GB/Z 45864.2-2025Earth-moving machinery - Collision warning and avoidance - Part 2: On-board J1939 communication interface (English PDF)
土方机械 碰撞警告和避免 第2部分:车载J1939通信接口
This is a limited preview
Buy now to download the full PDF (76 pages)
Need quotation for your management?
Get a formal quotation for GB/Z 45864.2-2025 in 30 minutes.
Issued by
SAMR; SAC
Level / Type
National · Recommended
Issue date
December 3, 2025
Implementation date
December 3, 2025
Scope
GB/Z 45864.2-2025 is the English-translated version of 土方机械 碰撞警告和避免 第2部分:车载J1939通信接口.
GB/Z 45864.2-2025 is a guiding technical document describing the on-board link that lets a connected device command an earth-moving, mining or road-construction machine to slow down, stop or stay still.
It defines the logical and physical interfaces and the SAE J1939 message set through which a collision avoidance system, standalone or built into the machine, delivers intervention signals, and the same protocol can feed a collision warning system; informative annexes cover the communication procedure, a certificate-exchange trust mechanism between machine and device, and examples of overclocking and standby modes.
For machines that slew or combine motions, such as excavators, only the linear part of travel is addressed. It does not cover plug-and-play fitting of such systems and does not rule out other interfaces.
The document adopts ISO/TS 21815-2:2021 identically and was issued 3 December 2025.
Found what you need?
Document preview — GB/Z 45864.2-2025
National Standard of the People's Republic of China
- ICS
- 53.100
- Classification
- P 97
Issued by: State Administration for Market Regulation; Standardization Administration of the PRC
Contents
- Preface
- Introduction
- 1.Scope
- 2 Normative References
- 3.Terms and Definitions
- 4.Symbols and Abbreviations
- 5.Logical Interface
- 6 Physical Interfaces
- 7 J1939 Communication Protocol
- 8 Document
- Appendix A (Informative) Communication Procedure
- Appendix B (Informative) Trust Mechanism
- Appendix C (Informative) Implementation Examples of Overclocking and Standby Modes
- References
Foreword
This document is a standard or guiding technical document.
This document complies with the provisions of GB/T 1.1-2020 "Standardization Work Guidelines Part 1: Structure and Drafting Rules of Standardization Documents". Drafting.
This document is Part 2 of GB/T 45864 "Warning and Avoidance of Collisions with Earthmoving Machinery". GB/T 45864 has the following... part.
---Part 1: General Requirements;
---Part 2: Vehicle-mounted J1939 Communication Interface;
---Part 3: Risk Zones and Risk Levels for Moving Forward/Backward
This document is equivalent to ISO /T S21815-2.2021 "Earthmoving machinery - Collision warning and avoidance - Part 2: Onboard J1939 communication". interface".
Introduction
The increasing use of detection systems and obstacle avoidance technologies has been supporting drivers in safely operating machinery in the mining and construction industries. Meanwhile, it is necessary to... Standards should be established for the detection, alarming, and intervention of machines and systems to mitigate the risk of collisions.
Currently, there are two existing standards in this field. ISO 16001 and ISO 17757. These two standards cover object monitoring systems and their visual aids.
The devices, as well as autonomous and semi-autonomous machines, provide guidance, but there are currently no standards describing the collision risks associated with human-operated machines.
Collision risk awareness, warning signals, and collision avoidance measures.
The collision warning and avoidance system is undergoing technical updates; moreover, these algorithms are still immature and not well understood. This document... The aim is to promote innovation and accelerate the pace of improvement in new collision warning and avoidance technologies. The performance requirements in this document are technology-neutral and do not specify requirements to be met. The required technology.
The system described in this document is designed to assist the machine driver. However, current technology cannot achieve complete collision warning in every situation.
Warning/Avoidance. The safe operation of the machine remains the responsibility of the machine operator.
This document defines the communication protocol between the machine and the connected device to allow the connected device to command the machine to move linearly along the travel path (i.e., To decelerate, stop, or remain stationary in the forward or backward direction. This applies to machines with rotary motion (such as excavators) and machines with combined motions.
(The machine with the moving arm) only considers the linear component range of its stroke.
Machine manufacturers have the flexibility to decide which method best suits their machines. Some applications can provide basic functionality (e.g.,...).
(For example, without using registers). Regardless of the method chosen, the connected device has a way to discover machine functionality.
Appendix B outlines the mechanisms by which certificate exchange, as defined by the machine manufacturer, establishes trust between a machine and a connected device. Session Layer The message structure may differ from the message structure defined in this file.
The J1939 protocol specification in this document does not preclude the development of other communication interfaces that can support collision warning and avoidance functions. (This is in the context of the publication of this document.)
At that time, since CAN2.0 interfaces are widely available on machinery and equipment that provide collision warning and avoidance functions, only SAE J1939 is required.
The protocol was defined.
GB/T 45864 "Warning and Avoidance of Collisions with Earthmoving Machinery" is a series of standards, which is planned to consist of five parts.
---Part 1: General Requirements. The purpose is to provide automated intervention controls and testing mechanisms for object detection, operator warnings, and collision avoidance.
General requirements for the verification process.
---Part 2: Vehicle-mounted J1939 Communication Interface. The purpose is to describe the connection equipment used in earthmoving, mining, and road construction applications.
An onboard communication interface between the equipment and the mobile machine to implement the interventional collision avoidance measures defined in Part 1.
---Part 3: Risk Zones and Risk Levels for Forward/Reverse Movement. The purpose is to outline the overall requirements for collision avoidance alarm devices and clarify... The warnings and intervention actions that the anti-collision alarm device should issue when moving forward or backward.
---Part 4: Risk Areas and Risk Levels of Oscillating/Rotating Motion. The purpose is to propose collision prevention measures for machines during oscillating/rotating motion.
The alarm device should issue warnings and take intervention actions.
---Part 5: Hazard Areas and Hazard Levels for Other Forms of Motion. The purpose is to identify hazards other than forward/backward movement, swinging/turning.
Collision avoidance requirements for other forms of motion;
The relevant provisions in Parts 2 through 5 shall be used in conjunction with the general requirements in Part 1 in order to better meet the application requirements.
1 Scope
This document describes the vehicle-mounted communication interface between connecting devices and mobile machinery used in earthmoving, mining, and road construction applications.
Implements the interventional collision avoidance measures defined in ISO 21815-1.Based on the SAE J1939 protocol, this interface uses a standalone interface integrated into the original machine.
The collision avoidance system (CAS) of the machine provides intervention signals to slow down, stop, or prevent machine movement. The protocols defined in this document can also be used... Provide input information for the Collision Warning System (CWS).
This document does not apply to plug-and-play implementations of CAS or CWS on machines. CAS or CWS manufacturers and machine manufacturers may agree on this.
Other details not fully described in this document are required to implement the functionality.
This document does not rule out the possibility that machine manufacturers or CxD manufacturers may develop alternative in-vehicle communication interfaces.
2 Normative references
The contents of the following documents, through normative references within the text, constitute essential provisions of this document. Dated citations are not included.
For references to documents, only the version corresponding to that date applies to this document; for undated references, the latest version (including all amendments) applies. This document.
ISO 19014-3 Functional safety of earthmoving machinery - Part 3: Safety of control systems - Electronic and electrical components used in related parts Environmental adaptability and testing requirements (Earth-movingmachinery-Functionalsafety-Part 3: Environmental per-) the control system)
3 Terms and Definitions
The following terms and definitions apply to this document.
3.1 Collision warning system (CWS)
A system that detects anticipated targets in a collision hazard zone, determines the level of collision risk, and provides warnings to the driver.
[Source: ISO 21815-1:2022, 3.8]
3.2 Collision avoidance system (CAS)
A system for detecting anticipated targets in a collision hazard zone, determining the collision risk level, and providing interventional collision avoidance measures.
[Source: ISO 21815-1:2022, 3.9]
3.3 CxS
Collision warning system (CWS) (3.1) or collision avoidance system (CAS) (3.2) or a system that provides both.
[Source: ISO 21815-1:2022, 3.10]
......
This preview omits tables, figures, formulas and parts of the technical clauses. The complete document — 76 pages — is available in the English PDF.
Referenced standards
Normative references
ISO 19014-3
Similar standards
How to Download GB/Z 45864.2-2025
- 1
Add to cart
Click "Download PDF" on this page and choose "Buy this standard". You can add more standards before checkout.
- 2
Checkout
Enter your email and billing details. Payment is processed securely by Stripe (cards or bank transfer). Prefer bank details? Request a quotation (min. order $300).
- 3
Fast delivery
After payment you'll receive an email confirmation. The English PDF is sent to the same address, usually within minutes and at the latest within 1 business day.
- 4
Invoice included
A tax invoice is attached to the confirmation email. Need a custom invoice? Contact us.
Related Standards
GB/Z 102.17-2026 — Semiconductor devices - Discrete devices - Part 17: Magnetic and capacitive coupler for basic and reinforced insulation
GB/Z 103-2026 — Health informatics - The architecture of internet healthcare service network
GB/Z 108-2026 — Health informatics - Internet healthcare service pattern
GB/Z 45864.2-2025
$1,160.00