JB/T 11270-2011Assembled steel rack structure for high-bay warehouse - Technical requirements (English PDF)
立体仓库组合式钢结构货架 技术条件
This is a limited preview
Buy now to download the full PDF (15 pages)
Need quotation for your management?
Get a formal quotation for JB/T 11270-2011 in 30 minutes.
Issued by
MIIT
Level / Type
Industry · Recommended
Issue date
December 20, 2011
Implementation date
April 1, 2012
Scope
JB/T 11270-2011 is the English-translated version of 立体仓库组合式钢结构货架 技术条件.
JB/T 11270-2011 is the Chinese standard "Assembled steel rack structure for high-bay warehouse - Technical requirements". Its scope clause reads: This Standard specifies the technical requirements, test methods, testing rules, markings, packaging, transportation and storage of assembled steel rack structure for high-bay warehouse.
This Standard applies to the assembled rack for high-bay warehouse using storage/retrieval machines to store and retrieve cargos through roadways, and the load carrying capacity of unit location does not exceed 3 000 kg.
Found what you need?
Document preview — JB/T 11270-2011
National Standard of the People's Republic of China
Issued by: Ministry of Industry and Information Technology of the People's Republic of China
Contents
- Foreword3
- 1 Scope4
- 2 Normative references4
- 3 Terms and definitions5
- 4 Technical requirements7
- 4.1 Rack structure for high-bay warehouse7
- 4.2 Materials8
- 4.3 Manufacture8
- 4.4 Requirements for overall installation of racking12
- 5 Test methods17
- 5.1 General provisions17
- 5.2 Testing on manufacture precision17
- 5.3 Testing on the overall installation precision of racking19
- 6 Inspection rules21
- 6.1 Component inspection21
- 6.2 Overall installation inspection of racking22
- 7 Marking, packaging, transportation and storage23
- 7.1 Marking23
- 7.2 Packaging, transportation23
- 7.3 Storage24
1 Scope
This Standard specifies the technical requirements, test methods, testing rules, markings, packaging, transportation and storage of assembled steel rack structure for high-bay warehouse.
This Standard applies to the assembled rack for high-bay warehouse using storage/retrieval machines to store and retrieve cargos through roadways, and the load carrying capacity of unit location does not exceed 3 000 kg.
2 Normative references
The following referenced documents are indispensable for the application of this document. For dated references, only the dated edition cited applies. For undated references, the latest edition of the referenced document (including all amendments) applies.
GB/T 700-2006 Carbon structural steels
GB/T 1231 Specifications of high strength bolts with large hexagon head, large hexagon nuts, plain washers for steel structures
GB/T 1591-2008 High strength low alloy structural steels
GB/T 3098.1-2010 Mechanical properties of fasteners - Bolts, screws and studs
GB/T 3632 Sets of torshear type high strength bolt hexagon nut and plain washer for steel structures
GB/T 5117 Carbon steel covered electrodes
GB/T 5118 Low alloy steel covered electrodes
GB/T 8110 Welding electrodes and rods for gas shielding arc welding of carbon and low alloy steel
GB/T 9286-1998 Paints and varnishes - Cross cut test for films
GB/T 10045 Carbon steel flux cored electrodes for arc welding […]
3.6 diagonal brace
Diagonal member installed in upright frames.
3.7 beam
Main component vertically connected to uprights, directly bearing the vertical load of the cargos in the cell, generally arranged along the X-direction.
3.8 beam connector
Connector fixed to the end of beams, and connected to uprights.
3.9 horizontal bracing
Paired diagonal members horizontally arranged at every certain height, so as to connect the adjacent upright frames together, in order to increase the overall rigidity of the rack structure in the horizontal plane.
3.10 back bracing
Paired diagonal members arranged on the cell back of suitable location, so as to connect the adjacent upright frames together, in order to increase the overall rigidity of the rack structure in the vertical plane.
3.11 bracket
Overhang connector connected to uprights, with pallet rails installed at its end.
3.12 pallet rail
Rail connected to brackets, used to place pallets, along the storage/retrieval direction of storage/retrieval machine folks.
3.13 […]
4.2 Materials
4.2.1 Requirements for main material
4.2.1.1
The main load-bearing structure of racking shall be made of steel with the
mechanical properties not less than those of Q235 steel in GB/T 700-2006.
4.2.1.2
The rack structure for ambient temperature equal to or lower than -20 °C shall be made of steel with the mechanical properties not less than those of 16Mn steel in
GB/T 1591 2008 or Q235-D grade steel in GB/T 700- 2006, and 16Mn steel shall have qualification guarantee of -40 °C Charpy impact test.
4.2.2 Requirements for steel surface
The depth of rust, pitting or scratches on the steel surface shall not exceed half the negative deviation of the steel thickness, and there shall be no delamination fault at the fracture.
4.2.3 Requirements for bolts
4.2.3.1
High strength bolts for racking assembly shall comply with the provisions of
GB/T 1231, GB/T 3098.1-2010 (Class 8.8) or GB/T 3632.
4.2.3.2
Anchor bolts should use expansion anchor bolts or chemical bolts.
4.3 Manufacture
4.3.1 Requirements for upright punching
The upright punching spacing should be 50 mm, 75 mm and 100 mm.
4.3.2 Requirements for rolling
4.3.2.1
After the rolling of components, there shall be no cracks on the steel surface.
4.3.2.2
After the rolling of cross-type beams, the outer edge of the joint shall be tightly closed.
4.3.3 Requirements for cutting of components
The cutting of components shall strictly guarantee the component precision and the incision shall be neat; there shall be no flashes and burrs; the cross-section shall not be significantly deformed.
4.3.4 Requirements for straightness of components
After the component is cut, its straightness is L/1 000 (L is the cutting length).
4.3.5 Manufacture of bolt holes
5.3.4 Testing on the installation precision of running rails and guide rails
5.3.4.1 Distance between running rails and guide rails
Directly measure at the top tie of guide rails with a steel tape.
5.3.4.2 Horizontal dislocation
Measure at the top tie of guide rails by plumb bob method.
5.3.5
Testing on the height deviation of bracket pallet rails or beams in the same level of the racking
Directly measure on the top of bracket pallet rails or beams with a levelling ruler and feeler gauge.
5.3.6 Verticality deviation of upright frames
Measure at the highest point of upright frames by plumb bob method.
5.3.7
Testing on the deviation of the center-to-center distance at the bottom of uprights of adjacent upright frames
Directly measure at the bottom of racking with steel tapes or rulers.
5.3.8
Testing on the deviation of the dimension of B1, B2 (see Figure 6) with the center line of running rail as datum
Measure at the bottom of uprights of upright frames with rulers.
5.3.9
Testing on the deviation of the dislocation of upright frames in the same ray and in the same roadway
Measure with squares, rulers, with the center line of the running rail as the datum.
5.3.10 Testing on surface spraying quality
5.3.10.1 Testing on appearance quality
The surface spray quality shall be tested by visual inspection method.
5.3.10.2 Testing on coating thickness
The surface coating thickness shall be tested by thickness gauges.
5.3.10.3 Testing on coating adhesion
6.1.2.2
The inspection items of uprights are as follows:
a) The spacing of the first and the last holes of uprights;
b) The width of uprights;
c) The inside and outside bending of uprights.
6.1.2.3
The inspection item of beams is as follows:
The net length of beams.
6.1.2.4
The inspection item of brackets is as follows:
The net length of brackets.
6.1.2.5
Assemble the upright frames on site; after assembly, the inspection items are as follows:
a) The full length of upright frames;
b) The width of upright frames;
c) The height difference of upright frames’ baseplates;
d) The verticality of the upright of upright frames and the floor;
e) The position dimension of each bolt hole.
6.2 Overall installation inspection of racking
The overall installation inspection items are as follows:
a) The installation precision of running rails;
b) The installation precision of guide rails;
c) The vertical distance deviation between running rails and guide rails;
d) The horizontal dislocation of running rails and guide rails (measured in Z- direction):
e) The height deviation of bracket pallet rail or beams in the same level of racking;
f) The verticality of the upright frames in Z-direction and the position limit deviation in X-direction;
g) The deviation of center-to-center distance at the bottom of uprights of adjacent upright frames;
......
This preview omits tables, figures, formulas and parts of the technical clauses. The complete document — 15 pages — is available in the English PDF.
Referenced standards
Cited by
- GB/T 41514-2022Standard for safety and evaluation of steel structure racks
- GB/T 39681-2020Racking design code for steel static storage systems
- WB/T 1073-2018Self supported racking
- WB/T 1076-2018Cold storage racking
- JB/T 5323-2017Welded steel racks for automated warehouses - Technical requirements
- WB/T 1066-2017Technological conditions of rack installation and acceptance
Similar standards
How to Download JB/T 11270-2011
- 1
Add to cart
Click "Download PDF" on this page and choose "Buy this standard". You can add more standards before checkout.
- 2
Checkout
Enter your email and billing details. Payment is processed securely by Stripe (cards or bank transfer). Prefer bank details? Request a quotation (min. order $300).
- 3
Fast delivery
After payment you'll receive an email confirmation. The English PDF is sent to the same address, usually within minutes and at the latest within 1 business day.
- 4
Invoice included
A tax invoice is attached to the confirmation email. Need a custom invoice? Contact us.
Related Standards
JB/T 10062-2026 — Probes used in ultrasonic flaw detection - Testing methods for performance
JB/T 10096-2026 — Cases for power semiconductor devices - Selection guidance
JB/T 10097-2026 — Case for power semiconductor device
JB/T 11270-2011
$125.00