GB/T 24278-2019Protective clothing for professional motorcycle riders (English PDF)

Foreword

This standard was drafted in accordance with the rules given in GB/T 1.1-2009.

This standard replaces GB/T 24278-2009 "Motorcycle Protective Clothing", compared with GB/T 24278-2009, the main technical changes as follows.

--- Revised the standard applicable object (see Chapter 1, Chapter 1 of the 2009 edition);

--- Modifications supplemented with normative references (see Chapter 2, Chapter 2 of the 2009 edition);

--- Removed the term "high waist pants", "long jacket" and "motorcyclist" (see Chapter 3 of the 2009 edition);

--- Revised the definition of the term "structural strength layer" and "reflective material" (see Chapter 3, Chapter 3 of the 2009 edition);

--- Added the terms "collision area" "model" "test area" (see Chapter 3);

--- Revised the requirements for the instructions for use (see Chapter 5.1, Chapter 5.1);

--- Modified the functional level labeling content (see 5.1.1, Chapter 12 of the 2009 edition);

--- Revised the requirements for protective movement restrictions (see Chapters 5.2 and 9, Chapter 7 of the 2009 edition);

--- Revised the requirements for the position limit of the protective gear (see 5.3, 5.3 of the 2009 edition);

--- Supplemented the physical and chemical performance requirements of textile materials (see 5.5, 5.5 of the 2009 edition);

--- Supplemented the physical and chemical performance requirements of leather (see 5.6, 5.6 of the 2009 edition);

--- Revised the technical requirements for reflective materials (see Chapter 7, Chapter 8 of the 2009 edition);

--- Revised the technical requirements for design and partitioning (see Chapter 8, Chapter 9 of the 2009 edition);

--- Added detection method (see Chapter 9).

Introduction

In the event of a road traffic accident, the clothing and helmet that can be provided to the motorcyclist are mainly the clothing and helmet worn by the driver. Therefore, The protective clothing of the driver should be distinguished from the general functional clothing, which not only provides protection against the surrounding wind, water, cold, etc., but also The rider provides some protection against accidents during an accident. In addition, wearing motorcycle protective clothing should not hinder the driver from driving normally. Driving a motorcycle.

This standard is referenced in the revision of the European standard EN 13595-1:2002 "Motorcycle protective clothing jacket, pants, conjoined or divided Body Assembly Part 1. General Requirements, mainly related to the protective effect that can be provided by wearing motorcycle protective clothing during an accident.

The dangers faced by motorcyclists vary with the environment around them, such as road or mountain road conditions, climate, traffic environment, and motorcycles.

The speed of the carriage and the skill of the driver. Even if all the functions of the collection are not expected, it can cope with every kind of danger. risk. Therefore, this standard contains a single characteristic requirement or a simple compound requirement for a certain part of the garment.

1 Scope

This standard specifies the terms and definitions, functional level and zoning principles, requirements, fit and ergonomics of motorcycle protective clothing.

Application, design and zoning, inspection methods, marking, packaging, transportation and storage of reflective materials.

This standard applies to adult motorcycle hand protective clothing produced from textile materials and leather.

This standard does not apply to motorcycle hand protective clothing produced from artificial leather and synthetic leather.

2 Normative references

The following documents are indispensable for the application of this document. For dated references, only dated versions apply to this document. For undated references, the latest edition (including all amendments) applies to this document.

GB/T 1335.1 clothing number type men

GB/T 1335.2 clothing number type women

GB/T 2912.1 Determination of formaldehyde - Part 1. Free and hydrolyzed formaldehyde (water extraction method)

GB/T 3917.2 Textile fabrics - Tearing properties - Part 2: Determination of tear strength

GB/T 3920 Textile color fastness test color fastness to rubbing

GB/T 3922 Textile color fastness test color fastness to perspiration

GB/T 5713 Textile color fastness test color fastness to water

GB/T 7573 Determination of pH of textile water extracts

GB/T 8427-2008 Textile color fastness test resistance to artificial light color fastness. xenon arc

GB/T 8629-2017 Home washing and drying procedures for textile testing

GB/T 8630 Determination of dimensional changes after washing and drying of textiles

GB/T 15557 clothing terminology

GB/T 16160 Appearance dimension definition and method for clothing

GB/T 17592 Determination of banned azo dyes for textiles

GB 18401 National Textile Products Basic Safety Technical Specifications

GB/T 20097 protective clothing general requirements

GB 20400 Leather and fur hazardous substances limited

GB 20653-2006 occupational high visibility warning suit

GB/T 21294 Inspection method for physical and chemical properties of garments

GB/T 22807 Determination of hexavalent chromium content in leather and fur chemical tests

GB/T 23344 Textiles - Determination of 4-aminoazobenzene

GB/T 31127-2014 Textile color fastness test stitching and dyeing fastness

FZ/T 01031-2016 Determination of joint strength and elongation of knitted fabrics and elastic woven fabrics

FZ/T 80002 Clothing signs, packaging, transport and storage

QB/T 2262 Leather Industry Terminology

QB/T 2537 leather color fastness test reciprocating rubbing color fastness

QB/T 2711 Determination of the physical and mechanical testing of leather tearing force. bilateral tearing

QB/T 2724 Determination of pH in leather chemistry test