GB/T 10863-2011Thermal test method for gas pass heat recovery boiler (English PDF)
烟道式余热锅炉热工试验方法
This is a limited preview
Buy now to download the full PDF (36 pages)
Need quotation for your management?
Get a formal quotation for GB/T 10863-2011 in 30 minutes.
Issued by
General Administration of Quality Supervision, Inspection and Quarantine of the People's Republic of China; Standardization Administration of China
Level / Type
National · Recommended
Issue date
December 30, 2011
Implementation date
July 1, 2012
Scope
GB/T 10863-2011 is the English-translated version of 烟道式余热锅炉热工试验方法.
GB/T 10863-2011 is the Chinese standard "Thermal test method for gas pass heat recovery boiler". Its scope clause reads: This standard specifies the flue waste heat boiler thermal test methods, as flue waste heat boiler performance and acceptance tests of the product type in accordance with.
This standard applies to water as the working fluid waste heat boiler flue. This standard does not apply to shell and tube heat recovery boiler. Its clauses include terms and definitions.
Found what you need?
Document preview — GB/T 10863-2011
National Standard of the People's Republic of China
- ICS
- 27.060.30
- Classification
- J98
Issued by: General Administration of Quality Supervision, Inspection and Quarantine of the People's Republic of China; Standardization Administration of China
Contents
- Introduction
- 1 Scope
- 2 Normative references
- 3 Terms and definitions
- 4 Symbols and units
- 5 General
- 6 test preparation
- 7 Test Requirements
- 8 formula
- 9 measurement methods and apparatus
- 10 20 Test Report
- Appendix A (normative) waste heat boiler furnace heat loss
- Annex C (informative) commonly average gas volumetric specific heat at constant pressure
- Annex F (normative) smoke isokinetic sampling method
- Annex G (informative) design data and comprehensive calculation of the test data table
1 Scope
This standard specifies the flue waste heat boiler thermal test methods, as flue waste heat boiler performance and acceptance tests of the product type in accordance with.
This standard applies to water as the working fluid waste heat boiler flue.
This standard does not apply to shell and tube heat recovery boiler.
2 Normative references
The following documents for the application of this document is essential. For dated references, only the dated version suitable for use herein
Member. For cited documents without a date. The latest version (including any amendments) applies to this document.
GB/T 2900.48-2008 Electrotechnical terminology boiler
3 Terms and Definitions
GB/T 2900.48-2008 defined and the following terms and definitions apply to this document.
3.1 Waste heat boiler flue
Use of waste heat medium (a variety of industrial process waste gas, waste or waste) sensible heat contained in or (and) after the burning of combustible substances
Heat (necessary, to add afterburning), and is arranged in the flue of the heating surface heat exchange to generate steam or hot water boiler, a structure similar to
Water tube or shell type boilers.
3.2 Heat input
The total heat input per unit time HRSG heat resources.
3.3 Effective heat output heatoutput
Total calories per unit time in the boiler working fluid absorbed, including heat and water vapor absorption, as well as sewage water and steam consumption for personal use
Consumption of calories.
3.4 Calorific
It refers to combustible materials per unit volume or unit mass of waste heat contained under certain conditions, complete combustion heat released in the buckle
In addition to heat water vapor condenses into water after the latent heat of vaporization obtained.
3.5 Reference temperature
To calculate the energy balance of the boiler heat input and the heat loss to the determined threshold temperature.
3.6 Waste heat utilization
Effective heat output accounted for the percentage of heat input, which represents the formula.
......
This preview omits tables, figures, formulas and parts of the technical clauses. The complete document — 36 pages — is available in the English PDF.
Referenced standards
Normative references
Cited by
- GB/T 1921-2025Specification for industrial boilers
- GB/T 28056-2025Specification for heat recovery boilers
- GB/T 44553-2024Technical specification for the energy saving of hot-dip galvanizing production lines
- GB/T 16507.1-2022Water-tube boilers - Part 1: General requirements
- GB/T 16508.1-2022Shell boilers - Part 1: General requirements
- GB/T 10868-2018Steam converting valves for power station
Similar standards
Editions of GB/T 10863
| Edition | Title | Revision | Status |
|---|---|---|---|
| GB/T 10863-2011 | Thermal test method for gas pass heat recovery boiler | current edition | Current |
| GB 10863-1989 | Thermal test method for gas pass waste heat boiler | merged into this edition | Superseded |
This page sells the current edition, GB/T 10863-2011. Earlier editions are listed for reference only.
How to Download GB/T 10863-2011
- 1
Add to cart
Click "Download PDF" on this page and choose "Buy this standard". You can add more standards before checkout.
- 2
Checkout
Enter your email and billing details. Payment is processed securely by Stripe (cards or bank transfer). Prefer bank details? Request a quotation (min. order $300).
- 3
Instant delivery (0–9 sec)
Delivery is automatic: within seconds of payment you'll receive an email with a secure download link. The link stays valid for 72 hours.
- 4
Invoice included
A tax invoice is attached to the confirmation email. Need a custom invoice? Contact us.
Related Standards
GB/T 2900.48-2008 — Electrotechnical terminology of boilers
GB/T 10003-2026 — Biaxially oriented polypropylene (BOPP) film
GB/T 10004-2026 — Plastic/Plastic laminated films and pouches for packaging
Secure payment via Stripe
Payments accepted
GB/T 10863-2011
$560.00