GB/T 17810-2009Feed grade DL-methionine (English PDF)
饲料级DL-蛋氨酸
This is a limited preview
Buy now to download the full PDF (15 pages)
Need quotation for your management?
Get a formal quotation for GB/T 17810-2009 in 30 minutes.
Issued by
SAMR; SAC
Level / Type
National · Recommended
Issue date
May 26, 2009
Implementation date
October 1, 2009
Scope
GB/T 17810-2009 is the English-translated version of 饲料级DL-蛋氨酸.
GB/T 17810-2009 is the Chinese standard "Feed grade DL-methionine". Its scope clause reads: This Standard specifies the requirements, test methods, inspection rules, labeling, packaging, storage, and transportation of feed grade DL-methionine products.
This Standard applies to the feed grade DL-methionine that uses methylthiopropanal, cyanide, sulfuric acid, and sodium hydroxide as main raw materials. Chemical name.
2-amino-4-methylthio butyric acid Chemical formula. CH3S-CH2-CH2-CH (NH2) -COOH Relative molecular mass. 149.2 (according to Year-2007 international relative atomic mass).
Its clauses include requirements; test methods; inspection rules; labeling, packaging, transportation, and storage. It was issued by the General Administration of Quality Supervision, Inspection and Quarantine on MAY 26, 2009 and took effect on OCTOBER 1, 2009.
Found what you need?
Document preview — GB/T 17810-2009
National Standard of the People's Republic of China
- ICS
- 65.120
- Classification
- B 46
- Replacing
- GB/T 17810-1999
Issued by: State Administration for Market Regulation; Standardization Administration of the PRC
Contents
- 1 Scope4
- 2 Normative references4
- 3 Requirements5
- 4 Test methods5
- 5 Inspection rules12
- 6 Labeling, packaging, transportation, and storage13
Foreword
This Standard replaces GB/T 17810-1999 "Feed grade DL-methionine".
The main technical differences between this Standard and GB/T 17810-1999 are as follows.
- REVISE GB/T 6678 in normative references to GB/T 14699.1;
- REVISE 3.1 in previous standard to "Appearance and characters - White or light gray powder or flaky crystals. It is slightly-soluble in water. It is extreme-slightly-soluble in ethanol. It is slightly-soluble in diluted acid and sodium hydroxide (potassium) solutions";
- Tolerance in 4.1.5 of previous standard is adjusted from "absolute differences of two parallel determination results shall not be greater than 0.1%" to "absolute differences of two parallel determination results shall not be greater than 0.3%";
- ADD the product identification methods (ion exchange chromatography);
- MODIFY the determination methods of heavy metals;
- MODIFY the arsenic determination methods;
- ADD "factory-exit inspection" and "type inspection" in inspection rules.
1 Scope
This Standard specifies the requirements, test methods, inspection rules, labeling, packaging, storage, and transportation of feed grade DL-methionine products.
This Standard applies to the feed grade DL-methionine that uses methylthiopropanal, cyanide, sulfuric acid, and sodium hydroxide as main raw materials. Chemical name. 2-amino-4-methylthio butyric acid
Chemical formula. CH3S-CH2-CH2-CH (NH2) -COOH Relative molecular mass. 149.2 (according to Year-2007 international relative atomic mass)
2 Normative references
The provisions in following documents become the provisions of this Standard through reference in this Standard. For dated references, the subsequent amendments (excluding corrections) or revisions do not apply to this Standard.
However, parties who reach an agreement based on this Standard are encouraged to study if the latest versions of these documents are applicable.
For undated references, the latest edition of the referenced document applies.
GB/T 601 Chemical reagent - Preparations of standard volumetric solutions
GB/T 1250 Rules for expression and judgment of limiting values
GB/T 6682 Water for analytical laboratory use - Specification and test methods
GB 10648 Feed label
GB/T 14699.1 Animal Feeding Stuffs - Sampling "Pharmacopoeia of People's Republic of China" Volume 2, Edition 2005
3 Requirements
3.1 Appearance and characters
White or light gray powder or flaky crystals. It is slightly-soluble in water. It is extreme-slightly-soluble in ethanol. It is slightly-soluble in diluted acid and sodium hydroxide (potassium) solutions.
4 Test methods
The reagents and the water used in this Standard, except those particularly indicated, refer to the analytical reagents and grade 3 water that is complied with the specifications in GB/T 6682. Instruments and equipment are general laboratory instruments and equipment.
4.1 Appearance and characters
Appearance and character assessment shall meet the requirements of 3.1.
4.2 Identification
4.2.1 Reagents and solutions
4.2.1.1 Saturated anhydrous copper sulfate sulfuric acid solution. TAKE anhydrous copper sulfate. Add to concentrated sulfuric acid. STIR until precipitation occurs.
4.2.1.7 Ninhydrin solution. PREPARE according to the instructions of amino acid automatic analyzer
4.2.1.8 Methionine standard stock solution c(methionine) = 2.50 µmol / mL
WEIGH 93.3 mg of methionine in a 100-mL beaker. ADD about 50 mL of water and several drops of concentrated hydrochloric acid to dissolve. TRANSFER quantitatively to a 250-mL volumetric flask. USE water to dissolve and FIX the volume.
4.2.2 Instruments
Amino acid automatic analyzer. Ninhydrin post-column derivatization ion-exchange chromatography. It requires that the resolution of each amino acid shall be greater than 90%.
4.2.3 Identification steps
4.2.3.1 WEIGH 25 mg of samples. ADD 1 mL of saturated anhydrous copper sulfate sulfuric acid solution (4.2.1.1). The liquid is yellow.
4.3 Determination of DL-methionine content
4.3.1 Principle
ADD excessive iodine solution accurately into neutral medium. ADD 2 iodine atoms to the sulfur atoms of methionine. USE sodium thiosulfate standard titration solution to re-titrated the excessive iodine solution.
4.3.2 Reagents and solutions
4.3.2.1 Potassium phosphate dibasic solution. 500 g / L.
4.3.2.6 Starch solution. 10 g / L.
4.3.3 Instruments
4.3.3.1 Analytical balance. The sensitivity is 0.1 mg.
4.3.3.2 Magnetic stirrer.
4.3.4 Analysis steps
WEIGH 0.23 g ~ 0.25 g of sample (accurate to 0.000 1 g). PUT into a 500-mL iodine flask. ADD 70 mL of deionized water. Then ADD the following reagents respectively. 10 mL of potassium phosphate dibasic solution (4.3.2.1), 10 mL of potassium dihydrogen phosphate solution (4.3.2.2), 10 mL of potassium iodide solution (4.3.2.3). After they are all dissolved, ADD 50.00 mL of iodine solution (4.3.2.4) accurately.
4.3.5 Calculation of the results
Methionine content X1 is calculated according to the formula (1). In the formula.
4.4 Determination of loss on drying
4.4.1 Principle
DRY the samples in a (105 ± 2) °C oven under atmospheric pressure to constant WEIGH.
4.4.2 Analysis steps
WEIGH about 10 g of samples (accurate to 0.000 2g) by a weighing dish which has been constant-weight. PLACE in a 105 °C oven to dry for 3 h. Then TAKE them out. And PUT in a dryer to cool for 30 min. Then WEIGH it. DRY for 1 h in the same way, then WEIGH it, until the difference of mass between 2 weighings is less than 0.002 g.
4.5 Determination of chloride content
4.5.1 Principle
After samples are dissolved, ADD nitric acid and silver nitrate to react with chloride to form silver chloride turbid solution. COMPARE with standard hue.
4.5.2 Reagents and solutions
4.5.3 Analysis steps
4.6 Determination of heavy metals
4.6.1 Principle
After the samples are dissolved, heavy metals react with sodium sulfide to form brown sulfide under the test conditions. COMPARE with comparison solution under the same conditions.
4.6.2 Reagents and solutions
4.6.2.2 Sodium sulfide solution. 100 g / L
4.6.2.1 Sodium hydroxide solution. 43 g / L
5 Inspection rules
5.1 Products shall be inspected by quality inspection department of the manufacturer. The manufacturer shall ensure that all products exiting factory shall meet the requirements of Chapter 3 of this Standard. And accompany with quality certificates in certain format.
5.2 The products produced and packaged by the same batch of raw materials, by the same shift, with the same process condition, same batch number, same specification, and same quality certificates are deemed as a batch.
5.4 Factory-exit inspection. Each batch of products shall be conducted for factory-exit inspection when exiting the factory. The inspection items are sensory index, loss on drying, and DL-methionine content.
5.5 Type inspection. Type inspection shall be conducted once every 6 months.
Type inspection items include all the requirements specified in Chapter 3 of this Standard. When there is 1 of the following situations, it shall conduct type inspection for the product quality.
5.6 Judgment rules. The products of which all inspection results meet the requirements of Chapter 3 of this Standard are judged as qualified. When there is 1 indicator not meeting the requirements of this Standard, it shall be re-sampled for re-inspection. It is judged as unqualified when there is 1 item in re-inspection result not complying with this Standard.
6 Labeling, packaging, transportation, and storage
6.1 The content of labels shall comply with the specification of GB 10648.
6.2 The products are packaged in bags. The packaging bags are divided into 3 layers
6.3 The products shall be prevented from rain, moisture, and sunlight during transportation. It is strictly prohibited that transporting with toxic substances.
6.4 The products shall be stored in a dry, clean indoor warehouse. Avoid the rain and moisture.
6.5 Shelf life of original packaging under specified storage conditions is 36 months. […]
......
This preview omits tables, figures, formulas and parts of the technical clauses. The complete document — 15 pages — is available in the English PDF.
Referenced standards
Similar standards
Editions of GB/T 17810
| Edition | Title | Revision | Status |
|---|---|---|---|
| GB/T 17810-2009 | Feed grade DL-methionine | current edition | Current |
| GB/T 17810-1999 | Feed grade DL-methionine | previous edition | Superseded |
This page sells the current edition, GB/T 17810-2009. Earlier editions are listed for reference only.
How to Download GB/T 17810-2009
- 1
Add to cart
Click "Download PDF" on this page and choose "Buy this standard". You can add more standards before checkout.
- 2
Checkout
Enter your email and billing details. Payment is processed securely by Stripe (cards or bank transfer). Prefer bank details? Request a quotation (min. order $300).
- 3
Instant delivery (0–9 sec)
Delivery is automatic: within seconds of payment you'll receive an email with a secure download link. The link stays valid for 72 hours.
- 4
Invoice included
A tax invoice is attached to the confirmation email. Need a custom invoice? Contact us.
Related Standards
Secure payment via Stripe
Payments accepted
GB/T 17810-2009
$75.00