GB/T 9966.17-2021Test methods for natural stone—Part 17: Determination of resistance to salt crystallization (English PDF)
天然石材试验方法 第17部分:盐结晶强度的测定
This is a limited preview
Buy now to download the full PDF (15 pages)
Need quotation for your management?
Get a formal quotation for GB/T 9966.17-2021 in 30 minutes.
Issued by
SAMR; SAC
Level / Type
National · Recommended
Issue date
April 30, 2021
Implementation date
November 1, 2021
Scope
GB/T 9966.17-2021 is the English-translated version of 天然石材试验方法 第17部分:盐结晶强度的测定.
GB/T 9966.17-2021 is the part of the Chinese test methods for natural stone that determines resistance to salt crystallization.
At least six cubes of (40 ± 1) mm side are dried and then taken through 15 cycles, each of 2 hours' immersion in a 14% sodium sulfate decahydrate solution at (20 ± 0.5) °C, drying in an oven at (105 ± 5) °C for (20 ± 2) h and cooling to room temperature, unless the specimen breaks first.
It also covers the apparatus, sample preparation and how to record specimens that break or shatter. The result is the relative mass change of each specimen against its initial dry mass, and the test report lists what to state, including the arithmetic mean. It was issued on 30 April 2021 and has applied since 1 November 2021.
Found what you need?
Document preview — GB/T 9966.17-2021
National Standard of the People's Republic of China
- ICS
- 91.100.15
- Classification
- Q 21
Issued by: State Administration for Market Regulation; Standardization Administration of the PRC
Contents
- Foreword
- 1 Scope
- 3 Principles
- 4 Instruments and Equipment
- 5 Sample Preparation
- 6 Test Procedure
- 7 Test Results
- 8 Test Report
Foreword
GB/T 9966 "Test Methods for Natural Stone" is divided into 18 parts.
---Part 1: Compression strength test after drying, water saturation, and freeze-thaw cycles;
---Part 2: Bending strength test after drying, water saturation, and freeze-thaw cycles;
---Part 3: Water absorption, bulk density, true density, and true porosity tests;
---Part 4: Abrasion Resistance Test;
---Part 5: Hardness Test;
---Part 6: Acid Resistance Test;
---Part 7: Strength test of stone hanging component assembly;
---Part 8: Test method for testing the structural strength of stone cladding systems using uniform static pressure differential;
---Part 9: Determination of dynamic elastic modulus by measuring the fundamental resonant frequency;
---Part 10: Determination of the seismic performance of the hanger assembly unit;
---Part 11: Determination of Accelerated Aging Strength under Rapid Cooling and Heating;
---Part 12: Determination of Static Modulus of Elasticity;
---Part 13: Determination of capillary water absorption coefficient;
---Part 14: Determination of fracture resistance energy;
---Part 15: Determination of Salt Spray Aging Resistance;
---Part 16: Determination of the linear thermal expansion coefficient;
---Part 17: Determination of Salt Crystallization Strength;
---Part 18: Lithofacies Analysis.
This part is Part 17 of GB/T 9966.
This section was drafted in accordance with the rules given in GB/T 1.1-2009.
1 Scope
This part of GB/T 9966 specifies the principle, instruments, equipment, test procedures, and test methods for determining the crystallization strength of natural stone salts. Test results and test reports.
This section applies to the determination of the salt crystallization strength of natural stone.
3 Principles
After drying to constant weight, the sample was immersed in sodium sulfate solution, removed, dried, and then cooled to room temperature. This cycle was repeated 15 times before mass measurement. The percentage change in quantity.
4 Instruments and Equipment
4.1 Forced air drying oven. The temperature can be controlled at (105±5)°C.
4.2 Balance. The measuring range should be no less than 200g, and the measurement accuracy should be no less than 0.01g.
4.3 Laboratory or water bath. capable of maintaining the temperature of the sample and solution at (20±0.5)°C.
4.4 14% sodium sulfate decahydrate solution. i.e., 86g of deionized water mixed with 14g of Na2SO4·10H2O, the solution density at 20°C It is 1.055 kg/m³.
4.5 Desiccant. It shall be a sealed container capable of holding at least one set of test samples and containing a desiccant.
5 Sample Preparation
5.1 Number of Samples
At least six representative samples should be prepared from the same material.
5.2 Sample Specifications
A cube with a side length of (40±1) mm has a surface cut by a diamond circular saw blade. The irregular surface should be polished smooth.
5.3 Cleaning
All loose material on the sample surface must be rinsed with clean water.
5.4 Drying
6 Test Procedure
6.1 The test should use a 14% sodium sulfate decahydrate solution. Before use, the density of the solution should be checked, and the solution should be changed once per cycle.
6.2 Place each dried sample in a 250 mL container, support the bottom with a glass rod, and add sodium sulfate solution so that the distance between the upper surface of the sample and the solution surface is (8±2) mm. Cover the container to reduce evaporation. If dried samples are placed in the same container at the same time, ensure a minimum spacing of 10 mm between samples and a distance of at least 20 mm between the sample and the edge of the container. Immerse the samples in the solution at (20±0.5)°C for 2 hours.
6.3 Before placing the samples, place a pan of water in a cold oven and heat the oven for (30±5) min to maintain relatively high humidity. For a 125L oven, using (300±25) mL of water, a maximum of 48 samples can be dried. Place the soaked samples in the oven to dry, raise the oven temperature to (105±5)°C, and maintain it for (20±2) h.
6.4 After drying the sample in an oven for (20±2) h, cool it to room temperature for (2.0±0.5) h, and then immerse it in a fresh sodium sulfate solution for the next cycle. Repeat the above process 15 times unless the sample breaks. After 15 cycles, remove the sample from the oven and place it in water at (23±5) °C.
6.5 If the specimen breaks or shatters during the test, record the status and the number of cycles completed, and retain images of the initial and final state of the specimen. If the test is interrupted, the specimen should be stored in an oven at (105±5)°C.
7 Test Results
The relative mass change of each sample is calculated according to formula (1), and expressed as a percentage of the mass change (mass loss or increase) to the initial dried mass. […]
8 Test Report
The test report should include at least the following information.
a) The commercial name of the stone as specified in GB/T 17670;
b) Quantity, dimensions, and surface treatment of the samples (as required for testing);
c) Dates of sample delivery, preparation, and measurement;
d) The name and address of the testing laboratory; if the test is not conducted in a testing laboratory, the location of the test should be noted.
e) The standard number followed in the test (GB/T 9966.17-2021);
f) Percentage change in mass for each sample;
g) The arithmetic mean of the test results;
h) Test deviations (such as specimen size and surface treatment).
......
This preview omits tables, figures, formulas and parts of the technical clauses. The complete document — 15 pages — is available in the English PDF.
Similar standards
How to Download GB/T 9966.17-2021
- 1
Add to cart
Click "Download PDF" on this page and choose "Buy this standard". You can add more standards before checkout.
- 2
Checkout
Enter your email and billing details. Payment is processed securely by Stripe (cards or bank transfer). Prefer bank details? Request a quotation (min. order $300).
- 3
Fast delivery
After payment you'll receive an email confirmation. The English PDF is sent to the same address, usually within minutes and at the latest within 1 business day.
- 4
Invoice included
A tax invoice is attached to the confirmation email. Need a custom invoice? Contact us.
Related Standards
GB/T 9966.18-2021 — Test methods for natural stone—Part 18: Petrographic examination
GB/T 9966.16-2021 — Test methods for natural stone—Part 16: Determination of linear thermal expansion coefficient
GB/T 9966.15-2021 — Test methods for natural stone—Part 15: Determination of resistance ageing by salt mist
GB/T 9966.17-2021
$85.00