Valid

GB/T 17116.3-2018Pipe supports and hangers - Part 3: Middle connection attachments and building structure attachments (English PDF)

管道支吊架第3部分:中间连接件和建筑结构连接件

Preview PDF

This is a limited preview

Buy now to download the full PDF (64 pages)

Need quotation for your management?

Get a formal quotation for GB/T 17116.3-2018 in 30 minutes.

Issued by

General Administration of Quality Supervision, Inspection and Quarantine; Standardization Administration of the PRC

Level / Type

National · Recommended

Issue date

March 15, 2018

Implementation date

October 1, 2018

Scope

GB/T 17116.3-2018 is the English-translated version of 管道支吊架第3部分:中间连接件和建筑结构连接件.

GB/T 17116.3-2018 is the Chinese standard "Pipe supports and hangers - Part 3: Middle connection attachments and building structure attachments". Its scope clause reads: This part of GB/T 17116 specifies the typical structure of the pipe hangers with nominal sizes NS10~NS125 and The main connection size.

This section applies to the middle connector and building structural connector of the pipe support and hanger device.

Found what you need?

Document preview — GB/T 17116.3-2018

National Standard of the People's Republic of China

ICS: 23.040.99
Classification: J 15
Replacing: GB/T 17116.3-1997

Issued by: General Administration of Quality Supervision, Inspection and Quarantine; Standardization Administration of the PRC

Preface
1 Scope
2 Normative references
3 Nominal dimensions and thread series for booms and accessories
4 Hanger type size
4.1 Double threaded rod
4.2 Fully threaded boom
4.3 ring eye single threaded rod
4.4 ring eye double threaded rod
5 Hanger Fittings Size
5.1 Spiral Buckle
5.2 Connecting nuts
5.3 U nut
5.4 Ring nut
5.5 double hole connecting plate
5.6 three hole connecting plate
5.7 Nut
5.8 Thin Nut
5.9 Plain Washer
5.10 Ball (cone) face washer
6 Pull Strut and Pin Type Size
6.1 Pull Strut
6.2 Pin seat
7 Types of construction structure connector
7.1 Steel Beam Clamp
7.2 Steel Beam Connection Angle
7.3 Reinforced steel beam
7.4 Pad
7.5 Monocular hanging plate
7.6 U-shaped hanger
7.7 inverted U-shaped hanging plate
7.8 Concrete Rear Anchor

1 Scope

This part of GB/T 17116 specifies the typical structure of the pipe hangers with nominal sizes NS10~NS125 and

The main connection size.

This section applies to the middle connector and building structural connector of the pipe support and hanger device.

2 Normative references

The following documents are indispensable for the application of this document. For dated references, only dated versions apply to this article

Pieces. For undated references, the latest version (including all amendments) applies to this document.

GB/T 95 Flat Washer Class C

GB/T 706-2008 hot-rolled section steel

GB/T 849 spherical washer

GB/T 850 cone washer

GB/T 6170 type 1 hexagon nut

GB/T 6171 Type 1 Hex Nut Fine Teeth

GB/T 6172.1 Hexagon Thin Nut

GB/T 6173 Hexagon Thin Nut Fine Teeth

GB/T 11263 hot-rolled H-section steel and split T-shaped steel

GB/T 15389 screw

GB/T 17116.1-2018 pipe hangers Part 1. Technical specifications

GB/T 17116.2 Pipe Hangers Part 2. Pipe Connection Parts

3 Nominal dimensions and thread series of booms and their accessories

3.1

The nominal dimensions of the boom and its accessories shall be the same as the nominal nominal diameter of the thread. According to the different pitch, the boom and its accessories may be divided into A.

Series and B series, and should comply with the provisions of Table 1.

3.2

The threads of the boom and its accessories can be divided into right-hand threads (indicated by RH) and left-hand threads (indicated by LH). Left thread only for snails

One end of the spinner and the thread of the suspender attached to it.

3.3

The material of threaded rods shall comply with the requirements of Table 7 of GB/T 17116.1-2018.

3.4

The matching of the nominal size of the boom and its fittings to the nominal size of the hanger tube and the load series shall comply with the provisions of GB/T 17116.2. […]

......
This preview omits tables, figures, formulas and parts of the technical clauses. The complete document — 64 pages — is available in the English PDF.

Referenced standards

Normative references

GB/T 849 · GB/T 850

Cited by

Similar standards

GB/T 17116.1-2018|GB/T 17116.2-2018|GB/T 17116.3-1997|GB/T 6170-2015|GB/T 11263-2017|GB/T 706-2016

Editions of GB/T 17116.3

Edition	Title	Revision	Status
GB/T 17116.3-2018	Pipe supports and hangers - Part 3: Middle connection attachments and building structure attachments	first revision	Current
GB/T 17116.3-1997	Pipe supports and hangers - Part 3	first issue	Superseded

This page sells the current edition, GB/T 17116.3-2018. Earlier editions are listed for reference only.

How to Download GB/T 17116.3-2018

1
Add to cart
Click "Download PDF" on this page and choose "Buy this standard". You can add more standards before checkout.
2
Checkout
Enter your email and billing details. Payment is processed securely by Stripe (cards or bank transfer). Prefer bank details? Request a quotation (min. order $300).
3
Instant delivery (0–9 sec)
Delivery is automatic: within seconds of payment you'll receive an email with a secure download link. The link stays valid for 72 hours.
4
Invoice included
A tax invoice is attached to the confirmation email. Need a custom invoice? Contact us.