HG/T 21574-2018Code for design and selection of lifting lugs for chemical equipment (English PDF)
化工设备吊耳设计选用规范
This is a limited preview
Buy now to download the full PDF (104 pages)
Need quotation for your management?
Get a formal quotation for HG/T 21574-2018 in 30 minutes.
Issued by
MIIT
Level / Type
Industry · Recommended
Issue date
April 30, 2018
Implementation date
September 1, 2018
Scope
HG/T 21574-2018 is the English-translated version of 化工设备吊耳设计选用规范.
HG/T 21574-2018 is the Chinese standard "Code for design and selection of lifting lugs for chemical equipment". Its scope clause reads: This standard is specially formulated to ensure the safety of chemical equipment during hoisting and to design and select lifting lugs reasonably.
This standard is applicable to material selection, design, manufacture, inspection and acceptance of lifting lugs for steel chemical equipment and its components during equipment lifting.
This standard specifies the classification, type code, dimension, material, technical requirements of lifting lugs for lifting chemical equipment or its components, and the check and calculation of lifting lugs body and chemical equipment during hoisting.
In addition to this standard, the material selection, design, manufacture, inspection and acceptance of chemical equipment lifting lugs shall also meet the requirements in the current relevant national standards.
Its clauses include general; terms and symbols; classification and layout for lifting lugs; application scope and selection principle for lifting lug.
Found what you need?
Document preview — HG/T 21574-2018
National Standard of the People's Republic of China
- ICS
- 71.120
- Replacing
- HG/T 21574-2008
Issued by: Ministry of Industry and Information Technology of the People's Republic of China
Contents
- Foreword i
- 1 General
- 2 Terms and symbols
- 2.1 Terms
- 2.2 Symbols
- 3 Classification and layout for lifting lugs
- 3.1 Classification for lifting lugs
- 3.2 Layout for lifting lugs
- 4 Application scope and selection principle for lifting lug
- 4.1 Application scope for lifting lugs
- 4.2 General procedures for selecting lifting lugs
- 5 Technical requirements
- 5.1 Design
- 5.2 Material
- 5.3 Manufacture
- 5.4 Inspection and acceptance
- 6 Mark
- 7 Top head lug
- 8 Horizontal vessel lug
- 9 Side plate-type lug
- 10 Trunnion
- 11 Tailing lug
- Annex A Design of lifting lugs
- Annex B Requirements of minimum thickness
- Annex C Calculation and check of stress bearing during equipment hoisting
- Annex D Inner ring bracing type and check of equipment skirt
- Annex E Lifting lug for parts and components
- 2. The clause “application scope” is revised and merged into the clause “general provisions”;
- 3. The terms and symbols clauses are added;
- 4. The applicable nominal lifting weight scope of lifting lugs is expanded;
- 5. The total factor is adjusted;
- 7. The application scope of materials with minimum thickness is added;
- 2.1.
1 General
1.0.1
This standard is specially formulated to ensure the safety of chemical equipment during hoisting and to design and select lifting lugs reasonably.
1.0.2
This standard is applicable to material selection, design, manufacture, inspection and acceptance of lifting lugs for steel chemical equipment and its components during equipment lifting.
1.0.3
This standard specifies the classification, type code, dimension, material, technical requirements of lifting lugs for lifting chemical equipment or its components, and the check and calculation of lifting lugs body and chemical equipment during hoisting.
1.0.4
In addition to this standard, the material selection, design, manufacture, inspection and acceptance of chemical equipment lifting lugs shall also meet the requirements in the current relevant national standards.
2 Terms and symbols
2.1 Terms
2.1.1 lifting lug
parts such as lifting ropes and hooks welded to the equipment for fixing and lifting equipment
2.1.2 top head lug
lifting lug that is welded on top seal head of vertical equipment and made of steel plate
2.1.3 horizontal vessel lug
lifting lug that is welded to the cylindrical section of horizontal equipment and made of steel plate
2.1.4 side plate-type lug
lifting lug that is welded on upper part and top seal head of cylindrical section of vertical equipment and made of steel plate
2.1.5 trunnion
lifting lug that is welded to the cylindrical section of equipment and made of steel pipes or coiled steel plates
2.1.6 tailing lug
lifting lug that is welded to the lower part of vertical equipment and made of steel plates
2.1.7 hoisting
operation procedure in which equipment is lifted and installed at the specified position under the action of hoisting machinery
2.1.8 nominal lifting capability
maximum lifting weight (in t) allowed by a single lifting lug during hoisting lug design or selection
2.1.9 lifting weight of equipment
maximum weight of equipment during hoisting, including the weight of accessories lifted with the equipment, such as ladders, platforms, insulation and auxiliary pipelines, etc.
2.1.10 impact factor
ratio of dynamic load to static load considered during hoisting
2.1.11 unbalance factor
unevenness of load distribution among the lifting lugs considered during hoisting
2.1.12 total factor
amplification coefficient relative to static load determined by comprehensively determining dynamic load, unbalance and other influencing factors during lifting lug strength check, the value of which shall not be less than the product of unbalance factor and dynamic load factor
2.1.13 pad eye
circular plate welded on both sides of the lifting hole for reinforcement
2.1.14 shackle
combination formed by assembling buckle and pin shaft
2.1.15 pin
circular section pin in conjunction with buckle
2.1.16 sling angle
included angle between the sling and the vertical direction during hoisting, for the plate-type lug, this standard only considers the case that the sling is in the plane of the lifting lug plate
2.1.17 rifting angle
included angle between the equipment axis and the horizontal direction during hoisting, generally taking 0° when the equipment is in a horizontal state and 90° when the equipment is in a vertical state
2.2 Symbols
2.2.1 Geometrical characteristics
D - - the diameter of plate-type lug hole, mm;
D0 - - the outer diameter of trunnion pipe axis, mm.
D1 - - the outer diameter of pad eye mm;
dr - - the diameter of pin, mm;
h - - the calculated thickness of fillet weld, when there is a backing plate, take the smaller of 0.56S1 and 0.7delta. When there is no backing plate, take 0.7delta, mm;
n - - the number of lifting lugs, pcs;
S - - the thickness of plate-type lug or trunnion pipe axis, mm;
S1 - - the thickness of backing plates, mm;
S2 - - the thickness of pad eye, mm;
W - - the effective weight (equal to WL/n) of single lifting lug design, kg;
Wn - - the nominal lifting capability, ×103kg;
WL - - the lifting weight of equipment, kg;
alpha - - the sling field angle, the included angle between sling and vertical direction, °;
delta - - the negative deviation of results obtained thorough nominal thickness of the seal head or cylindrical section at the lifting lug minus the thickness of material, mm; theta - - the rifting angle (°) included between equipment axis and horizontal direction.
2.2.2 Loads, material and the like
E - - the elastic modulus of lifting lugs material, MPa;
Fh - - the transverse calculated load, N;
FL - - the calculation load of sling N;
Fv - - the vertical calculated load, N;
g - - the gravitational acceleration, m/s2;
K - - the total factor of hoisting;
Kd - - the impact factor, taking 1.2;
Ku - - the unbalance factor, taking 1.125;
ReL - - the typical yield strength at room temperature of metallic material, MPa;
v - - the poisson's ratio of lifting lugs material, taking 0.3;
sigmahz - - the maximum compressive stress at the lifting hole, MPa;
[sigma] - - the allowable tensile stress of lifting lugs material, taking ReL/1.6, MPa;
[sigmahz] - - the allowable compressive stress of lifting lugs material, taking 2ReL, MPa;
[ ] - - the allowable shear stress of lifting lug material, taking 0.6[sigma], MPa;
[sigmae] - - the allowable tensile stress of equipment material, MPa;
[ ] - - the allowable shear stress of equipment material, MPa;
Phia - - the fillet weld coefficient, taking 0.7.
3 Classification and layout for lifting lugs
3.1 Classification for lifting lugs
3.1.1
This standard contains the following five types of lifting lugs:
1 Top head lug (Types TPA and TPB);
2 Horizontal vessel lug (Type HP);
3 Side plate-type lug (Type SP);
4 Trunnion (Types AXA, AXB and AXC);
5 Tailing lug (Types APA and APB).
3.1.2
See Table 3.1.2 for the classification, diagrams and codes of various lifting lugs.
Table 3.1.2 Classification, diagrams and codes of lifting lugs
Type Type code Diagram of lifting lug Type code
Top head lug
TP TPA TPB Horizontal vessel lug
HP HP Side plate-type lug SP SP Trunnion AX AXA AXB AXC Tailing lug AP APA APB
3.2 Layout for lifting lugs
3.2.1 Layout of top head lug
1 Two top head lugs should be symmetrically installed on the elliptical head, dish head, spherical head without folded edge or hemispherical head at the top of the vertical equipment, Under special circumstances, the number of lifting lugs shall be more than 2. For elliptical head and dish head, the position of the lifting lug shall be adjusted according to actual needs, but the centerline of the lifting lug should be located within the range of 0.7 times the diameter of the head. When TP-type lifting lugs are arranged on the flat head or conical head at the top of the equipment, the strength of the head shall be checked according to the load of the lifting lugs.
2 The layout of the top head lug is shown in Figure 3.2.1.
Type I Type II Figure 3.2.1 Layout of top head lug 3.2.2 The layout of horizontal vessel lug is shown in Figure 3.2.2.
Type I
Type II Type III Figure 3.2.2 Layout of horizontal vessel lug 3.2.3 Side plate-type lug shall be symmetrically arranged at the top of the cylinder, and the layout is shown in Figure 3.2.3.
Figure 3.2.3 Layout of side plate-type lug 3.2.4 The trunnion shall be arranged above the center of gravity of the equipment. Such factors as equipment and ancillary structure, equipment stress during hoisting and lifting space shall be considered for the specific location. The typical layout is shown in Figure 3.2.4.
Figure 3.2.4 Layout of trunnion 3.2.5 The layout of tailing lug should meet the following requirements:
1 The tailing lug should be installed at the bottom of the skirt, and the end of the lifting lug shall be welded on the shell of the skirt, and when the cover plate of the anchor bolt seat is divided into blocks or those without a plate, the lower edge shall be welded on the base ring plate; when the cover plate of the anchor bolt seat is a complete circle, the tailing lug should be placed between the cover plate and the base ring plate, the upper and lower edges shall be welded to the cover plate and the base ring plate respectively. If due to structural restrictions, the tailing lugs may be placed at other position, and the typical layout is shown in Figure 3.2.5.
Figure 3.2.5 Layout of tailing lug
2 When the distance between the cover plate and the base ring plate is greater than H, H may be increased so that the lifting lug shall be welded to the cover plate and the base ring plate;
Note: see Figure 11.0.1 for H and L.
3 APA- or APB-type should be selected for the tailing lugs according to the nominal lifting weight, and located in the center of the lifting lug of the two upper equipment.
4 Application scope and selection principle for lifting lug
4.1 Application scope for lifting lugs
4.1.1
See Table 4.1.1-1 for the application scope of lifting lugs. See Table 4.1.1-2, Table 4.1.1-3 and Table 4.1.1-4 for the direct selection of the minimum thickness required for the shell.
......
This preview omits tables, figures, formulas and parts of the technical clauses. The complete document — 104 pages — is available in the English PDF.
Referenced standards
Normative references
- GB/T 196General purpose metric screw threads - Basic dimensions
- GB/T 197General purpose metric screw threads -- Tolerances
- GB/T 1804General tolerances - Tolerances for linear and angular dimensions without individual tolerance indications
- GB/T 3274Hot-rolled plates, sheets and strips of carbon structural steels and high strength low alloy structural steels
- GB/T 8163Seamless steel pipes for liquid service
- GB/T 150.2Pressure vessels - Part 2: Materials
Similar standards
Editions of HG/T 21574
| Edition | Title | Revision | Status |
|---|---|---|---|
| HG/T 21574-2018 | Code for design and selection of lifting lugs for chemical equipment | current edition | Current |
| HG/T 21574-2008 | Code for design and selection of lifting lugs for chemical equipment | previous edition | Superseded |
This page sells the current edition, HG/T 21574-2018. Earlier editions are listed for reference only.
How to Download HG/T 21574-2018
- 1
Add to cart
Click "Download PDF" on this page and choose "Buy this standard". You can add more standards before checkout.
- 2
Checkout
Enter your email and billing details. Payment is processed securely by Stripe (cards or bank transfer). Prefer bank details? Request a quotation (min. order $300).
- 3
Fast delivery
After payment you'll receive an email confirmation. The English PDF is sent to the same address, usually within minutes and at the latest within 1 business day.
- 4
Invoice included
A tax invoice is attached to the confirmation email. Need a custom invoice? Contact us.
Secure payment via Stripe
Payments accepted
HG/T 21574-2018
$1,775.00