HJ 2550-2018Technical requirement for environmental labeling products - Disinfecting tableware cabinet (English PDF)

3.1 Disinfecting of tableware

Kill or remove residual pathogenic microorganisms from cleaned natural utensils to achieve harmless treatment.

[GB 17988-2008, definition 3.101]

3.2 Disinfecting tableware cabinet

Appropriate volume and equipment, using physical, chemical or a combination of both to disinfect utensils. It has a place to place utensils One or more compartments.

[GB 17988-2008, definition 3.102]

3.3 Recycling rate recycling rate

The sum of the mass of the reusable part and the recycled part (excluding the energy recovery part) expected in the electrical and electronic products the percentage of total mass of electrical and electronic products.

[GB/T 32355.2-2015, definition 3.1]

3.4 Shutdown mode off made

When the product's power supply is connected to the mains, no standby mode, network mode, or active mode appears, and any Product model. Only the indicator that the user's product is in the shutdown position is included in the category of the shutdown mode.

[GB/T 35758 -2017, definition 3.5]

3.5 Standby mode standby mode

The energy-using appliance provides one or more of the following user-oriented or protection functions when connected to the main power source, and is continuous for any Product model.

-- Other modes (including active) can be triggered by triggering remote switches (including remote control), internal sensors, and timers Mode is on or off);

-- Continuous function. information or status display including the clock;

-- Continuous function. sensor based function [GB/T 35758-2017, definition 3.6]

5.1 Product Environmental Design Requirements

5.1.1 Easy to recycle design

5.1.1.1 The product recyclability should be no less than 75%.

5.1.1.2 Plastic parts with a mass greater than 25g or a surface area exceeding.200mm2 shall be marked in accordance with the requirements of GB/T 16288.

5.1.2 Restricted/disabled substance requirements

5.1.2.1 Lead (Pb), cadmium (Cd), mercury (Hg), hexavalent chromium (Cr6), polybrominated biphenyls (PBBs) and polybrominated diphenyl ethers (PBDEs) in products the content should meet the requirements of GB/T 26572.

5.1.2.2 Products with UV disinfection function, the mercury content in the UV lamp used is not more than 15mg per lamp.

5.1.2.3 The product shell, the substrate of the circuit board, and the power cord do not use short-chained chlorinated paraffins (SCCPs), and the content should be no more than the plastic zero.

0.1% of the total parts.

5.1.2.4 Except for sealing parts, plastic parts with a mass greater than 25g do not use chlorine-containing polymers; do not contain tris(2-chloroethyl) Ester (TCEP), tris(2-chloropropyl) phosphate (TCPP), tris(2,3-dichloropropyl) phosphate (TDCP) and hexabromocyclohexane A flame retardant for dodecane.

5.1.2.5 Except for the power cord, the phthalate esters listed in Appendix A are not used in plastic parts with a mass greater than 25g.

More than 1000mg/kg.

5.1.2.6 The maximum allowable limit of benzo[a]pyrene in the product casing, buttons and power cord is 20 mg/kg, and the sixteen items listed in Appendix B the total amount of cyclic aromatic hydrocarbons (PAHs) does not exceed.200 mg/kg.

5.1.2.7 The product does not use hydrochlorofluorocarbons (HCFCs) as blowing agents.

5.1.3 The coating used in the product shall meet the requirements of the anti-corrosion coating in HJ 2537.

5.2 Product production process requirements

5.2.1 No use of hydrochlorofluorocarbons (HCFCs), 1,1,1-trichloroethane (C2H3Cl3), dichloroethane (CH3CHCl2), trichloroethylene (C2HCl3), carbon tetrachloride (CCl4), chloroform (CHCl3), dichloromethane (CH2Cl2), bromopropane (C3H7Br), toluene (C7H8), xylene (C6H4(CH3)2) as a cleaning solvent.

5.2.2 Welding during assembly and joining process shall be carried out by lead-free soldering.

5.3 Product requirements

5.3.1 The disinfection effect of at least one chamber of the product should meet the two-star requirement of GB 17988.

5.3.2 For products with ozone disinfection function, the average ozone leakage during the whole ozone disinfection cycle is not more than 0.16mg/m3.

5.3.3 The shutdown power and standby power of the product shall comply with the requirements of Table 1.

Table 1 Product shutdown power, standby power

Project limit/W

Shutdown mode <=0.5

Standby mode

Status display <=1

Stateless display <=0.5

5.4 Product packaging requirements

5.4.1 The total amount of heavy metals such as lead, cadmium, mercury and hexavalent chromium in packaging and packaging materials shall not exceed 100 mg/kg.

5.4.2 Product packaging should be marked according to GB/T 18455.

5.4.3 Recyclable packaging materials should be used.

5.5 Product Description Requirements

The product description shall be delivered to the user together with the product, and shall meet the requirements of the GB 17988 product description at the same time.

Prompt description of product recycling process. Among them, the treatment, disposal and recycling of mercury in the product UV lamp conform to GB/T 23685 Requirements.