Valid

JB/T 8896-1999Industrial robots - Acceptance rules (English PDF)

工业机器人 验收规则

Preview PDF

This is a limited preview

Buy now to download the full PDF (15 pages)

Need quotation for your management?

Get a formal quotation for JB/T 8896-1999 in 30 minutes.

Issued by

MIIT

Level / Type

Industry · Recommended

Issue date

June 28, 1999

Implementation date

January 1, 2000

Scope

JB/T 8896-1999 is the English-translated version of 工业机器人 验收规则.

JB/T 8896-1999 is the Chinese standard "Industrial robot. Acceptance rules". Its scope clause reads: This Standard specifies the inspection rules and test methods of industrial robot.

This Standard is applicable to the industrial robots for various uses. Its clauses include inspection rules; inspection items; test methods. It was issued by the State Bureau of Machinery Industry on JUNE 28, 1999 and took effect on JANUARY 01, 2000.

Found what you need?

Document preview — JB/T 8896-1999

National Standard of the People's Republic of China

Issued by: Ministry of Industry and Information Technology of the People's Republic of China

Contents

  • Foreword3
  • 1 Scope4
  • 2 Normative References4
  • 3 Inspection Rules5
  • 4 Inspection Items7
  • 5 Test Methods7

1 Scope

This Standard specifies the inspection rules and test methods of industrial robot.

This Standard is applicable to the industrial robots for various uses.

2 Normative References

The following standards contain provisions which, through reference in this Standard, constitute provisions of this Standard. At the time of publication, the editions indicated are valid. All standards are subject to revision. The parties who are using this Standard shall explore the possibility of using the latest version of the following standards.

GB/T 2423.1-1989 Basic Environmental Testing Procedures for Electric and Electronic Products - Test A: Test Methods for Cold

GB/T 2423.2-1989 Basic Environmental Testing Procedures for Electric and Electronic Products - Test B: Test Methods for Dry Heat

GB/T 2423.3-1993 Basic Environmental Testing Procedures for Electric and Electronic Products - Test Ca: Test Methods for Damp Heat in Steady State

GB/T 2423.10-1995 Basic Environmental Testing Procedures for Electric and Electronic Products - Test Fc: Test Methods for Vibration (Sinusoidal)

GB/T 3768-1996 Acoustics - Determination of Sound Power Levels of Noise Sources Using Sound Pressure--Survey Method Using an Enveloping Measurement Surface over a Reflecting Plane

GB/T 3785-1983 Electric, Sonic Properties and Measuring Methods for Sound Level Meters

GB/T 5226.1-1996 Electrical Equipment of Industrial Machines. Part 1: General Requirements

GB 11291-1997 Industrial Robots - Safety Specification

GB/T 12642-1990 Industrial Robots - Performance Criteria

GB/T 12643-1997 Industrial Robots - Vocabulary is judged to be unqualified.

3 Inspection Rules

3.3 Type inspection

3.3.1 The industrial robot that conducts the type inspection must be product that has passed the exit-factory inspection; the number of testing shall be specified by the product standard.

3.3.2 The type inspection shall be implemented by the quality inspection department of the manufacturer, or by the superior responsible institution.

3.3.3 The type inspection items are as specified in Table 1.

3.3.4 When any an item does not meet the requirements or occurs failure in the inspection, find out the cause; rework it; and re-inspect from such item. If certain item occurs failure or does not meet the requirements again, after finding out the cause, analysis report shall be proposed; after reworking, the type inspection for each item shall be reconducted. If such item still does not meet the requirements in the re-inspection, comprehensively analyze; take measures against such batch of products wholly; and re-deliver them for type inspection. The sample through the type inspection shall be marked.

3.3.5 After inspection, propose the type inspection report.

4 Inspection Items

4.2 Reliability, other special items and parameter indexes shall be specified by the product standard.

4.3 User's acceptance item shall be specified by the product standard.

4.1 The general items can refer to Table 1

5 Test Methods

5.1 Environmental conditions of test

Unless otherwise specified in this Standard, all tests shall be carried out under the following conditions: Temperature: 5~40°C; Relative humidity: 45%~75%;

Test procedure: draw the working space map according to the working space drawing method (see GB/T 12644).

Take the frame coordinate system as a basis, test the coordinate value of each special point (limit location point and inflection point) on the working space.

5.4.3 Maximum single-axis speed and rated speed

See GB/T 12645.

5.4.4 Pose characteristics

See GB/T 12642 and GB/T 12645.

5.4.5 Path characteristics

See GB/T 12642 and GB/T 12645.

5.4.6 Minimum positioning pose time

See GB/T 12642 and GB/T 12645.

5.4.7 Static flexibility

See GB/T 12642 and GB/T 12645.

5.5 Electrical safety test

5.5.1 Continuity of protective grounding circuit

Test as per the requirements of GB/T 5226.1.

5.5.2 Insulation resistance test

Test as per the requirements of GB/T 5226.1, its results shall meet the requirements of product standard.

5.5.3 Withstand voltage test

See GB/T 5226.1.

5.6 Continuous operation test

Conduct teaching programming on the industrial robot; it shall work normally and continuously for 120h under the rated load state and actual work. If it occurs failure in the operating period, after removing the faults, re-start the industrial robot; however, the operating time shall be re-calculated.

As the continuous operating test is taken, test that the following items shall meet the […]

5.10.2.2 Lower limit storage temperature test

It shall be carried out as per "Test Ad" in GB/T 2423.1. Place the tested sample into the low-temperature box, make the temperature within the box reduce to -40°C; store for 4h. After 4h, make the temperature within the box gradually rise to the normal atmospheric condition, restore for 4h under such condition; the temperature-rise time shall not be included into the restoring time.

Check the appearance, which shall meet the requirements of the product standard; then power on and operate, it shall work normally.

In order to prevent the icing and condensing of the tested sample in the test, the tested sample is allowed to be sealed by the plastic film for test; if necessary, the water absorber is allowed to be injected into the packet.

5.10.3 Upper limit temperature test
5.10.3.1 Upper limit working temperature test

It shall be carried out as per "Test Bb" in GB/T 2423.2. Place the tested sample into the high-temperature box, make the temperature within the box increase to 40°C; maintain at least 30min; then power on and operate for 4h, it shall work normally.

5.10.3.2 Upper limit storage temperature test

It shall be carried out as per "Test Bb" in GB/T 2423.2. Place the tested sample into the high-temperature box, make the temperature within the box increase to 55°C; store for 4h. After 4h, make the temperature within the box gradually decrease to the normal atmospheric condition, restore for 4h under such condition; the temperature-drop time shall not be included into the restoring time. Check the appearance, which shall meet the requirements of the product standard; then power on and operate, it shall work normally.

5.10.4 Constant damp and heat test
5.10.4.1 Constant damp and heat test under working condition

It shall be carried out as per "Test Ca" in GB/T 2423.3. Place the tested sample into the damp-heat box; adjust the temperature at 40°C; then maintain at least 30min; inject moisture; make the humidity reach 80% (40°C) within 1h; the above two items shall not be included in the test time.

Test time is 48h; power on and operate during this period, it shall work normally.

5.10.4.2 Constant damp and heat test under storage condition

It shall be carried out as per "Test Ca" in GB/T 2423.3. Place the tested sample into […]

......
This preview omits tables, figures, formulas and parts of the technical clauses. The complete document — 15 pages — is available in the English PDF.

Referenced standards

Normative references

Similar standards

How to Download JB/T 8896-1999

  1. 1

    Add to cart

    Click "Download PDF" on this page and choose "Buy this standard". You can add more standards before checkout.

  2. 2

    Checkout

    Enter your email and billing details. Payment is processed securely by Stripe (cards or bank transfer). Prefer bank details? Request a quotation (min. order $300).

  3. 3

    Fast delivery

    After payment you'll receive an email confirmation. The English PDF is sent to the same address, usually within minutes and at the latest within 1 business day.

  4. 4

    Invoice included

    A tax invoice is attached to the confirmation email. Need a custom invoice? Contact us.

Related Standards

English PDF
15 pages
Fast delivery
Invoice included
View Cart

Secure payment via Stripe

Payments accepted

VisaMastercardAmerican ExpressApple PayGoogle PayStripe

JB/T 8896-1999

$85.00