GB 24727-2009Safety specifications for use garden patrol minibus (English PDF)

4.1 Pairs of the user's requirements

4.1.1 Use national tourist vehicles in the designated area.

4.1.2 should have a wagon operator qualification; people should drive tourist vehicles driving qualifications.

4.1.3 shall establish and comply with sightseeing bus safety management system use, the contents should include at least.

a) should be prohibited from carrying flammable, explosive and other dangerous goods personnel take a sightseeing tour into the car or vehicle use of premises;

b) mobility of the elderly, children, pregnant women and persons with disabilities to take sightseeing car, should be the guardian care, to ensure their safe ride;

c) tourist vehicles should be designed in a predetermined load operation, each of the seat occupant has to ensure uniform distribution of the vehicle load;

d) unforeseen circumstances, there should be security measures to ease the operation occurred when sightseeing car;

e) tourist car driver safety rules;

f) sightseeing car vehicle maintenance, maintenance system.

4.1.4 modification

4.1.4.1 design unit without consent, should not affect the safety performance of tourist vehicles were modified.

4.1.4.2 tourist vehicles have special requirements for modification shall be submitted to the manufacturer at the time of purchase.

4.1.4.3 sightseeing car modified by the manufacturer or qualified units. Safety performance after modifications should be consistent with GB/T 21268 Provisions.

4.1.4.4 modified after the sightseeing car, its signs and logos should be consistent with the use of performance and safety, and should be fixed at a predetermined position.

4.1.5 Use

4.1.5.1 wagon operator shall meet the design requirements and should not overload operation.

4.1.5.2 wagon environment should meet the design requirements.

4.1.5.3 Use sightseeing car, make sure it is in a safe condition. Found safety problems, should be suspended. After eliminating the risks can be put into use.

4.1.5.4 tourist vehicles should be equipped with reliable performance, in the fire-fighting equipment within the validity period.

4.1.5.5 having a closed body structure tourist vehicles with an emergency channel, and ensure smooth flow.

4.1.6 Diesel fuel and container wagon

4.1.6.1 raise fuel combustion sightseeing car, should meet the grade specified by the manufacturer.

4.1.6.2 The user should have to the provisions of the qualification filling station fueling. LPG containers

4.1.6.3 tourist vehicles equipped and should not be replaced or modified without permission.

4.1.7 Battery charging and replacement

4.1.7.1 Battery charging stations should be set up within the designated area, in the region should set up warning signs prohibiting fireworks.

4.1.7.2 Battery charging stations should be equipped with equipment and can wash and electrolyte overflow device.

4.1.7.3 Battery charging or replacement should be performed by qualified personnel.

4.1.7.4 Battery installation shall comply with GB/T 21268-2007 provisions in 5.10. Should ensure accurate positioning, fixation line Road connections are correct.

4.1.7.5 Battery lifting should adopt the insulated boom.

4.1.7.6 with chain hoist lifting the battery, should be equipped with chain box; lifting hoist hand pull the battery, it should be covered with an insulating material in the battery Material, in order to avoid a chain connected to a terminal battery terminal short circuit.

4.1.7.7 Battery voltage should comply with the design requirements, users should not switch to a different voltage batteries.

4.1.7.8 of waste batteries (liquid) process, should be the relevant national regulations.

4.1.8 Wagon transport, handling and hoisting

4.1.8.1 loading wagon vehicle, should ensure with sufficient carrying capacity. Transportation sightseeing car, sightseeing car should prevent the movement must To measure.

4.1.8.2 user should specify the location of lifting and handling sightseeing car factory.

4.1.8.3 for handling and lifting with special transportation requirements sightseeing car, you should follow the procedure of the manufacturer's instructions.

4.2 pairs of driver requirements

4.2.1 should drive tourist vehicles operating within the specified area.

4.2.2 shall comply with safety rules and safety regulations within the operational area of wagon. Sightseeing parked car before 4.2.3, does not allow the passengers to get off.

4.2.4 sightseeing before starting the car, check whether passengers should wear seatbelts.

4.2.5 sightseeing car moving process, shall inform passengers not to leave the seat should not lean out of the body outside of the contour.

4.2.6 Run

4.2.6.1 Drivers' tourist car in the designated area, the building should pay particular attention to pedestrians, vehicles and around, to ensure traffic safety.

4.2.6.2 sightseeing before starting the car, the driver deal with the technical condition inspection, confirmed normal before operation.

4.2.6.3 Drivers' sightseeing car, should avoid sudden start, stop and high-speed cornering. Start the vehicle, the steering wheel should not be at the limit Position (except in exceptional circumstances).

4.2.6.4 tourist vehicles traveling at a crossroads and the view is obstructed location or other dangerous situations, should reduce the speed, warning whistle through; should be maintained Hold normal driving, not to exceed with the other vehicle.

4.2.6.5 tourist cars run, the driver should not lean out of the outer contour of the vehicle body.

4.2.6.6 tourist vehicles traveling in the designated area, shall comply with the carrying capacity of the road and other signs indicating requirements.

4.2.6.7 tourist vehicles running on a slope, the following rules apply.

a) slowly through the upper and lower ramp;

b) should not be a U-turn on the slope and should not run across the ramp;

c) should not be neutral slide downhill;

d) close ramps, elevated platforms or platform edge, the distance between the body and the edge of the platform or the platform is at least a sightseeing car tires Width.

4.2.6.8 sightseeing car before driving through the bridge, the holes, the driver should confirm that there is sufficient through space.

4.2.6.9 driver leaves the sightseeing car, sightseeing car should be in a neutral position; turn off the power source; tighten parking brake; remove the key.

4.2.7 Sightseeing car fueling internal combustion

4.2.7.1 before refueling, the driver should turn off the engine, brake tourist vehicles.

4.2.7.2 When refueling, the driver and passengers shall comply with the requirements of its own safety management system raise workplace.

4.2.7.3 In the removal of fueling equipment, cover the filler cap and remove fuel spills before, should not start the engine.

4.2.7.4 The driver should go through the necessary training before engaging in replacement of LPG container work.

4.2.8 Battery charging and replacement

4.2.8.1 The driver should go through the necessary training before engaging in rechargeable battery or replacement.

4.2.8.2 replace the battery or charge the battery before, you should brake the vehicle, and positioned correctly.

4.2.8.3 Battery charging and changing approaches reference 4.1.8. 5 maintenance, service and repair

5.1 pairs of the user's requirements

5.1.1 should be regularly checked and maintained sightseeing bus signs, the integrity of the logo.

5.1.2 should be regular inspections and ensure that all sightseeing car safety performance indicators in line with the provisions of GB/T 21268 of.

5.1.3 should develop and comply with sightseeing car maintenance, maintenance procedures, the procedures should include at least all the items 5.1.4.

5.1.4 wagon maintenance, repairs should be made by qualified units.

5.1.5 maintenance, service programs Project

5.1.5.1 of the vehicle brakes, steering mechanism, controls, instruments, lights, horn, passenger protection devices should be regularly maintained And maintenance, use it in a safe state.

5.1.5.2 the battery, motor, emergency off devices, signal and lighting fixtures, controllers and contactors, limit switches, wires and patch And other pieces of equipment should be regular maintenance and repair, with particular attention to the electrical insulation status, holding a variety of devices in a safe condition.

5.1.5.3 The exhaust system of an internal combustion vehicle, the fuel system should be checked regularly for damage and leakage.

5.1.5.4 should be checked regularly pneumatic tire tread, side and rim. The pneumatic tire shall maintain a predetermined pressure; according to wear, for Damaged tread, side and rims to be more (adjusted) exchange.

5.1.5.5 disassembly open-pneumatic tire on the rim, the gas should be pre-pneumatic tire within the drain.