QC/T 1094-2018General specification of lithium ion batteries for motorcycle starting (English PDF)
摩托车起动用锂离子电池通用技术条件
This is a limited preview
Buy now to download the full PDF (29 pages)
Need quotation for your management?
Get a formal quotation for QC/T 1094-2018 in 30 minutes.
Issued by
MIIT
Level / Type
Industry · Recommended
Issue date
July 4, 2018
Implementation date
January 1, 2019
Scope
QC/T 1094-2018 is the English-translated version of 摩托车起动用锂离子电池通用技术条件.
QC/T 1094-2018 covers lithium-ion batteries used for starting motorcycles and specifies their type and structure, requirements, test methods, inspection rules and the marking, packaging, transportation and storage provisions.
Product naming, model designations and overall dimensions are tabulated by model. Acceptance requirements cover appearance, secured lead-out cables, polarity matching the marked symbols and dimensions, and a discharge capacity of at least 90 percent of the tabulated value.
In room-temperature high-rate discharge the voltage shall not fall below 10.0 V at 5 s and 7.2 V at 90 s; in low-temperature high-rate discharge it shall not fall below 7.2 V at 5 s or at 90 s.
Charge acceptance requires the ratio of charging current to Ia at the tenth minute to be greater than 6.0, cycle life shall be at least 1000 cycles, high-temperature charge storage shall leave not less than 9.3 V after 30 s of discharge, room-temperature charge storage not less than 90 percent of nominal capacity, and storage not less than 85 percent.
Over-discharge recovery requires more than 80 percent of nominal capacity without fire, explosion or leakage. Safety clauses address overcharge, short circuit, drop, heating, extrusion and nail penetration, and further clauses cover vibration, withstand current, sealing when lifted and terminal torque.
Tests run at 25 degrees C plus or minus 5 degrees C, with charging at 0.5C2A up to 14.4 V held for 4 h and the capacity discharge at I2 down to a 9.6 V end voltage.
Found what you need?
Document preview — QC/T 1094-2018
National Standard of the People's Republic of China
- Classification
- T 85
Issued by: Ministry of Industry and Information Technology of the People's Republic of China
Contents
- 1 Scope
- 2 Normative references
- 3 Terms and Definitions
- 4 Model and structure
- 5 Requirements
- 6 Test method
1 Scope
1.1 This standard specifies the type and structure, requirements, test methods, inspection rules and the marking, packaging, transportation and storage of lithium-ion batteries used for starting motorcycles.
1.2 This standard applies to lithium-ion batteries (hereinafter referred to as "batteries") used for motorcycle starting.
2 Normative references
The following documents are indispensable for the application of this document. For dated references, only the dated version applies to this document. For undated reference documents, the latest version (including all amendments) applies to this document.
3 Terms and Definitions
The following terms and definitions contained in GB/T 2900.41, GB/T 23638, GB/T 31485 and GB/T 18287 apply to this standard.
4 Model and structure
4.1 Product Naming Method and Model
4.1.1 See Figure 1 for the product naming method and Table 1 for the product model.
4.2 Structure
4.2.1 The marking method of product outline and dimension is shown in Figure 3.
4.2.2 The external dimensions in Table 1 refer to the external dimensions of the groove and cover, excluding the battery connectors and terminal protruding parts.
4.2.3 Batteries with special specifications not listed in Table 1 shall be determined through negotiation between the manufacturer and the user.
5 Requirements
5.1 Appearance, polarity, dimensions
5.1.1 Appearance
5.1.1.1 The appearance of the battery should be clear, and there should be no cracks, cracks, dents, trachoma, deformation and other forms of mechanical damage. Lead wires should not be corroded.
5.1.1.2 All lead-out cables of the battery should have fixing devices to prevent the cables from rotating and pulling out, and there should be no cables pulling out, disconnection, mechanical deformation and loose joints, and cables should not have exposed wires.
5.1.2 Polarity
The polarity of the battery should be consistent with the polarity symbol on the mark.
5.1.3 Dimensions
The battery dimensions are listed in Table 1.
5.2 Capacity
After the battery is tested according to the provisions of 6.3.3, the discharge capacity should reach 90% or more of the capacity shown in Table 1.
5.3 High rate discharge characteristics at room temperature
After the battery is tested according to the provisions of 6.3.4, the voltage of the battery should not be lower than 10.0V for 5s, and not lower than 7.2V for 90s.
5.4 Low temperature high rate discharge characteristics
After the battery is tested according to the provisions of 6.3.5, the voltage of the battery should not be lower than 7.2V after 5s discharge, and the voltage should not be lower than 7.2V after 90s discharge.
5.5 Charge acceptance
When the battery is tested according to the provisions of 6.3.6, the ratio of the charging current to Ia at the 10th minute should be greater than 6.0.
5.6 Vibration resistance
After the battery is subjected to vibration according to the provisions of 6.3.7, it shall meet the following requirements:
a) The shell is not deformed and does not exceed the specified range of external dimensions.
b) There is no abnormal drop in voltage;
c) The battery has no cracks in the battery slot, no leakage, no fire, no explosion.
5.7 Withstand Current Characteristics
After the battery is tested according to the provisions of 6.3.8, the appearance of the battery has no damage or deformation.
5.8 Cycle Life
After the battery is tested according to the provisions of 6.3.9, the cycle life of the battery should not be less than 1000 times.
5.9 Charge retention characteristics
5.9.1 High temperature charge storage characteristics
After the battery is tested according to the provisions of 6.3.10.1, the voltage should not be lower than 9.3V after 30s of discharge.
5.9.2 Charge storage characteristics at room temperature
After the battery is tested according to the provisions of 6.3.10.2, the battery capacity should not be lower than 90% of the nominal capacity.
5.10 Storage Characteristics
After the battery is tested according to the provisions of 6.3.11, the battery capacity should not be lower than 85% of the nominal capacity.
5.11 Over-discharge recovery characteristics
After the battery is tested according to the provisions of 6.3.12, the battery should not catch fire, explode or leak, and the discharge capacity of the battery should be greater than 80% of the nominal capacity, and the voltage should not be lower than 7.2V after 30 seconds of discharge.
5.12 Security
5.12.1 Overcharge
After the battery is tested according to the provisions of 6.3.13.1, the battery should not catch fire or explode.
5.12.2 Short circuit
After the battery is tested according to the provisions of 6.3.13.2, the battery should not catch fire or explode.
5.12.3 Drop test
After the battery is tested according to the provisions of 6.3.13.3, the battery should not catch fire, explode or leak.
5.12.4 Heating test
After the battery is tested according to the provisions of 6.3.13.4, the battery should not catch fire or explode, and the discharge capacity of the battery should not be lower than 80% of the nominal capacity.
5.12.5 Extrusion test
After the battery is tested according to the provisions of 6.3.13.5, the battery should not catch fire or explode.
5.12.6 Acupuncture test
After the battery is tested according to the provisions of 6.3.13.6, the battery should not catch fire or explode.
5.13 Tightness when lifting
After the battery is tested according to the provisions of 6.3.14, the terminals and cover should not be damaged, and the fully sealed battery should not leak.
5.14 Terminal torque
After the battery is tested according to the provisions of 6.3.15, the connection point between the terminal and the battery cover should not be damaged or deformed.
6 Test method
6.1 Test conditions
Unless otherwise specified, the test is carried out in an environment with a temperature of 25°C±5°C, a relative humidity not greater than 90%, and an atmospheric pressure of 86-106kPa.
6.2 Measuring instruments and equipment requirements
6.2.1 Voltmeter: the accuracy is not lower than 0.5 grade, and its internal resistance is at least 1 kohm/V.
6.2.2 Ammeter: the accuracy is not lower than 0.5 grade.
6.2.3 Thermometer: it has an appropriate range, and its division value is not more than 0.5°C, and the allowable error is ±1°C.
6.2.4 Timer: divided by hour, minute and second, with an accuracy of ±1%.
6.2.5 Measuring tools for measuring dimensions: the graduation value is not greater than 1mm, and the accuracy is ±0.02mm.
6.2.6 Measuring pressure gauge: the accuracy level shall not be lower than 1.0.
6.3 Test methods for batteries
6.3.1 Appearance, polarity, dimensions
6.3.1.1 Appearance
Check the appearance of the battery by visual inspection, it should meet the requirements of 5.1.1.
6.3.1.2 Polarity
Measure the polarity of the battery with the 20V voltage block of the multimeter, which should meet the requirements of 5.1.2.
6.3.1.3 Dimensions
Measuring the external dimensions of the battery with a general measuring tool should meet the requirements of 5.1.3.
6.3.2 Charging
Under the environmental conditions of 25°C±5°C, the battery is charged with a current of 0.5C2A, and when the terminal voltage of the battery during charging reaches 14.4V, it is continuously charged at the same voltage for 4 hours.
6.3.3 Capacity
Charge the battery according to the regulations in 6.3.2 and put it on hold for 1 hour, then discharge it with a current (I2) at a rate of 2 hours in an environment of 25°C±5°C until the end voltage is 9.6V, and calculate the battery by the product of the current and the discharge time discharge capacity. The battery discharge capacity should meet the requirements of 5.2. However, when the capacity does not reach 90% of the capacity shown in Table 1, it can be measured twice more continuously, for a total of three times, and one of them can meet the requirements.
6.3.4 High rate discharge characteristics at room temperature
After the battery is charged according to the provisions of 6.3.2, in the environment of 25°C±5°C, discharge for 90s according to the discharge current of the high-rate discharge characteristics in Table 1, set the end-of-discharge voltage to 7.2V, and record the discharge current for 5s and 90s. battery voltage. The test can be repeated 3 times, and within 3 tests, the high-rate discharge characteristics of the battery at room temperature should meet the requirements of 5.3. Before carrying out this test, the battery must have completed the capacity test in 6.3.3.
......
This preview omits tables, figures, formulas and parts of the technical clauses. The complete document — 29 pages — is available in the English PDF.
Similar standards
How to Download QC/T 1094-2018
- 1
Add to cart
Click "Download PDF" on this page and choose "Buy this standard". You can add more standards before checkout.
- 2
Checkout
Enter your email and billing details. Payment is processed securely by Stripe (cards or bank transfer). Prefer bank details? Request a quotation (min. order $300).
- 3
Fast delivery
After payment you'll receive an email confirmation. The English PDF is sent to the same address, usually within minutes and at the latest within 1 business day.
- 4
Invoice included
A tax invoice is attached to the confirmation email. Need a custom invoice? Contact us.
Related Standards
QC/T 1005-2026 — Performance requirements and bench test methods for hydraulic solenoid valve assembly of electronic stability control system and antilock brake system of automoive
QC/T 1022-2026 — Technical specifications and test methods of reduction gearbox for battery electric vehicles
QC/T 1041-2026 — Control system of fuel evaporative pollutants from Motorcycles with petrol engine
QC/T 1094-2018
$235.00