Valid

GB/T 9966.14-2021Test methods for natural stone—Part 14: Determination of rupture energy (English PDF)

天然石材试验方法 第14部分:耐断裂能量的测定

Preview PDF

This is a limited preview

Buy now to download the full PDF (15 pages)

Need quotation for your management?

Get a formal quotation for GB/T 9966.14-2021 in 30 minutes.

Issued by

SAMR; SAC

Level / Type

National · Recommended

Issue date

April 30, 2021

Implementation date

November 1, 2021

Scope

GB/T 9966.14-2021 is the English-translated version of 天然石材试验方法 第14部分:耐断裂能量的测定.

GB/T 9966.14-2021 is Part 14 of the Chinese test methods for natural stone and determines the rupture energy of stone by impact. A steel ball of (1.00 ± 0.01) kg is dropped freely onto a dried specimen lying on a sand bed, from a height raised in 50 mm steps until the specimen breaks, and the fracture energy is then calculated.

The standard specifies the apparatus, the drying oven and desiccator, the preparation of specimens for identification tests (200 mm x 200 mm x 30 mm) and for technical tests (actual commercial size), the test procedure, the results and the content of the test report.

It serves material identification as well as product inspection and research testing. It was issued on 30 April 2021 and has applied since 1 November 2021.

Found what you need?

Document preview — GB/T 9966.14-2021

National Standard of the People's Republic of China

ICS
91.100.15
Classification
Q 21

Issued by: State Administration for Market Regulation; Standardization Administration of the PRC

Contents

  • Foreword
  • 1 Scope
  • 3 Principles
  • 4 Instruments and Equipment
  • 5 Sample Preparation
  • 6 Experimental Procedure
  • 7 Test Results
  • 8 Test Reports

Foreword

GB/T 9966 "Test Methods for Natural Stone" consists of 18 parts.

Part 1: Compression strength test after drying, water saturation, and freeze-thaw cycles;

Part 2: Bending strength test after drying, water saturation, and freeze-thaw cycles;

Part 3: Water absorption, bulk density, true density, and true porosity tests; Part 4: Abrasion Resistance Test; Part 5: Hardness Test; Part 6: Acid Resistance Test; Part 7: Strength Test of Stone Hanging Component Assembly Unit.

Part 8: Test Method for Structural Strength Testing of Stone Hanging Systems Using Uniform Static Pressure Difference;

Part 9: Determination of dynamic elastic modulus by measuring the fundamental resonant frequency;

Part 10: Determination of the seismic performance of the hanger assembly unit;

Part 11: Determination of Accelerated Aging Strength Due to Rapid Cooling and Heating; Part 12: Determination of Static Modulus of Elasticity; Part 13: Determination of capillary water absorption coefficient; Part 14: Determination of fracture resistance energy; Part 15: Determination of Salt Spray Aging Resistance; Part 16: Determination of the linear thermal expansion coefficient;

Part 17: Determination of Salt Crystallization Strength Part 18: Lithofacies Analysis. This part is Part 14 of GB/T 9966.

This section was drafted in accordance with the rules given in GB/T 1.1-2009.

1 Scope

This part of GB/T 9966 specifies the principle, equipment, sample preparation, and testing procedures for determining the fracture energy of natural stone by impact. Test procedures, test results, and test reports.

This section applies to the determination of the fracture energy resistance of natural stone. Identification tests are applicable to material identification and inspection, while technical tests are applicable to... Product inspection and research testing.

3 Principles

After the sample is dried to constant weight, it is subjected to impact by a steel ball that is continuously increased in height and then dropped freely until it breaks. The impact fracture energy is then calculated.

4 Instruments and Equipment

4.1 Test Apparatus. The equipment required to determine impact fracture energy includes.

a) A steel ball, with a mass of (1.00±0.01) kg;

b) A container with dimensions not less than 400 mm x 400 mm x 150 mm, containing a layer of silica sand at least 100 mm thick (particle size 2mm~0.076mm), the container should be kept horizontal and its position should be adjustable to ensure the drop point is aligned with the center;

c) A metal column approximately 1.5 m long is connected to the container, with graduations marked at 50 mm intervals;

d) A sliding frame connected to a metal column, which shall have a device for vertically throwing steel balls (using an electromagnetic field-based device). (The system that performs the work), see Figure 1.

4.2 Forced air drying oven. capable of maintaining the temperature at (65±5)°C.

4.3 Desiccant. It shall be a sealed container capable of holding at least one set of actual-sized specimens for qualification and technical testing, with a built-in desiccant.

4.4 Bubble level.

5 Sample Preparation

5.1 Number of samples

Samples should be prepared from the same batch of products. Six samples should be prepared for qualification testing; the number of samples required for technical testing should be determined based on the batch size. The dimensions are determined.

5.2 Sample Requirements

5.2.1 Surface Treatment

The surface of the specimen used for identification testing should be sawed, ground, or polished, while the surface of the specimen used for technical testing should be determined according to the application requirements.

5.2.2 Dimensions

Specimens used for qualification testing should be made to 200 mm x 200 mm x 30 mm, with a tolerance of ±1 mm. Specimen dimensions for technical testing are as follows. This should be the actual size for commercial applications.

5.2.3 Anisotropic Surfaces

For specimens used in identification testing, the decorative surface should be parallel to anisotropic surfaces (such as stratification, foliation, etc.), while for specimens used in technical testing, the decorative surface should be parallel to anisotropic surfaces.

The direction of the anisotropic surface should conform to reality. The direction of the anisotropic surface should be clearly marked on the specimen with two parallel lines.

5.3 Sample Drying

After drying the sample in a forced-air drying oven at 65°C ± 5°C for 48 hours, it was then placed in a desiccator to cool to room temperature.

6 Experimental Procedure

6.1 Select one of the six samples as a reference sample, place it flat on the surface of the sand bed, and align the center of the decorative surface with the vertical line passing through the steel ball.

On a straight line, use a level to check if the top is level.

6.2 The initial drop height of the steel ball is 100 mm, measured from the bottom of the ball. If it does not break at this height, then the drop height is 50 mm.

Adjust the height of the steel ball upwards in one step until the sample breaks, and record the height at which the reference sample breaks (h.).

6.3 Repeat the test on 5 other samples, with an initial height h = (h - 150) mm and a minimum of 100 mm. Record the emission of each sample.

The height (h) of the steel ball at the moment of breakage is accurate to 0.05 m. If a specimen breaks on the first impact, the result should be discarded.

7 Test Results

Calculate the fracture energy of each of the five specimens according to formula (1). […]

8 Test Reports

The test report should include at least the following information.

a) The commercial name of the stone as specified in GB/T 17670;

b) Sample quantity, dimensions, surface treatment (as required for testing), and orientation of anisotropic surfaces;

c) Dates of sample delivery, preparation, and measurement;

d) The name and address of the testing laboratory; if the test is not conducted in a testing laboratory, the location of the test should be noted.

e) The test follows the standard number (GB/T 9966.14-2021);

f) Record the fracture energy of each specimen in joules;

g) Average fracture energy;

h) Test deviations (such as specimen size and surface treatment).

......
This preview omits tables, figures, formulas and parts of the technical clauses. The complete document — 15 pages — is available in the English PDF.

Similar standards

How to Download GB/T 9966.14-2021

  1. 1

    Add to cart

    Click "Download PDF" on this page and choose "Buy this standard". You can add more standards before checkout.

  2. 2

    Checkout

    Enter your email and billing details. Payment is processed securely by Stripe (cards or bank transfer). Prefer bank details? Request a quotation (min. order $300).

  3. 3

    Fast delivery

    After payment you'll receive an email confirmation. The English PDF is sent to the same address, usually within minutes and at the latest within 1 business day.

  4. 4

    Invoice included

    A tax invoice is attached to the confirmation email. Need a custom invoice? Contact us.

Related Standards

English PDF
15 pages
Fast delivery
Invoice included
View Cart

Secure payment via Stripe

Payments accepted

VisaMastercardAmerican ExpressApple PayGoogle PayStripe

GB/T 9966.14-2021

$90.00