Valid

GB/T 9966.15-2021Test methods for natural stone—Part 15: Determination of resistance ageing by salt mist (English PDF)

天然石材试验方法 第15部分:耐盐雾老化强度测定

Preview PDF

This is a limited preview

Buy now to download the full PDF (15 pages)

Need quotation for your management?

Get a formal quotation for GB/T 9966.15-2021 in 30 minutes.

Issued by

SAMR; SAC

Level / Type

National · Recommended

Issue date

April 30, 2021

Implementation date

November 1, 2021

Scope

GB/T 9966.15-2021 is the English-translated version of 天然石材试验方法 第15部分:耐盐雾老化强度测定.

GB/T 9966.15-2021 is Part 15 of the Chinese test methods for natural stone and measures how well a stone resists ageing in salt mist. Cube specimens of 50 mm side are exposed in a test chamber to cycles of 4 hours of sodium chloride spray followed by 8 hours of drying at (35 ± 5) °C, for 60 cycles, with a visual inspection every 15 cycles.

The salt is then washed out and the specimens are dried and weighed, so that mass loss and changes in appearance can be assessed. The document specifies the test chamber, spraying device, mist collectors, drying oven, balance, conductivity meter and salt solution, the specimen preparation, the procedure and the test report.

It is used by stone testing laboratories. It was issued on 30 April 2021 and has applied since 1 November 2021.

Found what you need?

Document preview — GB/T 9966.15-2021

National Standard of the People's Republic of China

ICS
91.100.15
Classification
Q 21

Issued by: State Administration for Market Regulation; Standardization Administration of the PRC

Contents

  • Foreword
  • 1 Scope
  • 3 Principles
  • 4 Instruments and Equipment
  • 5 Sample Preparation
  • 6 Experimental Procedure
  • 7 Test Results
  • 8 Test Reports

Foreword

GB/T 9966 "Test Methods for Natural Stone" is divided into 18 parts.

Part 1: Compression strength test after drying, water saturation, and freeze-thaw cycles;

Part 2: Bending strength test after drying, water saturation, and freeze-thaw cycles;

Part 3: Water absorption, bulk density, true density, and true porosity tests;

Part 4: Abrasion Resistance Test;

Part 5: Hardness Test;

Part 6: Acid Resistance Test;

Part 7: Strength Test of Stone Hanging Component Assembly Unit.

Part 8: Test Method for Structural Strength Testing of Stone Hanging Systems Using Uniform Static Pressure Difference;

Part 9: Determination of dynamic elastic modulus by measuring the fundamental resonant frequency;

Part 10: Determination of the seismic performance of the hanger assembly unit;

Part 11: Determination of Accelerated Aging Strength Due to Rapid Cooling and Heating;

Part 12: Determination of Static Modulus of Elasticity;

Part 13: Determination of capillary water absorption coefficient;

Part 14: Determination of fracture resistance energy;

Part 15: Determination of Salt Spray Aging Resistance;

Part 16: Determination of the linear thermal expansion coefficient;

Part 17: Determination of Salt Crystallization Strength

Part 18: Lithofacies Analysis.

This part is Part 15 of GB/T 9966.

This section was drafted in accordance with the rules given in GB/T 1.1-2009.

1 Scope

This part of GB/T 9966 specifies the principle, instruments, equipment, sample preparation, and test procedures for the salt spray aging strength test of natural stone. Steps, test results, and test report.

This section applies to the determination of the salt spray aging resistance of natural stone.

3 Principles

The sample was placed in an aging chamber with atomized salt solution for 4 hours, then dried for 8 hours. This cycle was repeated 60 times to assess the mass loss and appearance changes.

4 Instruments and Equipment

4.1 Test chamber

It can complete the alternating cycle of salt spray and drying (see Figure 1), and the temperature is controlled at (35±5)°C.

4.2 Spraying device

A device for spraying salt solution into the chamber, including atomizing nozzles and deflectors, to avoid direct spraying onto the sample.

4.3 Two atomizing collectors

The horizontal collection area is approximately 8,000 mm² (i.e., a glass funnel with a diameter of 100 mm inserted into a measuring cylinder).

4.4 Forced-air drying oven

Temperature controllable at (65±5)°C.

4.5 Balance

Measuring range not less than 500g, measuring accuracy not less than 0.1g.

4.6 Conductivity meter

Capable of measuring the conductivity of water, selectable for salt solutions and distilled water.

4.7 Sodium chloride solution

Use sodium chloride with a purity of not less than 95% and a distillation solvent with a conductivity of not more than 20 µS/cm at (25±2)°C.

To prepare distilled or deionized water, dissolve (10 ± 1) parts by mass of sodium chloride in 90 parts by mass of distilled or deionized water to obtain a concentration of (100 ± 1) parts by mass of sodium chloride. Prepare a solution of 10 g/L, then filter or pour it out.

4.8 Desiccant

It shall be a sealed container capable of holding at least one set of test samples, with desiccant inside.

5 Sample Preparation

5.1 Number of Samples

Samples should be taken from the same batch of products, and at least 6 samples should be used for testing.

5.2 Sample size

A cube with a side length of (50 ± 1) mm.

5.3 Cleaning

The sample surface should be cleaned with deionized water.

5.4 Dry

Mark the edges of each specimen with a permanent marker to observe the material's degradation status. Place the specimens in a drum at (65 ± 5) °C.

After drying in an air-drying oven for 48 hours, the sample was placed in a desiccator and cooled to room temperature before being weighed. The mass of the dried sample was the initial value m.

6 Experimental Procedure

6.1 Before the test, two salt spray collectors should be placed in the chamber, one closer to the nozzle and the other farther away. Salt spray should be applied for at least 16 hours, followed by a final inspection. Collect 1.0 mL to 2.0 mL of solution per hour using each collector.

6.2 Place the dried sample in the chamber, using non-corrosive supports such as glass or plastic. Each sample should be separated and subjected only to salt spray conditions. Avoid direct spraying or dripping areas.

6.3 After placing the sample under salt spray conditions for 4 h ± 15 min, turn off the salt spray system and allow the sample to dry in the chamber for 8 h ± 15 min, which constitutes one cycle. During the cycle, the temperature inside the chamber should be maintained at (35±5)°C.

6.4 The test requires 60 cycles and may not be terminated prematurely unless at least two samples are observed to have cracked or completely broken by visual inspection.

6.5 Every 15 cycles, remove the sample from the chamber and visually inspect it.

6.6 After the test, gently remove the sample and place it in clean water to remove sediment. The volume of water in the container should be 2 to 3 times the total volume of the sample. Cleaning is a slow process; the water should be changed daily until all salt is completely removed from the sample surface. If the conductivity of the water in contact with the sample does not exceed twice the original value, the salt is considered completely removed.

6.7 After drying the sample in a forced-air drying oven at (65±5)°C for 48 hours, place it in a desiccator to cool to room temperature, weigh it (m), and check its appearance.

7 Test Results

The mass loss of each sample is calculated according to formula (1). […]

8 Test Reports

The test report should include at least the following information.

a) The commercial name of the stone as specified in GB/T 17670;

b) Sample quantity, dimensions, and surface treatment (as required for testing);

c) Dates of sample delivery, preparation, and measurement;

d) The name and address of the testing laboratory; if the test is not conducted in a testing laboratory, the location of the test should be noted.

f) Percentage of appearance change and mass loss for each sample;

g) The arithmetic mean of the mass loss of the test sample;

h) Test deviations (such as sample size, salt spray concentration, and spray volume).

......
This preview omits tables, figures, formulas and parts of the technical clauses. The complete document — 15 pages — is available in the English PDF.

Similar standards

How to Download GB/T 9966.15-2021

  1. 1

    Add to cart

    Click "Download PDF" on this page and choose "Buy this standard". You can add more standards before checkout.

  2. 2

    Checkout

    Enter your email and billing details. Payment is processed securely by Stripe (cards or bank transfer). Prefer bank details? Request a quotation (min. order $300).

  3. 3

    Fast delivery

    After payment you'll receive an email confirmation. The English PDF is sent to the same address, usually within minutes and at the latest within 1 business day.

  4. 4

    Invoice included

    A tax invoice is attached to the confirmation email. Need a custom invoice? Contact us.

Related Standards

English PDF
15 pages
Fast delivery
Invoice included
View Cart

Secure payment via Stripe

Payments accepted

VisaMastercardAmerican ExpressApple PayGoogle PayStripe

GB/T 9966.15-2021

$90.00