Valid

JB/T 3165-1999Thermodynamic performance tests of centrifugal and axial blowers and compressors (English PDF)

离心和轴流式鼓风机和压缩机热力性能试验

Preview PDF

This is a limited preview

Buy now to download the full PDF (16 pages)

Need quotation for your management?

Get a formal quotation for JB/T 3165-1999 in 30 minutes.

Issued by

MIIT

Level / Type

Industry · Recommended

Issue date

July 12, 1999

Implementation date

January 1, 2000

Scope

JB/T 3165-1999 is the English-translated version of 离心和轴流式鼓风机和压缩机热力性能试验.

JB/T 3165-1999 is the Chinese machinery industry standard covering thermodynamic performance tests of centrifugal and axial blowers and compressors. It was issued on 12 July 1999 and has been in force since 1 January 2000, replacing JB 3165-1982.

The document is under the responsibility of the Ministry of Industry and Information Technology. This page is published from the official record of the 1999 edition.

The figures, limits and tables the standard contains are those of the document itself, delivered in full with the English translation.

Found what you need?

Document preview — JB/T 3165-1999

National Standard of the People's Republic of China

Replacing
JB 3165-1982

Issued by: Ministry of Industry and Information Technology of the People's Republic of China

Contents

  • [Preview only]
  • 1 Scope
  • 2 Normative References
  • 2.1 Terms
  • 3 Symbols and Description
  • 4 Test Devices and Instruments
  • 5 Test Regulations
  • 6 Calculation of Test Results
  • 7 Test Report

1 Foreword

JB/T 3165-1999 was issued by Ministry of Industry and Information Technology of the People's Republic of China on 12 July 1999.

1.1 The methods of thermodynamic performance test for centrifugal & axial blower and compressor are specified in this standard.

1.2 This standard is applicable to the thermodynamic performance test of centrifugal & axial blower, compressor and exhauster (hereinafter referred to as compressor) with greater than 1.15 pressure ratio and known gas physical parameters.

1.3 The thermodynamic performance parameters of the compressor under design conditions shall be determined through test and calculation.

The relation curves of flow capacity & boost pressure (or pressure ratio) and shaft power & efficiency of the compressor under design speed shall be drawn according to the above performance parameters. If subsection (cylinder) tests are carried out for the compressor, its performance may be presented by the performance curve of each section, or the performance curve of the complete machine may be presented by the superposition of the performance curve of each section (cylinder).

1.4 The requirements are the minimum for the measuring instruments and methods recommended in this standard, and measuring instruments and methods with the same or higher accuracy can also be applied.

2 Scope Preview

JB/T 3165-1999 carries no ICS number and no Chinese Standard Classification code.

This catalogue holds 21,922 other JB/T standards.

Of the 5,298 JB/T standards that do carry an ICS number, 1,460 (28%) fall under ICS 25, in the field of manufacturing engineering.

3 About this standard

Issued by: Ministry of Industry and Information Technology of the People's Republic of China

English translation: about 16 pages

4 Related standards

Standards on related subjects:

GB/T 4976-2017 — Compressors -- Classification

JB/T 6430-2014 — Oil Injected Screw Air Compressor for General Use

GB/T 2888-2008 — Methods of noise measurement for fans blowers compressors and roots blowers

JB/T 7259-2025 — Centrifugal blowers for sintering plants

JB/T 7258-2025 — General purpose centrifugal blowers

JB/T 3771-2025 — Mobile compressor chassis - Technical Specifications

5 Classification and status

Chinese Standard Classification (CCS): J 72

Prefix JB/T: recommended standard.

......
This preview omits tables, figures, formulas and parts of the technical clauses. The complete document — 16 pages — is available in the English PDF.

Referenced standards

Similar standards

Editions of JB/T 3165

EditionTitleRevisionStatus
JB/T 3165-1999Thermodynamic performance tests of centrifugal and axial blowers and compressorscurrent editionCurrent
JB 3165-1982Thermodynamic performance tests of centrifugal and axial blowers and compressorsprevious editionSuperseded

This page sells the current edition, JB/T 3165-1999. Earlier editions are listed for reference only.

How to Download JB/T 3165-1999

  1. 1

    Add to cart

    Click "Download PDF" on this page and choose "Buy this standard". You can add more standards before checkout.

  2. 2

    Checkout

    Enter your email and billing details. Payment is processed securely by Stripe (cards or bank transfer). Prefer bank details? Request a quotation (min. order $300).

  3. 3

    Fast delivery

    After payment you'll receive an email confirmation. The English PDF is sent to the same address, usually within minutes and at the latest within 1 business day.

  4. 4

    Invoice included

    A tax invoice is attached to the confirmation email. Need a custom invoice? Contact us.

Related Standards

English PDF
16 pages
Fast delivery
Invoice included
View Cart

Secure payment via Stripe

Payments accepted

VisaMastercardAmerican ExpressApple PayGoogle PayStripe

JB/T 3165-1999

$235.00