GB/T 9556-2008phoxim technical (English PDF)
辛硫磷原药
This is a limited preview
Buy now to download the full PDF (15 pages)
Need quotation for your management?
Get a formal quotation for GB/T 9556-2008 in 30 minutes.
Issued by
SAMR; SAC
Level / Type
National · Recommended
Issue date
July 11, 2008
Implementation date
January 1, 2009
Scope
GB/T 9556-2008 is the English-translated version of 辛硫磷原药.
GB/T 9556-2008 is the Chinese national standard for phoxim technical material, the insecticide of empirical formula C12H15N2O3PS and molecular weight 298.3, a light red oil melting at 5 °C to 6 °C. It fixes the requirements, the test methods and the rules for marking, labelling, packaging, storage and transport, and it applies to the technical material made of phoxim and the impurities produced with it.
The product has to be a pale yellow to reddish brown oily liquid, with a phoxim mass fraction of at least 90.0 %, water no higher than 0.5 % and acidity as H2SO4 no higher than 0.3 %.
Content is measured by reversed-phase liquid chromatography with ultraviolet detection at 254 nm, water by the Karl Fischer method of GB/T 1600. It was issued on 11 July 2008 and has applied since 1 January 2009.
Found what you need?
Document preview — GB/T 9556-2008
National Standard of the People's Republic of China
- ICS
- 65.100.10
- Classification
- G 25
Issued by: State Administration for Market Regulation; Standardization Administration of the PRC
Contents
- Foreword
- 1 Scope
- 2 Normative references
- 3 Requirements
- 4 Test method
Foreword
The standard Chapter 3, Chapter 5 are mandatory, the rest are recommended.
This standard replaces GB 9556-1999 "phoxim the original drug." The main differences between this standard and GB 9556-1999 are as follows.
--- Canceled and classification.
--- Deleted chloride control program.
From the date of implementation of this standard, replace and repeal GB 9556-1999. The standard proposed by China Petroleum and Chemical Industry Association.
1 Scope
This standard specifies requirements for phoxim the original drug, test methods and marking, labeling, packaging, storage and transportation.
This standard applies to the impurities generated by the phoxim its production consisting of phoxim the original drug.
2 Normative references
The following documents contain provisions which, through reference in this standard and become the standard terms. For dated references, subsequent Amendments (not including errata content) or revisions do not apply to this standard, however, encourage the parties to the agreement are based on research Whether the latest versions of these documents. For undated reference documents, the latest versions apply to this standard.
Preparation of GB/T 601 chemical reagent standard titration solution
GB/T 1600 Determination of Water Pesticides
GB/T 1604 Goods pesticide regulations for acceptance
GB/T 1605-2001 Sampling Method commercial pesticides
GB 3796 pesticide packaging General
3 Requirements
3.1 Appearance
Pale yellow to reddish brown oily liquid.
3.2 Technical Specifications
Phoxim the original drug should also meet the requirements of Table 1.
4 Test method
4.1 Sampling
According to GB/T 1605-2001 "on the original drug sampling" approach. Determining sample package using a random number table method, the final sample size should not be Less than 100g.
4.2 Identification Test
HPLC --- The identification test can be carried out simultaneously with the determination of phoxim content. Under the same chromatographic operating conditions, the test A sample solution peak retention time compared with standard sample solution cis phoxim retention time, the relative difference should be less than 1.5%.
4.3 Determination of the mass fraction of phoxim
4.3.1 Method summary
Sample was dissolved in methanol, methanol + water as the mobile phase, to use as filler Capcel-PakC18 stainless steel column and UV detector (254nm), the sample of phoxim reverse phase high performance liquid chromatography, external standard.
4.3.2 Reagents and solutions
Methanol. HPLC grade; Water. The new secondary steam distilled water; Phoxim standard. a known mass fraction >=99.0%.
4.3.3 Instruments
High performance liquid chromatography. a variable wavelength UV detector; Chromatographic data processor;
Column. 150mm × 4.6mm (. I.d) stainless steel column, built Capcel-PakC18,5µm filler (or with equivalent effect Column); Filter. filter pore size of about 0.45µm; Micro injector. 50µL; Quantitative sample line. 5µL; Ultrasonic cleaner.
4.3.4 HPLC operating conditions
Mobile phase. psi (methanol. water) = 75.25, by membrane filtration, and degassing; Flow rate. 1.0mL/min;
Column temperature. room temperature (temperature change should not exceed 2 °C); Detection wavelength. 254nm; Injection volume. 5µL; Retention time. 8.6min.
It said operating parameters are typical, according to the characteristics of different instruments, given operating parameters adjusted as appropriate, in order to obtain the best results.
Typical phoxim the original drug HPLC is shown in Figure 1.
4.3.5 Measuring step
4.3.5.1 Preparation of standard solution
Weigh 0.1g phoxim standard (accurate to 0.0002g), a 50mL volumetric flask, dissolved in methanol and diluted to the mark, shake uniform. Using a pipette to take the above solution 5mL to 50mL volumetric flask, dilute with mobile phase to the mark.
4.3.5.2 Preparation of sample solution
Weigh phoxim containing 0.1g sample (accurate to 0.0002g), a 50mL volumetric flask, dissolved in methanol and diluted to the mark, Shake well. Using a pipette to take the above solution 5mL to 50mL volumetric flask, dilute with mobile phase to the mark.
4.3.5.3 Determination
Under these operating conditions, after the instrument is stable, continuous injection of several doses of the standard solution until the two adjacent needles phoxim peak area relative change After less than 1.5%, according to the solution, sample solution, sample solution, standard order of standard solution was measured.
4.3.6 Calculation
The two needle sample solution and measured before and after the two doses of the standard sample solution phoxim peak areas are averaged. Sample phoxim The mass fraction of 1 (%), according to equation (1). Where. A1 --- the standard solution, the average phoxim peak area; A2 --- sample solution, phoxim mean peak area;
--- Phoxim standard mass fraction, expressed as a percentage.
4.3.7 Allowable difference
Phoxim poor quality score of two parallel determination results shall not be greater than 1.2%, the arithmetic mean value as a measurement result.
4.4 Determination of Moisture
According to GB/T 1600 the "Karl Fischer method".
4.5 Determination of acidity
4.5.1 Reagents and solutions
95% ethanol;
Sodium hydroxide standard titration solution Ba (NaOH) = 0.02mol/L, according to GB/T 601 preparation and calibration;
......
This preview omits tables, figures, formulas and parts of the technical clauses. The complete document — 15 pages — is available in the English PDF.
Referenced standards
Similar standards
How to Download GB/T 9556-2008
- 1
Add to cart
Click "Download PDF" on this page and choose "Buy this standard". You can add more standards before checkout.
- 2
Checkout
Enter your email and billing details. Payment is processed securely by Stripe (cards or bank transfer). Prefer bank details? Request a quotation (min. order $300).
- 3
Fast delivery
After payment you'll receive an email confirmation. The English PDF is sent to the same address, usually within minutes and at the latest within 1 business day.
- 4
Invoice included
A tax invoice is attached to the confirmation email. Need a custom invoice? Contact us.
GB/T 9556-2008
$90.00