Valid

GB/T 23278.1-2009Methods for chemical analysis of sodium stannate - Part 1: Determination of tin content - Titration (English PDF)

锡酸钠化学分析方法 第1部分:锡量的测定 碘酸钾滴定法

Preview PDF

This is a limited preview

Buy now to download the full PDF (15 pages)

Need quotation for your management?

Get a formal quotation for GB/T 23278.1-2009 in 30 minutes.

Issued by

SAMR; SAC

Level / Type

National · Recommended

Issue date

January 5, 2009

Implementation date

November 1, 2009

Scope

GB/T 23278.1-2009 is the English-translated version of 锡酸钠化学分析方法 第1部分:锡量的测定 碘酸钾滴定法.

GB/T 23278.1-2009 is the Chinese standard "Methods for chemical analysis of sodium stannate - Part 1: Determination of tin content - Titration". Its scope clause reads: This section GB/T 23278 specifies the method for determination of sodium tin tin content.

This section applies to the determination of tin tin sodium content was measured in the range of 35.00% ~ 44.00%. Its clauses include method summary; reagents and apparatus.

Found what you need?

Document preview — GB/T 23278.1-2009

National Standard of the People's Republic of China

ICS
71.040.40
Classification
G 10

Issued by: State Administration for Market Regulation; Standardization Administration of the PRC

Contents

  • 1 Scope
  • 2 Method summary
  • 3 Reagents and apparatus
  • 3.7 starch solution (10g/L)

1 Scope

This section GB/T 23278 specifies the method for determination of sodium tin tin content.

This section applies to the determination of tin tin sodium content was measured in the range of 35.00% ~ 44.00%.

2 Method summary

The sample was dissolved by hydrochloric acid with iron powder, aluminum reduction tin (IV) tin (II), iron powder to eliminate the influence of dissolved oxygen, starch indicator, iodine

Potassium standard solution titration tin (II).

3 Reagents and apparatus

Test water for the three distilled water.

3.1

aluminum (mass fraction >=99.5%).

3.2

reduced iron (by 0.074mm sieve).

3.3

tin (mass fraction >=99.85%).

3.4

hydrochloride (rho1.19g/mL).

3.5

HCl (1 + 1).

3.6

standard potassium iodate titration solution [Ba (1/6KIO3) = 0.05mol/L].

3.6.1 preparation

Weigh 17.9g of potassium iodate dissolved in 500mL of water was added 89.5g of potassium iodide and 10g anhydrous sodium carbonate dissolved in water

Diluted to 10L, shake.

3.6.2 Calibration

Weigh 0.1200g (m1 0) tin (3.3) placed in 300mL conical flask, 1g reduced iron (3.2), 80mL

Hydrochloric acid (3.5), the reduction means connected to the flask. Low tin heated to dissolve, add 20mL water, was added 1.5g of aluminum (3.1). continuous

Shake the flask to dissolve most metals aluminum, heating was continued to boil test solution to produce large bubbles about 1 minute. Under the protection of carbon dioxide gas,

The Erlenmeyer flask into the cold water bath to cool to room temperature. Remove the conical flask and immediately 5mL starch solution (3.7), a standard titration with potassium iodate

Light blue solution was titrated to the end point (Vp 1). At the same time a blank test (V0).

According to equation (1) to calculate the actual concentration of potassium iodate standard titration solution.

Ba m1 = 0

· W1 (Sn) (1)

Where.

Ba --- the actual concentration of potassium iodate standard titration solution, expressed in moles per liter (mol/L);

M1 0 --- metal tin in grams (g);

Quality w1 (Sn) --- tin fraction;

When Vp 1 --- calibration standard potassium iodate titration titration volume consumed tin standard solution, in milliliters (mL);

V0 --- the calibration, the volume of standard potassium iodate titration titration blank test solution consumed solution in milliliters (mL);

When three parallel calibration, the poor value of not more than 1.5 × 10-4mol/L, the mean value, or re-calibration.

3.7 starch solution (10g/L)

Weigh 1g of soluble starch into 300mL beaker, add 20mL water, slurried with stirring plus

Into 20mL of sodium hydroxide solution (25g/L), and dissolved with stirring, was added 60mL of water.

3.8

carbon dioxide gas.

......
This preview omits tables, figures, formulas and parts of the technical clauses. The complete document — 15 pages — is available in the English PDF.

Similar standards

How to Download GB/T 23278.1-2009

  1. 1

    Add to cart

    Click "Download PDF" on this page and choose "Buy this standard". You can add more standards before checkout.

  2. 2

    Checkout

    Enter your email and billing details. Payment is processed securely by Stripe (cards or bank transfer). Prefer bank details? Request a quotation (min. order $300).

  3. 3

    Fast delivery

    After payment you'll receive an email confirmation. The English PDF is sent to the same address, usually within minutes and at the latest within 1 business day.

  4. 4

    Invoice included

    A tax invoice is attached to the confirmation email. Need a custom invoice? Contact us.

Related Standards

English PDF
15 pages
Fast delivery
Invoice included
View Cart

Secure payment via Stripe

Payments accepted

VisaMastercardAmerican ExpressApple PayGoogle PayStripe

GB/T 23278.1-2009

$85.00