control device design, application conditions, technical requirements, testing and judgment, packaging and storage.

This standard applies to the rated input voltage of AC 1kV and below grade, rated input frequency of 50Hz or 60Hz, the output voltage is less than 1kV, the output frequency is less than 600Hz machine with frequency control device (hereinafter referred to as "Speed Device").

Found what you need?

Document preview — GB/T 32505-2016

National Standard of the People's Republic of China

ICS
29.240.99
Classification
K 46

Issued by: State Administration for Market Regulation; Standardization Administration of the PRC

Contents

  • Introduction III
  • 1 Scope 1
  • 2 Normative references 1
  • 3 Terms and definitions 2
  • 5 Rating 4
  • 5.1 General requirements 4
  • 5.2 input side Rating 4
  • 5.3 Output Rating 4
  • 6 Conditions 4
  • 6.1 Environmental conditions 4
  • 6.2 Electrical conditions 6
  • 7 Technical requirements 7
  • 7.1 7 ... appearance and mechanical properties
  • 7.2 Functional requirements 7
  • 7.3 Safety Requirements 7
  • 7.4 rated output capacity 9
  • 7.5 light load operation 9
  • 7.7 Efficiency 10
  • 7.8 The total input power factor 10
  • 7.9 Temperature Rise 10
  • 7.10 noise requirements 11
  • 7.11 output voltage unbalance 11
  • 7.13 Protection 11
  • 7.14 braking capacity 11
  • 7.15 environmental adaptability 12
  • 7.16 Electromagnetic compatibility 12
  • 8 Test 12
  • 8.1 General Requirements 12
  • 8.2 Type tests 12
  • 8.3 factory test 12
  • 8.5 Test item 12
  • 8.6 General inspection 13
  • 8.7 Functional requirements 13
  • 8.8 Electrical Safety 13
  • 8.9 rated output capacity of 13
  • 8.10 light-load test 13
  • 8.11 within the operating frequency range of technical performance measurement 14
  • 8.12 14 ... efficiency measurement
  • 8.13 power factor measurement 14
  • 8.14 temperature rise test 14
  • 8.15 Noise Measurement 14
  • 8.17 output voltage unbalance 15
  • 8.19 Protection 15
  • 8.20 Determination of braking capacity 15
  • 8.21 15 ... environmental adaptability test
  • 8.22 Electromagnetic compatibility test 16
  • 9 signs, packaging, transportation and storage 16
  • 9.1 mark 16
  • 9.2 Packaging 16
  • 9.3 Transport 16
  • 9.4 Storage 17
  • Appendix A (normative) electromagnetic compatibility requirements 18
  • References 21

1 Scope

This standard specifies the machine-specific frequency control device design, application conditions, technical requirements, testing and judgment, packaging and storage.

This standard applies to the rated input voltage of AC 1kV and below grade, rated input frequency of 50Hz or 60Hz, the output voltage is less than 1kV, the output frequency is less than 600Hz machine with frequency control device (hereinafter referred to as "Speed Device").

2 Normative references

The following documents for the application of this document is essential. For cited documents with dates, only the dated edition applies to this document. For undated references, the latest edition (including any amendments) applies to this document.

GB/T 3797 Electric Control Equipment

GB 4208-2008 shell protection (IP code)

GB/T 4798.2-2008 application of electric and electronic products environmental conditions - Part 2. Transport

GB/T 4798.3-2007 application of electric and electronic products environmental conditions - Part 3. Stationary use at weather protected locations

GB 4824-2013 industrial, scientific and medical (ISM) radio frequency equipment disturbance characteristics - Limits and methods of measurement

GB 5226.1-2008 Safety of machinery - Electrical machinery and electrical equipment - Part 1. General requirements

GB/T 12668.2-2002 speed electric drive systems - Part 2. General requirements for low-voltage adjustable frequency ac power drive systems rating requirements (IEC 61800-2.1998, IDT)

EMC requirements and specific test methods. Part 3 GB 12668.3-2012 speed electric drive systems (IEC 61800-3.2004, IDT)

GB 12668.501-2013 speed electric drive systems - Part 5-1. Safety requirements for electrical, thermal and energy

GB/T 13384-2008 mechanical and electrical products packaging General technical conditions

GB/T 17626.2-2006 Electromagnetic compatibility - Testing and measurement techniques - Electrostatic discharge immunity test

GB/T 17626.3-2006 Electromagnetic compatibility - Testing and measurement techniques RFEMS test

GB/T 17626.4-2008 Electromagnetic compatibility - Testing and measurement techniques - Electrical fast transient burst immunity test

GB/T 17626.5-2008 Electromagnetic compatibility - Testing and measurement techniques - Surge (impact) immunity test

GB/T 17626.6-2008 Electromagnetic compatibility - Testing and measurement techniques Immunity to conducted disturbances induced field

GB/T 17626.8-2006 Electromagnetic compatibility - Testing and measurement techniques - Power frequency magnetic field immunity test

GB/T 17627.1-1998 high voltage test techniques for low voltage equipment Part I. Definitions and testing requirements

GB /Z18039.5-2003 electromagnetic compatibility environment in public power supply system frequency conducted electromagnetic environment harassment and signal transmission

GB/T 22663-2008 industrial machinery and electrical equipment EMC immunity requirements for machine tools

GB 23712-2009 Industry machinery electrical equipment, machine tools EMC emission limits

GB/T 30844.1-2014 1kV and the following general frequency control equipment - Part 1. Technical conditions

GB/T 30844.2-2014 1kV and the following general frequency control equipment - Part 2. Test methods

IEC 61000-2-4.2002 Electromagnetic compatibility (EMC) - Part 2-4. Environmental plant frequency conducted disturbances compatibility level […]

......
This preview omits tables, figures, formulas and parts of the technical clauses. The complete document — 20 pages — is available in the English PDF.

Similar standards

How to Download GB/T 32505-2016

  1. 1

    Add to cart

    Click "Download PDF" on this page and choose "Buy this standard". You can add more standards before checkout.

  2. 2

    Checkout

    Enter your email and billing details. Payment is processed securely by Stripe (cards or bank transfer). Prefer bank details? Request a quotation (min. order $300).

  3. 3

    Fast delivery

    After payment you'll receive an email confirmation. The English PDF is sent to the same address, usually within minutes and at the latest within 1 business day.

  4. 4

    Invoice included

    A tax invoice is attached to the confirmation email. Need a custom invoice? Contact us.

Related Standards

English PDF
20 pages
Fast delivery
Invoice included
View Cart

Secure payment via Stripe

Payments accepted

VisaMastercardAmerican ExpressApple PayGoogle PayStripe

GB/T 32505-2016

$355.00