GB/T 5584.1-2020Rectangular copper or aluminium and its alloy wires for electrical purposes—Part 1: General (English PDF)
电工用铜、铝及其合金扁线 第1部分：一般规定
This is a limited preview
Buy now to download the full PDF (15 pages)
Need quotation for your management?
Get a formal quotation for GB/T 5584.1-2020 in 30 minutes.
Issued by
SAMR; SAC
Level / Type
National · Recommended
Issue date
December 14, 2020
Implementation date
July 1, 2021
Scope
GB/T 5584.1-2020 is the English-translated version of 电工用铜、铝及其合金扁线 第1部分：一般规定.
GB/T 5584.1-2020 is the Chinese standard "Rectangular copper or aluminium and its alloy wires for electrical purposes—Part 1: General".
Its scope clause reads: This part of GB/T 5584 specifies the terms and definitions, codes and representation methods, cross-sections, materials, dimensions and deviations, mechanical properties, electrical properties, joints, straightness, surface quality, delivery mass, inspection rules, packaging, marking, transportation and storage of rectangular copper or aluminium and its alloy wires and strip copper conductor for electrical purposes.
This part is applicable to the manufacture of windings of motors, electrical appliances and other equipment, the installation of distribution equipment and other rectangular copper or aluminium and its alloy wires and strip copper conductor for electrical purposes. Its clauses include terms and definitions; codes and representation methods.
Found what you need?
Document preview — GB/T 5584.1-2020
National Standard of the People's Republic of China
- ICS
- 29.060.10
- Classification
- K 11
- Replacing
- GB/T 5584.1-2009
Issued by: State Administration for Market Regulation; Standardization Administration of the PRC
Contents
- Foreword i
- 1 Scope
- 2 Normative references
- 3 Terms and definitions
- 4 Codes and representation methods
- 5 Cross-section
- 6 Materials
- 7 Dimension and deviation
- 8 Mechanical properties
- 9 Electrical properties
- 10 Joint
- 11 Straightness
- 12 Surface quality
- 13 Delivery mass
- 14 Inspection rules
- 15 Packaging, marking, transportation and storage
1 Scope
This part of GB/T 5584 specifies the terms and definitions, codes and representation methods, cross-sections, materials, dimensions and deviations, mechanical properties, electrical properties, joints, straightness, surface quality, delivery mass, inspection rules, packaging, marking, transportation and storage of rectangular copper or aluminium and its alloy wires and strip copper conductor for electrical purposes.
This part is applicable to the manufacture of windings of motors, electrical appliances and other equipment, the installation of distribution equipment and other rectangular copper or aluminium and its alloy wires and strip copper conductor for electrical purposes.
2 Normative references
The following referenced documents are indispensable for the application of this document. For dated references, only the edition cited applies. For undated references, the latest edition of the referenced document (including any amendments) applies.
GB/T 321 Preferred numbers—Series of preferred numbers
GB/T 2900.10 Electrotechnical vocabulary—Electric cables
GB/T 3954 Aluminium and aluminium alloys rod for electrical purpose
GB/T 5584.2 Rectangular copper or aluminium and its alloy wires for electrical purposes—Part 2: Rectangular copper and copper alloy wire
GB/T 5584.3 Rectangular copper or aluminium and its alloy wires for electrical purposes—Part 3: Aluminium rectangular wire
GB/T 5584.4 Rectangular copper or aluminium and its alloy wires for electrical purposes—Part 4: Strip copper conductor
JB/T 8137 (all parts) Delivery drums for wires and cables
3 Terms and definitions
For the purposes of this standard, the terms and definitions given in GB/T 2900.10 and the following apply.
3.1 specification
dimension specification of the conductor, which is represented by the nominal size a × b of narrow edge and wide edge
3.2 preferred specification
specification that takes priority over other specifications
3.3 intermediate specification
specification that is allowed but shall not be used as much as possible
3.4 specification not recommended
specification that is not recommended
3.5 straightness
maximum height of the arc when the arc or non-straight part of any narrow edge is horizontal
3.6 proof strength; plastic extension
Rp corresponding stress when the plastic elongation is equal to the specified percentage of extensometer gauge distance L0
Note: The symbol used shall be accompanied by the following footnote to indicate the specified percentage, for example, Rp0.2 refers to the stress when the specified plastic elongation is 0.2%.
[GB/T 228.1-2010, Definition 3.10.3]
4 Codes and representation methods
4.1 Code
Codes include material type code, product type code, cross-sectional shape code and status code, as shown in Table 1.
Table 1 Code
Code classification Code Name
Material type code T Copper
TH11a Class I silver-copper alloy
TH12a Class II silver-copper alloy
TP1b Phosphorized copper
L Aluminum
LH Aluminium alloy
Product type code B Rectangular
D Strip
Cross-sectional shape codec Omitted Fillet
B Round edge
Q Full round edge
Status code R Soft
Yd1/2 Semi hard
Y1 Hard
Y2 Extra hard a Different types of alloys are represented by the first digit after H, and TH1 represents silver-copper alloy; alloys with the same type but different contents are represented by the second digit after H.
b In this part, this material is only used for strip copper conductor.
c In the cross-sectional shape code, the fillet code is omitted.
d This code is only used for copper rectangular wires.
4.2 Designation of the method
4.2.1
The composition and arrangement order of product models are material type code, product type code, cross-sectional shape code and status code.
4.2.2
The product is indicated by model, specification and number of this part.
......
This preview omits tables, figures, formulas and parts of the technical clauses. The complete document — 15 pages — is available in the English PDF.
Similar standards
Editions of GB/T 5584.1
| Edition | Title | Revision | Status |
|---|---|---|---|
| GB/T 5584.1-2020 | Rectangular copper or aluminium and its alloy wires for electrical purposes—Part 1: General | current edition | Current |
| GB/T 5584.1-2009 | Rectangular copper or aluminium and its alloy wires for electrical purposes—Part 1: General | previous edition | Superseded |
This page sells the current edition, GB/T 5584.1-2020. Earlier editions are listed for reference only.
How to Download GB/T 5584.1-2020
- 1
Add to cart
Click "Download PDF" on this page and choose "Buy this standard". You can add more standards before checkout.
- 2
Checkout
Enter your email and billing details. Payment is processed securely by Stripe (cards or bank transfer). Prefer bank details? Request a quotation (min. order $300).
- 3
Instant delivery (0–9 sec)
Delivery is automatic: within seconds of payment you'll receive an email with a secure download link. The link stays valid for 72 hours.
- 4
Invoice included
A tax invoice is attached to the confirmation email. Need a custom invoice? Contact us.
Related Standards
GB/T 5584.2-2020 — Rectangular copper or aluminium and its alloy wires for electrical purposes - Part 2: Rectangular copper and copper alloy wire
GB/T 5584.3-2009 — Rectangular copper or aluminium and its alloy wires for electrical purposes - Part 3: Aluminium rectanglar wire
GB/T 5584.4-2020 — Rectangular copper or aluminium and its alloy wires for electrical purposes - Part 4: Strip copper conductor
Secure payment via Stripe
Payments accepted
GB/T 5584.1-2020
$185.00