JB/T 5313-2001Rolling bearings - Measuring methods for vibration (velocity) (English PDF)
滚动轴承 振动(速度)测量方法
This is a limited preview
Buy now to download the full PDF (15 pages)
Need quotation for your management?
Get a formal quotation for JB/T 5313-2001 in 30 minutes.
Issued by
MIIT
Level / Type
Industry · Recommended
Issue date
May 23, 2001
Implementation date
October 1, 2001
Scope
JB/T 5313-2001 is the English-translated version of 滚动轴承 振动(速度)测量方法.
JB/T 5313-2001 is the Chinese standard "Rolling bearings - Measuring methods for vibration (velocity)". Its scope clause reads: This standard specifies measuring methods for vibration (velocity) of DN 3~120mm deep groove ball bearings, angular contact ball bearing, tapered roller bearing and cylindrical roller bearing (Types N, NU, NJ and NF).
This standard is applicable to the inspection of the vibration (velocity) of rolling bearings above by laboratory, manufacturer and users. Its clauses include term and definitions; physical quantity and unit; assessment of bearing vibration (velocity); test conditions.
Found what you need?
Document preview — JB/T 5313-2001
National Standard of the People's Republic of China
- Replacing
- JB/T 5313-1991
Issued by: Ministry of Industry and Information Technology of the People's Republic of China
Contents
- Foreword3
- 1 Scope4
- 2 Normative References4
- 3 Term and Definitions4
- 4 Physical Quantity and Unit5
- 5 Assessment of Bearing Vibration (Velocity)5
- 6 Test Conditions5
- 7 Test Method and Procedure11
1 Scope
This standard specifies measuring methods for vibration (velocity) of DN 3~120mm deep groove ball bearings, angular contact ball bearing, tapered roller bearing and cylindrical roller bearing (Types N, NU, NJ and NF).
This standard is applicable to the inspection of the vibration (velocity) of rolling bearings above by laboratory, manufacturer and users.
2 Normative References
The following normative documents contain the provisions which, through reference in this standard, constitute the provisions of this standard. At time of publication, the editions indicated were valid. All the standards will be revised, all parties who reach an agreement according to this standard are encouraged to study whether the latest editions of the following standards are applicable.
GB/T 307.1-1994 Rolling Bearings - Radial Bearings - Tolerances
GB/T 6930-1986 Rolling bearings - Vocabulary
3 Term and Definitions
3.1 Bearing vibration
All movements with periodic variation are called bearing vibration, except some intrinsic, function-required movements between bearing parts in the rotation.
Bearing vibration measured in this standard refers to: the radial vibration velocity of bearing outer ring -- where the raceway center section is intersected with the cylindrical surface (highest point) outside the outer ring, when inner ring end face of bearing abuts against mandrel shoulder and rotates at some constant rotation speed, and while the outer ring does not rotate but bears certain radial or axial loads.
3.2 Bearing vibration (velocity) value
Under certain rotation speed and test load, it is tested at three equidistant points at the direction of the cylindrical surface circumference outside bearing outer ring and the arithmetic mean of vibration speeds at the high-, medium- and low-frequency band, that is the vibration (velocity) value of this bearing at the corresponding frequency band. If the bearing needs to be tested on both sides, the higher value (mean value of three points) at each frequency band is the vibration (velocity) value of the bearing at this frequency band.
4 Physical Quantity and Unit
The physical quantity for vibration of measured bearing is the radial vibration velocity of bearing outer ring, µm/s.
5 Assessment of Bearing Vibration (Velocity)
5.1 Frequency range
Within 50~10000Hz frequency range, the three measuring frequency bands of bearing vibration (velocity) shall be according to those specified in Table 1.
5.2 Time averaging method
The vibration speed signal at each measuring point shall be measured for not less than
0.5s and not be read until the pointer is still. If the signal is fluctuated, the medium value of the fluctuation range shall be taken.
6 Test Conditions
6.1 Mechanical device
6.1.1 Basic vibration
Start main drive axle (each frequency band range switch placed at minimum gear), press transducer measuring point down so that it is at the condition identical to the test mode;
in this case, the indicated values at each frequency band shall be in accordance with those specified in Table 2.
6.1.5 Transducer holder
The transducer holder may move along axis direction and vertical direction of main drive axle separately, and ensure that the action line of the transducer on contact load of measured bearing outer ring has an included angle not greater than 2° with vertical line of main drive axle center, the distance off the axial line shall be less than 0.2mm.
6.2 Transducer
What is induced by the transducer is the rate of change in radial vibration displacement of bearing outer ring.
6.2.1
Within 50~10000Hz frequency range, the transducer and the measured bearing outer ring shall be free from separation, and the contact load of transducer for the measured bearing outer ring must be less than 0.7N.
6.2.2
The frequency response characteristics of the transducer system shall be within the limit specified in Figure 3.
Figure 3 -- Frequency Response Characteristics of Transducer
6.2.3 Within 5~3000µm/s (r.m.s), the maximum linear deviation of transducer system
......
This preview omits tables, figures, formulas and parts of the technical clauses. The complete document — 15 pages — is available in the English PDF.
Referenced standards
Similar standards
Editions of JB/T 5313
| Edition | Title | Revision | Status |
|---|---|---|---|
| JB/T 5313-2001 | Rolling bearings - Measuring methods for vibration (velocity) | current edition | Current |
| JB/T 5313-1991 | Rolling bearings - Measuring methods for vibration (velocity) | previous edition | Superseded |
This page sells the current edition, JB/T 5313-2001. Earlier editions are listed for reference only.
How to Download JB/T 5313-2001
- 1
Add to cart
Click "Download PDF" on this page and choose "Buy this standard". You can add more standards before checkout.
- 2
Checkout
Enter your email and billing details. Payment is processed securely by Stripe (cards or bank transfer). Prefer bank details? Request a quotation (min. order $300).
- 3
Fast delivery
After payment you'll receive an email confirmation. The English PDF is sent to the same address, usually within minutes and at the latest within 1 business day.
- 4
Invoice included
A tax invoice is attached to the confirmation email. Need a custom invoice? Contact us.
Related Standards
JB/T 10062-2026 — Probes used in ultrasonic flaw detection - Testing methods for performance
JB/T 10096-2026 — Cases for power semiconductor devices - Selection guidance
JB/T 10097-2026 — Case for power semiconductor device
JB/T 5313-2001
$354.00