GB/T 4372.3-2015Methods for chemical analysis of zincoxide produced by direct process - Part 3: Determination of copper oxide content - Flame atomic absorption spectrometry method (English PDF)
直接法氧化锌化学分析方法 第3部分：氧化铜量的测定 火焰原子吸收光谱法
This is a limited preview
Buy now to download the full PDF (15 pages)
Need quotation for your management?
Get a formal quotation for GB/T 4372.3-2015 in 30 minutes.
Issued by
SAMR; SAC
Level / Type
National · Recommended
Issue date
September 11, 2015
Implementation date
April 1, 2016
Scope
GB/T 4372.3-2015 is the English-translated version of 直接法氧化锌化学分析方法 第3部分：氧化铜量的测定 火焰原子吸收光谱法.
GB/T 4372.3-2015 is the Chinese standard "Methods for chemical analysis of zincoxide produced by direct process - Part 3: Determination of copper oxide content - Flame atomic absorption spectrometry method".
Its scope clause reads: This part of GB/T 4372 specifies the method for the determination of the amount of copper oxide in direct zinc oxide. This part is applicable to the determination of the amount of copper oxide in direct zinc oxide.
Determination range. copper oxide. 0.0005% ~ 0.020%. Its clauses include method summary; reagent; instruments; samples.
Found what you need?
Document preview — GB/T 4372.3-2015
National Standard of the People's Republic of China
- ICS
- 77.120.60
- Classification
- H 13
- Replacing
- GB/T 4372.3-2001
Issued by: State Administration for Market Regulation; Standardization Administration of the PRC
Contents
- 1 Scope
- 2 method summary
- 3 reagent
- 4 instruments
- 5 samples
1 Scope
This part of GB/T 4372 specifies the method for the determination of the amount of copper oxide in direct zinc oxide.
This part is applicable to the determination of the amount of copper oxide in direct zinc oxide. Determination range. copper oxide. 0.0005% ~ 0.020%.
2 method summary
The sample was dissolved in nitric acid and used in a dilute nitric acid medium using an air-acetylene flame at an atomic absorption spectrometer wavelength of 324.8 nm
Copper absorbance, the standard curve method to calculate the amount of copper oxide, cadmium oxide.
3 reagent
Unless otherwise stated, only the reagents identified as analytical reagents and distilled or deionized water or comparable purity were used in the analysis.
3.1
nitric acid (rho = 1.42 g/mL).
3.2
nitric acid (1 1).
3.3 copper standard storage solution
Weigh 0.1000g pure copper (wCu >= 99.99%) in 300mL beaker, add 10mL nitric acid (3.1),
Dissolved in low temperature heating, boil nitrogen removal of the oxide, cooling, into the 1000mL volumetric flask, add 40mL nitric acid (3.1), diluted with water
To the scale, mix. This solution contains 1 g of 100 g of copper.
3.4 Copper standard solution
Remove 10.00mL copper standard storage solution (3.3) In a 100mL volumetric flask, add 5mL nitric acid (3.1), add
Water diluted to the mark, mix well. 1 mL of this solution contains 10 g of copper.
4 instruments
Atomic Absorption Spectrometer, Copper Hollow Cathode Lamp.
In the best working conditions of the instrument, who can meet the following indicators can be used.
Sensitivity. The concentration of copper in the solution consistent with the measurement sample solution matrix should not be greater than 0.035 µg/mL.
Precision. the highest concentration of the standard solution measured 10 times the absorbance, the standard deviation should not exceed 1.0% of the average absorbance; with the most
Low standard solution (not zero standard solution) measured 10 times the absorbance, the standard deviation does not exceed the maximum concentration of standard solution average absorbance
0.5% of the degree.
The linearity of the working curve. the ratio of the difference between the absorbance difference and the absorbance difference of the lowest section is divided into five segments according to the concentration,
Should not be less than 0.7.
5 samples
5.1
Specimen size should be less than 0.10mm.
......
This preview omits tables, figures, formulas and parts of the technical clauses. The complete document — 15 pages — is available in the English PDF.
Similar standards
Editions of GB/T 4372.3
| Edition | Title | Revision | Status |
|---|---|---|---|
| GB/T 4372.3-2015 | Methods for chemical analysis of zincoxide produced by direct process - Part 3: Determination of copper oxide content - Flame atomic absorption spectrometry method | current edition | Current |
| GB/T 4372.3-2001 | Methods for chemical analysis of zincoxide produced by direct process - Part 3: Determination of copper oxide content - Flame atomic absorption spectrometry method | previous edition | Superseded |
This page sells the current edition, GB/T 4372.3-2015. Earlier editions are listed for reference only.
How to Download GB/T 4372.3-2015
- 1
Add to cart
Click "Download PDF" on this page and choose "Buy this standard". You can add more standards before checkout.
- 2
Checkout
Enter your email and billing details. Payment is processed securely by Stripe (cards or bank transfer). Prefer bank details? Request a quotation (min. order $300).
- 3
Instant delivery (0–9 sec)
Delivery is automatic: within seconds of payment you'll receive an email with a secure download link. The link stays valid for 72 hours.
- 4
Invoice included
A tax invoice is attached to the confirmation email. Need a custom invoice? Contact us.
Related Standards
GB/T 4372.4-2015 — Methods for chemical analysis of zincoxide produced by direct process - Part 4: Determination of cadmium oxide content - Flame atomic absorption spectrometry method
GB/T 4372.2-2001 — Methods for chemical analysis of zinc oxide produced by direct process - Determination of lead oxide content - Atomic absorption spectrometry method
GB/T 4372.4-2001 — Methods for chemical analysis of zinc oxide produced by direct process - Determination of cadmium oxide content - Atomic absorption spectrometry method
Secure payment via Stripe
Payments accepted
GB/T 4372.3-2015
$65.00