Valid

GB/T 40926.1-2021Protective equipment for use in ice hockey - Part 1: General requirements (English PDF)

冰球运动护具 第1部分:通用要求

Preview PDF

This is a limited preview

Buy now to download the full PDF (17 pages)

Need quotation for your management?

Get a formal quotation for GB/T 40926.1-2021 in 30 minutes.

Issued by

State Administration for Market Regulation, China National Standardization Administration

Level / Type

National · Recommended

Issue date

November 26, 2021

Implementation date

November 26, 2021

Scope

GB/T 40926.1-2021 is the English-translated version of 冰球运动护具 第1部分:通用要求.

GB/T 40926.1-2021 is the Chinese standard "Protective equipment for use in ice hockey - Part 1: General requirements". Its scope clause reads: This document specifies general requirements for head, face, neck and body protective gear (hereinafter referred to as protective gear) for ice hockey.

This document applies to protective gear for ice hockey, and the requirements are as follows. a) Terms and definitions; b) Harmlessness; c) Ergonomics; d) Test report; e) Permanent identification; f) Product information.

The other parts of this document specify the performance requirements of ice hockey protective gear and are used in conjunction with this document. Note 1.The requirements of the clause take precedence over the graphics.

Note 2.The purpose of this document is to reduce the risk of injury to players without compromising the competitive state and appeal of ice hockey. Its clauses include terms and definitions.

Found what you need?

Document preview — GB/T 40926.1-2021

National Standard of the People's Republic of China

Classification
Y 55

Issued by: State Administration for Market Regulation, China National Standardization Administration

Contents

  • Foreword
  • Introduction
  • 1 Scope
  • 2 Normative references
  • 3 Terms and definitions
  • 4 Requirements
  • 4.1 Harmlessness
  • 4.2 Ergonomics
  • 5 Test method
  • 5.1 Harmlessness determination
  • 5.2 Ergonomic measurement
  • 6 Dimensional deviation
  • 7 Sample pre-treatment conditions
  • 7.1 Normal temperature state adjustment
  • 7.2 Low temperature state adjustment
  • 7.3 High temperature state adjustment
  • 8 Test report
  • 9 Permanent identification
  • 10 Provide user information

1 Scope

This document specifies general requirements for head, face, neck and body protective gear (hereinafter referred to as protective gear) for ice hockey.

This document applies to protective gear for ice hockey, and the requirements are as follows.

a) Terms and definitions;

b) Harmlessness;

c) Ergonomics;

d) Test report;

e) Permanent identification;

f) Product information.

The other parts of this document specify the performance requirements of ice hockey protective gear and are used in conjunction with this document.

Note 1.The requirements of the clause take precedence over the graphics.

Note 2.The purpose of this document is to reduce the risk of injury to players without compromising the competitive state and appeal of ice hockey.

2 Normative references

There are no normative references in this document.

3 Terms and definitions

The following terms and definitions apply to this document.

3.1 Permanentmarking

Can not be removed under normal use conditions and maintain clear information.

3.2 Basicplaneoftheheadform

Relative to the plane of the head model, it corresponds to the reference plane of the human head (3.3).

Note. See Figure 1.

3.3 Basicplaneofthehumanhead

Located on the plane of the upper edge of the outer side of the ear canal (external auditory mouth) and the lower edge of the eye socket.

3.4 Horizontalplane

A plane passing through the body perpendicular to the front plane and the longitudinal midplane (3.5).

Note. See Figure 1.

3.5 Medianplane

Pass the head mold from front to back to divide the head mold into two symmetrical vertical planes. […]

......
This preview omits tables, figures, formulas and parts of the technical clauses. The complete document — 17 pages — is available in the English PDF.

Referenced standards

How to Download GB/T 40926.1-2021

  1. 1

    Add to cart

    Click "Download PDF" on this page and choose "Buy this standard". You can add more standards before checkout.

  2. 2

    Checkout

    Enter your email and billing details. Payment is processed securely by Stripe (cards or bank transfer). Prefer bank details? Request a quotation (min. order $300).

  3. 3

    Fast delivery

    After payment you'll receive an email confirmation. The English PDF is sent to the same address, usually within minutes and at the latest within 1 business day.

  4. 4

    Invoice included

    A tax invoice is attached to the confirmation email. Need a custom invoice? Contact us.

Related Standards

English PDF
17 pages
Fast delivery
Invoice included
View Cart

Secure payment via Stripe

Payments accepted

VisaMastercardAmerican ExpressApple PayGoogle PayStripe

GB/T 40926.1-2021

$150.00