Valid

GB/T 25350-2010Technology specification for cleaning fuel supply system of ethanol gasoline vehicles (English PDF)

使用乙醇汽油车辆燃油供给系统清洗工艺规范

Preview PDF

This is a limited preview

Buy now to download the full PDF (15 pages)

Need quotation for your management?

Get a formal quotation for GB/T 25350-2010 in 30 minutes.

Issued by

SAMR; SAC

Level / Type

National · Recommended

Issue date

November 10, 2010

Implementation date

March 1, 2011

Scope

GB/T 25350-2010 is the English-translated version of 使用乙醇汽油车辆燃油供给系统清洗工艺规范.

GB/T 25350-2010 is the Chinese standard "Technology specification for cleaning fuel supply system of ethanol gasoline vehicles".

Its scope clause reads: This Standard specifies the fuel supply system cleaning project and technical requirements, operation process, inspection and commissioning, quality assurance period for gasoline vehicles before they use ethanol gasoline for the first time.

This Standard is applicable to cleaning fuel supply system of ethanol gasoline vehicles which have been driving for more than 30,000 km prior to the first use of ethanol gasoline.

Its clauses include cleaning items and technical requirements; fuel tank; fuel pump; fuel filter; tubing; inspection and debugging; quality assurance period.

Found what you need?

Document preview — GB/T 25350-2010

National Standard of the People's Republic of China

ICS
03.220.20
Classification
R 16

Issued by: State Administration for Market Regulation; Standardization Administration of the PRC

Contents

  • Foreword3
  • 1 Scope4
  • 2 Cleaning items and technical requirements4
  • 3 Cleaning operation process5
  • 4 Inspection and debugging8
  • 5 Quality assurance period8

1 Scope

This Standard specifies the fuel supply system cleaning project and technical requirements, operation process, inspection and commissioning, quality assurance period for gasoline vehicles before they use ethanol gasoline for the first time.

This Standard is applicable to cleaning fuel supply system of ethanol gasoline vehicles which have been driving for more than 30,000 km prior to the first use of ethanol gasoline.

2 Cleaning items and technical requirements

See Table 1 for cleaning items and technical requirements. The process flow is shown in Figure 1.

Table 1 Cleaning items and technical requirements

No. Item Technical requirements

1 Fuel tank

a) No dirt, rust, glial particles, accumulated water in the tank;

b) Fuel tank pads are intact, fast and reliable, without wear, oil spill;

c) No dirt in tank breathing valve, easy access and easy exhaust;

d) The oil sensor float is alcohol resistant material.

2 Fuel pump

a) Clean, no impurities inside and outside of fuel pump;

b) The pump membrane is alcohol resistant material;

c) The fuel filter is clean, smooth, without dirt.

3 Fuel filter

a) Replace the disposable fuel filter;

b) No dirt inside and outside the detachable fuel filter; filter is resistant alcohol filter such as metal grid or ceramic material.

4 Injector No carbon deposition, blockage, drip oil leakage phenomenon

5 Tubing

a) Tubing is resistant to alcohol;

b) Pipeline is clean and smooth;

c) No sag, crack or leakage joints;

d) The tubing connector is alcohol resistant material.

6

Fuel evaporation control device a) Pipeline is resistant to alcohol, clean and smooth;

b) The surface of the activated carbon tank is not damaged;

c) Activated carbon is effective.

3.9 Carburetor cleaning

3.9.1

Clean the outside of the carburetor first. Then decompose the carburetor.

Clean each oil channel, measuring hole, oil room, atomizing nozzle, needle and inlet filter, etc.

3.9.2

Check oil float, plastic parts, rubber parts. If they are made of a material susceptible to ethanol corrosion, it shall be replaced with alcohol resistant parts.

3.9.3

Install the carburetor and connect the tubing.

3.10 Oil-water separator cleaning

3.10.1

Check the oil-water separator. Replace it if it cannot work as normal.

3.10.2

Clean the oil-water separator to make it without dirt or accumulated water.

4 Inspection and debugging

4.1

Check the fuel supply system. The pipeline connection shall be reliable, without leakage. The relevant parameters shall meet the original technical requirements.

4.2

Make adaptive adjustment to carburetor engine. Properly adjust the concentration of the mixture. Advance the ignition advance angle.

4.3

After adding automotive ethanol gasoline, the engine shall start with good performance, idle stability, smooth running, without broken cylinder, tempering, blasting or abnormal sound.

5 Quality assurance period

Calculated from the date of completion and exit-factory, the vehicle shall travel

2000 km or 10d, whichever comes first.

__________ END __________ […]

......
This preview omits tables, figures, formulas and parts of the technical clauses. The complete document — 15 pages — is available in the English PDF.

Similar standards

How to Download GB/T 25350-2010

  1. 1

    Add to cart

    Click "Download PDF" on this page and choose "Buy this standard". You can add more standards before checkout.

  2. 2

    Checkout

    Enter your email and billing details. Payment is processed securely by Stripe (cards or bank transfer). Prefer bank details? Request a quotation (min. order $300).

  3. 3

    Instant delivery (0–9 sec)

    Delivery is automatic: within seconds of payment you'll receive an email with a secure download link. The link stays valid for 72 hours.

  4. 4

    Invoice included

    A tax invoice is attached to the confirmation email. Need a custom invoice? Contact us.

Related Standards

English PDF
15 pages
Instant delivery (0–9 sec)
Invoice included
View Cart

Secure payment via Stripe

Payments accepted

VisaMastercardAmerican ExpressApple PayGoogle PayStripe

GB/T 25350-2010

$75.00