GB/T 23561.5-2009Methods for determining the physical and mechanical properties of coal and rock - Part 5: Methods for determining the water absorbability of coal and rock (English PDF)
煤和岩石物理力学性质测定方法 第5部分:煤和岩石吸水性测定方法
This is a limited preview
Buy now to download the full PDF (15 pages)
Need quotation for your management?
Get a formal quotation for GB/T 23561.5-2009 in 30 minutes.
Issued by
SAMR; SAC
Level / Type
National · Recommended
Issue date
April 8, 2009
Implementation date
December 1, 2009
Scope
GB/T 23561.5-2009 is the English-translated version of 煤和岩石物理力学性质测定方法 第5部分:煤和岩石吸水性测定方法.
GB/T 23561.5-2009 is the Chinese standard "Methods for determining the physical and mechanical properties of coal and rock - Part 5: Methods for determining the water absorbability of coal and rock".
Its scope clause reads: This part of GB/T 23561 specifies the terms and definitions involved in the determination method of coal and rock water absorption, the determination of natural water absorption and determination of forced water absorption.
This part is applicable to the determination of the water absorption of coal and rocks that do not disintegrate, dissolve, shrink or swell when exposed to water.
Its clauses include terms and definitions; determination of natural water absorption; determination of forced water absorption.
Found what you need?
Document preview — GB/T 23561.5-2009
National Standard of the People's Republic of China
- ICS
- 73.010
- Classification
- D 04
Issued by: State Administration for Market Regulation; Standardization Administration of the PRC
Contents
- 1 Scope
- 2 Terms and Definitions
- 3 Determination of natural water absorption
- 4 Determination of forced water absorption
1 Scope
This part of GB/T 23561 specifies the terms and definitions involved in the determination method of coal and rock water absorption, the determination of natural water absorption and determination of forced water absorption.
This part is applicable to the determination of the water absorption of coal and rocks that do not disintegrate, dissolve, shrink or swell when exposed to water.
2 Terms and Definitions
The following terms and definitions apply to this part of GB/T 23561.
3 Determination of natural water absorption
3.1 Instruments and equipment
The instruments and equipment used in the test are as follows.
a) Balance. Sensitivity (minimum division value) 0.01g;
b) oven;
c) dryer;
d) water container;
e) diamond machines, stone cutters, stone mills and grinders;
f) Vacuum pumping equipment and boiling equipment;
g) Weighing device in water;
h) Measuring platform.
3.2 Test steps
3.2.1
Select three representative approximately cubic rock blocks with a side length of about 4cm to 5cm from the samples as test pieces.
For the test piece with fixed mechanical properties, remove the sticky matter and easy-falling debris on the surface, and pay attention not to cause artificial cracks.
For soft rock and extremely soft rock, protective measures should be taken for the test piece to prevent the test piece from falling off or disintegrating during water absorption.
3.2.2
Dry the test piece in an oven at 105°C to 110°C for 24h, take out the test piece, cool it to room temperature in a desiccator, and weigh it to obtain M.
3.2.3
Place several glass rods with the same diameter in the water container, the distance between each glass rod is 1cm-2cm, and the rock blocks are placed on the glass rods.
Above, the distance between each test piece is 1cm-2cm.
3.2.4
Fill the container with water to a quarter of the height of the test piece, and then inject water every 2 hours.
The highest value is equal to a quarter of the height of the test piece until the final liquid level is 1cm to 2cm higher than the test piece.
3.2.5
After 24h, take out the test piece, wipe off the surface moisture with a wet towel, and weigh it for the first time. Put it back into the water container after weighing,
Weigh once every 24 hours until the mass difference between the two before and after does not exceed 0.01g. The last weighing is the mass of the specimen after absorbing water.
Quantity M1.
3.3 Data Calculation
According to the formula (1) to calculate the measurement result.
4 Determination of forced water absorption
4.1 Instruments and equipment
The vacuum pumping device is shown in Figure 1, and the vacuum pump is required to be able to reach 0.001MPa (about 7mmHg). Other instruments and equipment are the same as 3.1.
4.2 Test procedure
4.2.1
Preparation of test pieces and drying and weighing shall be carried out according to 3.2.1 and 3.2.2.
4.2.2
Place the dried test piece on the perforated plate in the vacuum tank, see Figure 1, and the distance should not be less than 2cm.
4.2.3
Connect the air extraction system, and all connections must be free of air leakage.
4.2.4
Start the vacuum pump, pump air for 20-30 minutes, then open the three-way valve, and slowly inject water into the vacuum pumping tank until the water surface is higher than
The test piece is 2cm-3cm, and then continue to pump until there are no more air bubbles on the surface of the test piece, and the pumping time should not be less than 4h; turn off the vacuum pump, twist
Turn the three-way valve to make the vacuum pumping tank communicate with the atmosphere.
4.2.5
The vacuum degree of pumping should be kept at 0.001MPa (about 7mmHg).
4.2.6
Take out the test piece from the vacuum pumping tank, put it in a water container whose water level exceeds the top of the test piece, and let it stand for more than 4h.
4.2.7
Take out the saturated test piece, wipe off the surface moisture with a wet towel, and weigh it to obtain M2.
4.3 Data Calculation
According to the formula (2) to calculate the measurement results.
......
This preview omits tables, figures, formulas and parts of the technical clauses. The complete document — 15 pages — is available in the English PDF.
Similar standards
How to Download GB/T 23561.5-2009
- 1
Add to cart
Click "Download PDF" on this page and choose "Buy this standard". You can add more standards before checkout.
- 2
Checkout
Enter your email and billing details. Payment is processed securely by Stripe (cards or bank transfer). Prefer bank details? Request a quotation (min. order $300).
- 3
Fast delivery
After payment you'll receive an email confirmation. The English PDF is sent to the same address, usually within minutes and at the latest within 1 business day.
- 4
Invoice included
A tax invoice is attached to the confirmation email. Need a custom invoice? Contact us.
Related Standards
GB/T 23561.6-2009 — Methods for determining the physical and mechanical properties of coal and rock - Part 6: Methods for determining the moisture content of coal and rock
GB/T 23561.4-2009 — Methods for determining the physical and mechanical properties of coal and rock - Part 4: Methods for calculating the porosity of coal and rock
GB/T 23561.7-2009 — Methods for determining the physical and mechanical properties of coal and rock - Part 7: Methods for determining the uniaxial compressive strength and counting softening coefficient
GB/T 23561.5-2009
$90.00