GB/T 9966.18-2021Test methods for natural stone—Part 18: Petrographic examination (English PDF)
天然石材试验方法 第18部分:岩相分析
This is a limited preview
Buy now to download the full PDF (15 pages)
Need quotation for your management?
Get a formal quotation for GB/T 9966.18-2021 in 30 minutes.
Issued by
SAMR; SAC
Level / Type
National · Recommended
Issue date
April 30, 2021
Implementation date
November 1, 2021
Scope
GB/T 9966.18-2021 is the English-translated version of 天然石材试验方法 第18部分:岩相分析.
GB/T 9966.18-2021 is Part 18 of the Chinese national test methods for natural stone and covers the petrographic examination of stone. The rock is identified from its mineral composition and structure, observed with the naked eye and under a polarizing microscope on the basis of the physical and optical characteristics of the minerals.
The standard lists the rock slicer, the grinding mill and the microscope, and describes how thin sections are prepared, including their orientation for anisotropic stone and resin reinforcement of weak specimens.
It then sets what the visual and microscopic descriptions must record, how the stone type is judged against GB/T 13890, with other methods such as X-ray diffraction where the description is not enough, and the content of the test report. It was issued on 30 April 2021 and has applied since 1 November 2021.
Found what you need?
Document preview — GB/T 9966.18-2021
National Standard of the People's Republic of China
- ICS
- 91.100.15
- Classification
- Q 21
Issued by: State Administration for Market Regulation; Standardization Administration of the PRC
Contents
- Foreword
- 1 Scope
- 3 Principles
- 4 Instruments and Equipment
- 5 Sample Preparation
- 6 Description of visual observation
- 7 Microscopic Observation Description
- 8 Judgment
- 9 Test Report
Foreword
GB/T 9966 "Test Methods for Natural Stone" is divided into 18 parts.
Part 1: Compression strength test after drying, water saturation, and freeze-thaw cycles;
Part 2: Bending strength test after drying, water saturation, and freeze-thaw cycles;
Part 3: Water absorption, bulk density, true density, and true porosity tests;
Part 4: Abrasion Resistance Test;
Part 5: Hardness Test;
Part 6: Acid Resistance Test;
Part 7: Strength Test of Stone Hanging Component Assembly Unit.
Part 8: Test Method for Structural Strength Testing of Stone Hanging Systems Using Uniform Static Pressure Difference;
Part 9: Determination of dynamic elastic modulus by measuring the fundamental resonant frequency;
Part 10: Determination of the seismic performance of the hanger assembly unit;
Part 11: Determination of Accelerated Aging Strength Due to Rapid Cooling and Heating;
Part 12: Determination of Static Modulus of Elasticity;
Part 13: Determination of capillary water absorption coefficient;
Part 14: Determination of fracture resistance energy;
Part 15: Determination of Salt Spray Aging Resistance;
Part 16: Determination of the linear thermal expansion coefficient;
Part 17: Determination of Salt Crystallization Strength
Part 18: Lithofacies Analysis.
This part is Part 18 of GB/T 9966.
This section was drafted in accordance with the rules given in GB/T 1.1-2009.
1 Scope
This part of GB/T 9966 specifies the principles, instruments and equipment, sample preparation, visual observation and description, and microscopic analysis of petrographic features in natural stone. Observation, description, judgment, and test report.
This section applies to petrographic analysis of natural stone.
3 Principles
Mineral composition and structure are determined by observing the minerals in the rock with the naked eye and under a microscope, based on their physical and optical characteristics. Petrological properties and lithofacies of stone.
4 Instruments and Equipment
4.1 Rock Slicer
4.2 Rock Grinding Mill
4.3 Polarizing microscope.
5 Sample Preparation
5.1 The specimen should be of sufficient size to represent the characteristics of the mineral being tested. One or more specimen slices should be prepared and adhered to a glass plate. On a glass slide, it is polished with alumina polishing paste of 100µm~10µm grade to a thickness of (0.030 ± 0.005) mm.
5.2 Typically, the sample size is 33 mm x 20 mm. If the stone particles are large, a larger sample size should be used, such as... 75mm x 50mm, or use multiple samples under normal conditions. If the rock exhibits anisotropic characteristics, use two parallel lines. The directions of anisotropic surfaces (such as bedding, foliation, etc.) of the specimen should be clearly marked, and specimens should be prepared according to each direction.
5.3 The specimen should preferably be selected from a portion with sufficient strength to avoid fragmentation during cutting. For specimens with lower strength, an injection refractive index method should be used. Samples are prepared after reinforcement with approximately 1.54% resin (such as epoxy resin).
6 Description of visual observation
The description of visual observation should include the following.
a) Color.
b) Structural features;
c) Structural characteristics, such as large particles, medium particles, and small particles;
d) Surface condition, such as cracks, micropores (holes), fossils, degree of weathering, alteration, etc.
7 Microscopic Observation Description
The description of microscopic observations should include the following.
a) Microstructural features.
b) Mineral and structural characteristics
8 Judgment
The rock type is determined by data obtained from observations of rock grains, structure, and mineral composition using the naked eye and microscope, and then compared with... GB/T 13890 specifies the commercial types of stone samples.
If the petrographic description of a rock cannot provide sufficient evidence for petrographic determination, other analytical methods are needed for confirmation, such as... X-ray diffraction analysis, etc.
9 Test Report
The test report should include at least the following.
a) The commercial name of the stone as specified in GB/T 17670;
b) Quantity, dimensions, and orientation of the anisotropic surface of the specimens;
c) Dates of sample delivery, preparation, and measurement.
d) The name and address of the testing laboratory; if the test is not conducted in a testing laboratory, the location of the test should be noted.
e) The standard number followed in the test (GB/T 9966.18-2021);
f) Description based on visual observation;
g) Description of microscopic observations;
h) Lithofacies determination according to GB/T 13890;
i) Test deviations (such as sampling location and quantity, and grinding discs, etc.).
......
This preview omits tables, figures, formulas and parts of the technical clauses. The complete document — 15 pages — is available in the English PDF.
Similar standards
How to Download GB/T 9966.18-2021
- 1
Add to cart
Click "Download PDF" on this page and choose "Buy this standard". You can add more standards before checkout.
- 2
Checkout
Enter your email and billing details. Payment is processed securely by Stripe (cards or bank transfer). Prefer bank details? Request a quotation (min. order $300).
- 3
Fast delivery
After payment you'll receive an email confirmation. The English PDF is sent to the same address, usually within minutes and at the latest within 1 business day.
- 4
Invoice included
A tax invoice is attached to the confirmation email. Need a custom invoice? Contact us.
Related Standards
GB/T 9966.17-2021 — Test methods for natural stone—Part 17: Determination of resistance to salt crystallization
GB/T 9966.16-2021 — Test methods for natural stone—Part 16: Determination of linear thermal expansion coefficient
GB/T 9966.15-2021 — Test methods for natural stone—Part 15: Determination of resistance ageing by salt mist
GB/T 9966.18-2021
$85.00