Valid

GB/T 43061-2023Semiconductor integrated circuits—Test methods of PWM controller (English PDF)

半导体集成电路 PWM控制器测试方法

Preview PDF

This is a limited preview

Buy now to download the full PDF (46 pages)

Need quotation for your management?

Get a formal quotation for GB/T 43061-2023 in 30 minutes.

Issued by

SAMR; SAC

Level / Type

National · Recommended

Issue date

September 7, 2023

Implementation date

April 1, 2024

Scope

GB/T 43061-2023 is the English-translated version of 半导体集成电路 PWM控制器测试方法.

This document describes the methods for testing the parameters of the pulse width modulation controllers made as semiconductor integrated circuits. The document applies to the parameter testing of PWM controllers in semiconductor integrated circuits.

Found what you need?

Document preview — GB/T 43061-2023

National Standard of the People's Republic of China

ICS
31.200
Classification
L 55

Issued by: State Administration for Market Regulation; Standardization Administration of the PRC

Contents

  • Preface
  • 1 Scope
  • 2 Normative reference documents
  • 3 Terms and Definitions
  • 4 General test requirements
  • 4.1 Test environment requirements
  • 4.2 Test Notes
  • 4.3 Test instruments and equipment
  • 5 Test conditions and test procedures
  • 5.1 Reference source unit
  • 5.1.1 Reference voltage (VREF)
  • 5.1.2 Voltage adjustment variation (SV)
  • 5.1.3 Current adjustment variation (SI)
  • 5.1.4 Reference voltage temperature coefficient (ST)
  • 5.1.5 Overall variation range of output voltage (VTOT)
  • 5.1.6 Output noise voltage (VNO)
  • 5.1.7 Output short-circuit current (IOS)
  • 5.2 Oscillator unit
  • 5.2.1 Initial frequency (fI)
  • 5.2.2 Voltage stability (fV)
  • 5.2.3 Temperature stability (fT)
  • 5.2.4 Overall frequency variation range (fTOT)
  • 5.2.5 Minimum operating frequency (fmin)
  • 5.2.6 Maximum operating frequency (fmax)
  • 5.2.7 Output pulse high-level voltage [VOH(osc)]
  • 5.2.8 Output pulse low-level voltage [VOL(osc)]
  • 5.2.9 Output pulse voltage amplitude [VOA(osc)]
  • 5.2.10 Output pulse width (tW)
  • 5.2.11 Ramp peak voltage [VP(ramp)]
  • 5.2.12 Sawtooth valley voltage [VV(ramp)]
  • 5.2.13 Sawtooth valley-peak voltage amplitude [VA(ramp)]
  • 5.2.14 Synchronous terminal input current [II(sync)]
  • 5.2.15 Synchronization threshold voltage [VTH(sync)]
  • 5.3 Error amplifier unit
  • 5.3.1 Input offset voltage (VIO)
  • 5.3.2 Input bias voltage (VIB)
  • 5.3.3 Input offset current (IIO)
  • 5.3.4 Input bias current (IIB)
  • 5.3.5 Open loop voltage gain (AVD)
  • 5.3.6 Common mode rejection ratio (KCMR)
  • 5.3.7 Supply voltage rejection ratio (KSVR)
  • 5.3.8 Common mode input voltage range (VICM)
  • 5.3.9 Output voltage slew rate (SR)
  • 5.3.10 Unity gain bandwidth (fBWG)
  • 5.3.11 Output current (ISO URCE)
  • 5.3.12 Input current (ISINK)
  • 5.3.13 Output high-level voltage (VOH)
  • 5.3.14 Output low-level voltage (VOL)
  • 5.4 PWM Comparator Unit
  • 5.4.1 Duty cycle adjustment range (q)
  • 5.4.2 Zero duty cycle threshold voltage [VTH(zq)]
  • 5.4.3 Maximum duty cycle threshold voltage [VTH(mq)]
  • 5.4.4 Output delay time [tdr(pwm)/tdf(pwm)]
  • 5.5 Output drive unit
  • 5.5.1 Output low-level voltage [VOL(drv)]
  • 5.5.2 Output high-level voltage [VOH(drv)]
  • 5.5.3 Output rise/fall time (tr/tf)
  • 5.5.4 Output leakage current [IO(off)]
  • 5.6 Soft start unit
  • 5.6.1 Charging current (ICHG)
  • 5.6.2 Discharge current (IDCG)
  • 5.7 Current limiting protection/shutdown unit
  • 5.7.1 Turn-off threshold voltage [VTH(sd)]
  • 5.7.2 Shutdown-output delay time [td(sd)]
  • 5.8 Undervoltage lockout unit
  • 5.8.1 Start-up voltage [VCC(st)]
  • 5.8.2 Minimum operating voltage [VCC(min)]
  • 5.8.3 Hysteresis voltage (deltaVCC)
  • 5.9 Power consumption
  • 5.9.1 Starting supply current [ICC(st)]
  • 5.9.2 Supply current (ICC)

Foreword

This document complies with the provisions of GB/T 1.1-2020 "Standardization Work Guidelines Part 1: Structure and Drafting Rules of Standardization Documents" Drafting.

1 Scope

This document describes the parameter testing methods for semiconductor integrated circuit pulse width modulation (PWM) controllers (hereinafter referred to as devices).

This document is suitable for testing PWM controller parameters in the field of semiconductor integrated circuits.

2 Normative reference documents

The contents of the following documents constitute essential provisions of this document through normative references in the text. Among them, the dated quotations For undated referenced documents, only the version corresponding to that date applies to this document; for undated referenced documents, the latest version (including all amendments) applies to this document.

GB/T 17940-2000 Semiconductor device integrated circuits Part 3: Analog integrated circuits

3 Terms and definitions

The following terms and definitions apply to this document.

3.1 Reference source unit

3.1.1 Referencevoltage

The output voltage of the reference source under the specified supply voltage and load current.

3.1.2 Voltage regulation variation voltageregulation Under the specified load current, the reference source output voltage changes with the power supply voltage.

3.1.3 Current regulation variation currentregulation Under the specified power supply voltage, the variation of the reference source output voltage with the load current.

3.1.4 The rate of change of the reference voltage with ambient temperature

3.1.5 Under specified operating conditions, the overall variation range of the reference source output voltage with temperature, supply voltage and load current.

3.1.6 Output noise voltage

The output noise voltage generated internally by the reference.

3.1.7 Under the specified power supply voltage, the current when the reference source output is short-circuited to ground.

......
This preview omits tables, figures, formulas and parts of the technical clauses. The complete document — 46 pages — is available in the English PDF.

Referenced standards

Similar standards

How to Download GB/T 43061-2023

  1. 1

    Add to cart

    Click "Download PDF" on this page and choose "Buy this standard". You can add more standards before checkout.

  2. 2

    Checkout

    Enter your email and billing details. Payment is processed securely by Stripe (cards or bank transfer). Prefer bank details? Request a quotation (min. order $300).

  3. 3

    Fast delivery

    After payment you'll receive an email confirmation. The English PDF is sent to the same address, usually within minutes and at the latest within 1 business day.

  4. 4

    Invoice included

    A tax invoice is attached to the confirmation email. Need a custom invoice? Contact us.

Related Standards

English PDF
46 pages
Fast delivery
Invoice included
View Cart

Secure payment via Stripe

Payments accepted

VisaMastercardAmerican ExpressApple PayGoogle PayStripe

GB/T 43061-2023

$900.00