Valid

JB/T 6644-2007Rolling bearings - Combined needle roller and double-direction thrust cylindrical roller bearings (English PDF)

滚动轴承 滚针和双向推力圆柱滚子 组合轴承

Preview PDF

This is a limited preview

Buy now to download the full PDF (15 pages)

Need quotation for your management?

Get a formal quotation for JB/T 6644-2007 in 30 minutes.

Issued by

MIIT

Level / Type

Industry · Recommended

Issue date

January 1, 2007

Implementation date

September 1, 2007

Scope

JB/T 6644-2007 is the English-translated version of 滚动轴承 滚针和双向推力圆柱滚子 组合轴承.

JB/T 6644-2007 is the Chinese standard "Rolling bearings - Combined needle roller and double-direction thrust cylindrical roller bearings".

Its scope clause reads: This standard specifies the structural type, dimensions and specifications of combined needle roller bearings with double direction thrust roller bearings (hereinafter referred to as “combined bearings”).

This standard is applicable to the combined bearings production and inspection by bearing manufacturer and finished combined bearings selection and acceptance by customers. Its clauses include symbols; structural types (see figure 1 ~ figure 4).

Found what you need?

Document preview — JB/T 6644-2007

National Standard of the People's Republic of China

ICS
21.100.20
Replacing
JB/T 6644-1993

Issued by: Ministry of Industry and Information Technology of the People's Republic of China

Contents

  • Foreword
  • 1 Scope
  • 2 Normative References
  • 3 Symbols
  • 4 Structural Types
  • 5 Dimensions
  • 6 Technical Requirements
  • 6.1 Materials and Heat Treatment
  • 6.2 Tolerance
  • 6.3 Surface Roughness
  • 6.4 Internal Clearance
  • 6.5 Residual Magnetism
  • 6.6 Appearance Quality
  • 6.7 Interchangeability
  • 6.8 Miscellaneous
  • 7 Measurement Methods
  • 8 Inspection Rules
  • 9 Marking
  • 10 Rust Prevention and Packaging
  • Appendix A (Normative) Measurement Methods for deltaTs, Sia, Kia, Kea and Sd

1 Scope

This standard specifies the structural type, dimensions and specifications of combined needle roller bearings with double direction thrust roller bearings (hereinafter referred to as “combined bearings”).

This standard is applicable to the combined bearings production and inspection by bearing manufacturer and finished combined bearings selection and acceptance by customers.

2 Normative References

The following standards contain provisions which, through reference in this text, constitute provisions of this standard. For dated reference, subsequent amendments to (excluding corrections to), or revisions of, any of these publications do not apply. However, the parties to agreements based on this standard are encouraged to investigate the possibility of applying the most recent editions of the standards. For undated references, the latest edition of the normative document referred to applies.

GB/T 307.2-2005 Rolling Bearings-Measuring and Gauging Principles and Methods (ISO 1132-2: 2001, Rolling bearings-Tolerances-Part 2: Measuring and gauging principles and methods, MOD)

GB/T 307.3-2005 Rolling Bearings-General Technical Regulations

GB/T 4199-2003 Rolling Bearings-Tolerances-Definitions (ISO 1132-1: 2000, Rolling bearings-Tolerances-Part 1: Terms and definitions, MOD)

GB/T 4604-2006 Rolling Bearings-Radial Internal Clearance (ISO 5753: 1991, MOD)

GB/T 8597-2003 Rolling Bearings-Rust Proof Packaging

GB/T 18254-2002 High-carbon Chromium Bearing Steel

JB/T 1255-2001 Specification for Heat-treatment of Rolling Bearing Parts Made from High Carbon Chromium Steel

JB/T 3573-2004 Rolling Bearings-Methods for the Measurement of Radial Internal Clearance

JB/T 3574-1997 Rolling Bearings-Marking for Products

JB/T 6641-2007 Rolling Bearings-Residual Magnetism and Its Assessment Method

JB/T 7051-2006 Rolling Bearing Parts-Methods for the Measurement and Assessment of Surface Roughness

3 Symbols

For the purpose of this standard, the following terms and definitions as well as those specified in GB/T 4199 apply.

C: the nominal width of outer ring;

C1: the nominal width of outer ring step;

C2: the distance from the outer ring face to the center line of radial oil hole;

D: the nominal outside diameter of outer ring of combined bearing;

D1: the nominal outside diameter of shaft washer of combined bearing;

D2: the nominal outside diameter of stepped shaft of stepped shaft washer of combined bearing;

D3: the nominal outside diameter of stepped shaft washer of combined bearing;

d: the nominal bore diameter of inner ring;

d1: the nominal bore diameter of shaft washer;

di: the oil hole diameter;

dm: the diameter of bolt hole;

J: the center circle diameter of oil hole and bolt hole;

r: the nominal chamfer dimension of shaft washer;

r1: the nominal chamfer dimension of outer ring;

rsmin: the smallest single chamfer dimension of r;

r1smin: the smallest single chamfer dimension of r1;

Sia: the axial runout of combined bearing;

T: the nominal height of combined bearing;

T1: the distance from outer ring face to the bottom surface of shaft washer;

T2: the nominal height of shaft washer;

T3: the nominal height of stepped shaft washer;

T4: the nominal height of stepped shaft of stepped shaft washer;

VCs: the variation of outer ring width;

deltaD1mp: the deviation of mean outside diameter in a single plane of shaft washer;

deltaD2mp: the deviation of mean outside diameter in a single plane of stepped shaft of stepped shaft washer;

deltaD3mp: the deviation of mean outside diameter in a single plane of stepped shaft washer;

deltad1mp: the deviation of mean bore diameter in a single plane of shaft washer.

4 Structural Types (See Figure 1 ~ Figure 4)

......
This preview omits tables, figures, formulas and parts of the technical clauses. The complete document — 15 pages — is available in the English PDF.

Referenced standards

Similar standards

Editions of JB/T 6644

EditionTitleRevisionStatus
JB/T 6644-2007Rolling bearings - Combined needle roller and double-direction thrust cylindrical roller bearingscurrent editionCurrent
JB/T 6644-1993Rolling bearings - Combined needle roller and double-direction thrust cylindrical roller bearingsprevious editionSuperseded

This page sells the current edition, JB/T 6644-2007. Earlier editions are listed for reference only.

How to Download JB/T 6644-2007

  1. 1

    Add to cart

    Click "Download PDF" on this page and choose "Buy this standard". You can add more standards before checkout.

  2. 2

    Checkout

    Enter your email and billing details. Payment is processed securely by Stripe (cards or bank transfer). Prefer bank details? Request a quotation (min. order $300).

  3. 3

    Fast delivery

    After payment you'll receive an email confirmation. The English PDF is sent to the same address, usually within minutes and at the latest within 1 business day.

  4. 4

    Invoice included

    A tax invoice is attached to the confirmation email. Need a custom invoice? Contact us.

Related Standards

English PDF
15 pages
Fast delivery
Invoice included
View Cart

Secure payment via Stripe

Payments accepted

VisaMastercardAmerican ExpressApple PayGoogle PayStripe

JB/T 6644-2007

$105.00