Valid

GB/T 28878.10-2019Specification of the rotating component in space science experiments—Part 10: Storage and reinspection (English PDF)

空间科学实验转动部件规范第10部分：储存复验

Preview PDF

This is a limited preview

Buy now to download the full PDF (15 pages)

Need quotation for your management?

Get a formal quotation for GB/T 28878.10-2019 in 30 minutes.

Issued by

SAMR; SAC

Level / Type

National · Recommended

Issue date

June 4, 2019

Implementation date

October 1, 2019

Scope

GB/T 28878.10-2019 is the English-translated version of 空间科学实验转动部件规范第10部分：储存复验.

GB/T 28878.10-2019 is Part 10 of GB/T 28878 and specifies how rotating components used in space science experiments are stored and re-inspected, and how the data collected after storage are analysed and evaluated.

For ground storage it fixes a temperature of 20 °C ± 10 °C, an air pressure of 86 kPa to 106 kPa, a relative humidity of 30% to 50% and ISO level-8 cleanliness to GB/T 25915.1-2010; for in-orbit storage it recommends keeping grease-lubricated components above -10 °C. It sets the reinspection cycle, every 6 months during the ground storaging term, and defines that term and the parallel storage specimen kept alongside the product.

It applies at component and complete-machine level, and rotating components of other payloads and spacecraft platforms may refer to it. It was issued on 4 June 2019 and has applied since 1 October 2019.

Found what you need?

Document preview — GB/T 28878.10-2019

National Standard of the People's Republic of China

ICS: 49.035
Classification: V 22

Issued by: State Administration for Market Regulation; Standardization Administration of the PRC

Foreword3
1 Scope4
2 Normative references4
3 Terms and definitions5
4 Storage conditions5
5 Reinspection5
6 Data analysis and evaluation7

1 Scope

This Part of GB/T 28878 specifies the storage conditions and reinspection methods of rotating component in space science experiments under specified conditions, as well as data analysis and evaluation after storage. Among them, if there are special requirements for the environmental conditions of storage and reinspection in the contract or technical requirements, it shall be implemented in accordance with the contract or technical requirements.

This Part applies to the storage and reinspection of rotating component in space science experiments at the component level and the complete-machine level.

The storage and reinspection of rotating component of other payloads and spacecraft platforms in the corresponding state can refer to it for use.

2 Normative references

The following documents are indispensable for the application of this document.

For dated references, only the dated version applies to this document. For undated references, the latest edition (including all amendments) applies to this document.

GB/T 14481-2008, Test procedure for single-phase synchronous machines

GB/T 20638-2006, General specification for stepping motors

GB/T 25915.1-2010, Cleanrooms and associated controlled environments. Part 1: Classification of air cleanliness

GB/T 28878.1, Specification of the rotating component in space science experiments. Part 1: General requirements of design

GB/T 28878.6-2016, Specification of the rotating component in space science experiments. Part 6: Property testing

3 Terms and definitions

Terms and definitions determined by GB/T 28878.1 and the following ones are applicable to this document.

3.1 Storaging term

The term of storage under certain environmental conditions from the completion of the production and delivery to the start of use.

3.2 Parallel storage specimen

The test specimen that is stored synchronously with the product in order to simultaneously grasp the key characteristic parameters of the product sensitive to the storage environment and storage life, in the process of product storage.

4 Storage conditions

4.1 Ground storage environmental conditions

The ground storage environment shall meet the following requirements:

a) temperature: 20°C ± 10°C;

b) air pressure: 86 kPa ~ 106 kPa;

c) relative humidity: 30% ~ 50%;

d) cleanliness: ISO level-8 that is required by GB/T 25915.1-2010.

4.2 In-orbit storage environmental conditions

The in-orbit storage environment shall meet the following requirements:

a) For grease-lubricated rotating component that is stored in orbit, the temperature should be above -10°C.

b) Other environmental parameters are not subject to special requirements.

5 Reinspection

5.1 Reinspection cycle

The reinspection cycle shall meet the following requirements:

a) It should be re-inspected every 6 months during the ground storaging term; […]

......
This preview omits tables, figures, formulas and parts of the technical clauses. The complete document — 15 pages — is available in the English PDF.

Referenced standards

Normative references

Similar standards

GB/T 47264-2026|GB/T 46748-2025|GB/T 43927-2024|GB/T 43366-2023|GB/T 41035-2021|GB/T 38771-2020

How to Download GB/T 28878.10-2019

1
Add to cart
Click "Download PDF" on this page and choose "Buy this standard". You can add more standards before checkout.
2
Checkout
Enter your email and billing details. Payment is processed securely by Stripe (cards or bank transfer). Prefer bank details? Request a quotation (min. order $300).
3
Instant delivery (0–9 sec)
Delivery is automatic: within seconds of payment you'll receive an email with a secure download link. The link stays valid for 72 hours.
4
Invoice included
A tax invoice is attached to the confirmation email. Need a custom invoice? Contact us.