Valid

GB/T 40698-2021General requirements for aerospace control system engineering (English PDF)

航天控制系统工程通用要求

Preview PDF

This is a limited preview

Buy now to download the full PDF (17 pages)

Need quotation for your management?

Get a formal quotation for GB/T 40698-2021 in 30 minutes.

Issued by

SAMR; SAC

Level / Type

National · Recommended

Issue date

October 11, 2021

Implementation date

May 1, 2022

Scope

GB/T 40698-2021 is the English-translated version of 航天控制系统工程通用要求.

GB/T 40698-2021 sets out the general requirements for engineering the control systems of spacecraft and launch vehicles.

It covers the whole range of technical activities in control system engineering - requirements definition, analysis, design, production, verification and validation, operation, maintenance and disposal - together with the process requirements that go with them.

The document defines its key terms, among them control component, controller, sensor and actuator, and draws on national standards for system and software life cycle processes, verification and validation, space control system simulation, aerospace project management and space debris mitigation.

It is intended for those who design, produce, verify and use spacecraft and launch vehicle control systems. It was issued on 11 October 2021 and has applied since 1 May 2022.

Found what you need?

Document preview — GB/T 40698-2021

National Standard of the People's Republic of China

ICS: 49.020
Classification: V 73

Issued by: State Administration for Market Regulation; Standardization Administration of the PRC

Foreword
1 Scope
2 Normative references
3 Terms and definitions

Foreword

This document is in accordance with the provisions of GB/T 1.1-2020 "Guidelines for Standardization Work Part 1: Structure and Drafting Rules of Standardization Documents" Drafting.

1 Scope

This document specifies the aerospace control system engineering technical activities (requirements definition, analysis, design, production, verification and validation, operation, maintenance and Disposal) general requirements and process requirements.

This document applies to the design, production, verification and use of spacecraft and launch vehicle control systems.

2 Normative references

The content of the following documents constitutes an indispensable clause of this document through normative references in the text. Among them, dated quotations Only the version corresponding to the date is applicable to this document; for undated reference documents, the latest version (including all amendments) is applicable to this document.

GB/T 8566 Information Technology Software Life Cycle Process

GB/T 9414.9 Maintainability Part 9: Maintenance and Maintenance Support

GB/T 22032 System Engineering System Life Cycle Process

GB/T 32295 Design Requirements for Surplus Propellant Emissions of Launch Vehicles

GB/T 32297 Space Control System Simulation Requirements

GB/T 32423 System and Software Engineering Verification and Confirmation

GB/T 32451 Aerospace Project Management

GB/T 34513 Space debris mitigation requirements

GB/T 38194 Operational Debris Mitigation Design Requirements for Launch Vehicles

3 Terms and definitions

The following terms and definitions apply to this document.

3.1 Control component

In order to achieve the control goal, a part or all of the components used in the control system.

3.2 Controller

A control component that enables the controlled object to have specific control performance.

3.3 Sensor

A device that measures the state of the controlled object and inputs it to the controller.

3.4 Actuator

According to the instructions of the controller, the components that control the required force or torque are produced.

......
This preview omits tables, figures, formulas and parts of the technical clauses. The complete document — 17 pages — is available in the English PDF.

Referenced standards

Normative references

Similar standards

GB/T 29072-2026|GB/T 29073-2026|GB/T 29078-2026|GB/T 29082-2026|GB/T 29084-2026|GB/T 29085-2026

How to Download GB/T 40698-2021

1
Add to cart
Click "Download PDF" on this page and choose "Buy this standard". You can add more standards before checkout.
2
Checkout
Enter your email and billing details. Payment is processed securely by Stripe (cards or bank transfer). Prefer bank details? Request a quotation (min. order $300).
3
Instant delivery (0–9 sec)
Delivery is automatic: within seconds of payment you'll receive an email with a secure download link. The link stays valid for 72 hours.
4
Invoice included
A tax invoice is attached to the confirmation email. Need a custom invoice? Contact us.