GB/T 40926.5-2021Protective equipment for use in ice hockey - Part 5: Neck laceration protectors for ice hockey players (English PDF)
冰球运动护具 第5部分:颈部护具
This is a limited preview
Buy now to download the full PDF (37 pages)
Need quotation for your management?
Get a formal quotation for GB/T 40926.5-2021 in 30 minutes.
Issued by
State Administration for Market Regulation, China National Standardization Administration
Level / Type
National · Recommended
Issue date
November 26, 2021
Implementation date
November 26, 2021
Scope
GB/T 40926.5-2021 is the English-translated version of 冰球运动护具 第5部分:颈部护具.
GB/T 40926.5-2021 is the Chinese standard "Protective equipment for use in ice hockey - Part 5: Neck laceration protectors for ice hockey players". Its scope clause reads: This document specifies the performance requirements and test methods for neck protectors in ice hockey.
Neck protectors are used to reduce contact with hockey pucks, The injury caused by the direct cut of the neck by the blade of the ice skate shoe. The test requirements ensure that the neck protector meets the requirements of this document, but it cannot predict the performance of the neck protector under all possible conditions. can.
This document does not deal with the impact of hockey pucks, hockey sticks or other objects on the neck. This document does not cover accessories related to neck protectors. Its clauses include terms and definitions.
Found what you need?
Document preview — GB/T 40926.5-2021
National Standard of the People's Republic of China
- Classification
- Y 55
Issued by: State Administration for Market Regulation, China National Standardization Administration
Contents
- Foreword
- Introduction
- 1 Scope
- 2 Normative references
- 3 Terms and definitions
- 4 General requirements
- 4.1 Harmlessness/material
- 4.2 Ergonomics
- 4.3 Protection area and coverage area
- 4.4 Anti-cutting
- 4.5 Permanent Mark
- 5 Test method
- 5.1 Test device deviation
- 5.2 Test samples and pre-test treatment
- 5.3 Test Step
- 6 Test report
- 7 Marking and labeling
- 7.1 Identification
- 7.2 Label
- 8 Product information
- Appendix A (Normative) Cutting test using a horizontal single rail device
- Appendix B (Normative) Cutting test using guided drop device
- Appendix C (Normative) Structural Model
1 Scope
This document specifies the performance requirements and test methods for neck protectors in ice hockey. Neck protectors are used to reduce contact with hockey pucks,
The injury caused by the direct cut of the neck by the blade of the ice skate shoe.
The test requirements ensure that the neck protector meets the requirements of this document, but it cannot predict the performance of the neck protector under all possible conditions.
can. This document does not deal with the impact of hockey pucks, hockey sticks or other objects on the neck.
This document does not cover accessories related to neck protectors.
2 Normative references
The content of the following documents constitutes an indispensable clause of this document through normative references in the text. Among them, dated quotations
Only the version corresponding to the date is applicable to this document; for undated reference documents, the latest version (including all amendments) is applicable to
This document.
GB/T 40926.1-2021 Ice hockey protective gear Part 1.General requirements (ISO 10256-1.2016, IDT)
ISO 6330 Textiles-Domestic washing and drying procedure (Textiles-Domestic washing and drying procedure- duresfortextiletesting)
Note. GB/T 8629-2017 Domestic washing and drying procedures for textile testing (ISO 6330.2012, MOD)
3 Terms and definitions
The following terms and definitions defined in GB/T 40926.1-2021 apply to this document.
3.1 Structural model anatomicalform
A solid or hollow object defined by its shape and size, used to support the neck protector (3.6) meets the test requirements of this document.
3.2 Anvil
A hard metal block with a round or square cross-section, with a prescribed shape at the upper end, is used to transmit the impact force of the sample to the force sensor.
3.3 Bib
Part of the neck protector (3.6), located above the front chest area.
3.4 Medianplane
Pass through the neck protector (3.6) from front to back and divide the neck protector into two equal vertical planes on the left and right.
3.5 Model
The category of neck protectors (3.6) is different from the basic elements.
GB/T 41526.1 | GB/T 20394 | GB 24429 | GB/T 40926.4 | GB/T 40926.3 | GB/T 40926.2 | […]
......
This preview omits tables, figures, formulas and parts of the technical clauses. The complete document — 37 pages — is available in the English PDF.
Referenced standards
Normative references
- GB/T 40926.1-2021Protective equipment for use in ice hockey - Part 1: General requirements
- GB/T 8629-2017Textiles -- Domestic washing and drying procedures for textile testing
ISO 10256 · ISO 6330 · ISO 6330.2012
How to Download GB/T 40926.5-2021
- 1
Add to cart
Click "Download PDF" on this page and choose "Buy this standard". You can add more standards before checkout.
- 2
Checkout
Enter your email and billing details. Payment is processed securely by Stripe (cards or bank transfer). Prefer bank details? Request a quotation (min. order $300).
- 3
Fast delivery
After payment you'll receive an email confirmation. The English PDF is sent to the same address, usually within minutes and at the latest within 1 business day.
- 4
Invoice included
A tax invoice is attached to the confirmation email. Need a custom invoice? Contact us.
Related Standards
GB/T 40926.1-2021 — Protective equipment for use in ice hockey - Part 1: General requirements
GB/T 8629-2017 — Textiles -- Domestic washing and drying procedures for textile testing
GB/T 40926.4-2021 — Protective equipment for use in ice hockey - Part 4: Head and face protection for goalkeepers
GB/T 40926.5-2021
$330.00