GB/T 40007-2021Nanotechnology—Contacting methods for measuring the resistivity of nanomaterials—General rules (English PDF)
纳米技术 纳米材料电阻率的接触式测量方法 通则
This is a limited preview
Buy now to download the full PDF (19 pages)
Need quotation for your management?
Get a formal quotation for GB/T 40007-2021 in 30 minutes.
Issued by
SAMR; SAC
Level / Type
National · Recommended
Issue date
May 21, 2021
Implementation date
December 1, 2021
Scope
GB/T 40007-2021 is the English-translated version of 纳米技术 纳米材料电阻率的接触式测量方法 通则.
GB/T 40007-2021 sets general rules for measuring the resistivity of nanomaterials by contact methods.
It describes three methods: the static four-probe method (method A) for nano-films, nano-pastes and nano-powders, and the dynamic four-probe method (method B) and dynamic four-wire two-electrode method (method C) for nano-powders, which are measured under continuous pressure at different compaction densities.
The standard covers the principle of each method, general and special equipment, measurement conditions, sample preparation for films, pastes and powders, method selection and measurement procedures.
It also discusses how water content, applied pressure and humidity influence the result and what the measurement report must contain, with measurement examples for each method in informative annexes.
Laboratories measuring nanomaterials use it. It was issued on 21 May 2021 and has applied since 1 December 2021.
Found what you need?
Document preview — GB/T 40007-2021
National Standard of the People's Republic of China
- ICS
- 17.220.20
- Classification
- H 21
Issued by: State Administration for Market Regulation; Standardization Administration of the PRC
Contents
- Foreword
- 1 Scope
- 2 Normative references
- 3 Terms and definitions
- 4 Principle
- 4.1 Static four-probe method (A method)
- 4.2 Dynamic four-probe method (Method B)
- 4.3 Dynamic four-wire two-electrode method (C method)
- 5 Equipment
- 5.1 General equipment
- 5.2 Special equipment
- 6 Measurement conditions
- 7 Sample preparation
- 7.1 Film
- 7.2 Slurry
- 7.3 Powder
- 7.4 Measurement of diaphragm size
- 8 Sample measurement
- 8.1 Method selection
- 8.2 Method A
- 8.3 Method B
- 8.4 Method C
- 9 Influencing factors
- 9.1 The influence of water content on the conductivity measurement method
- 9.2 The influence of applied pressure on the conductivity measurement method
- 9.3 The influence of humidity on the conductivity measurement method
- 10 Measurement report
- Appendix A (informative appendix) Method A measurement example
- Appendix B (informative appendix) B method measurement example
- Appendix C (informative appendix) C method measurement example Reference
Foreword
This standard was drafted in accordance with the rules given in GB/T 1.1-2009.
1 Scope
This standard specifies the contact measurement method for the resistivity of nanomaterials, including measurement principles, instruments and equipment, measurement conditions, measurement procedures, Influencing factors, etc.
The static four-probe method (Method A) in this standard is suitable for resistivity measurement of nano-film, nano-paste and nano-powder; dynamic four-probe Method (B method) and dynamic four-wire two-electrode method (C method) are suitable for the measurement of resistivity of nano powders.
2 Normative references
The following documents are indispensable for the application of this document. For dated reference documents, only the dated version applies to this document. For undated reference documents, the latest version (including all amendments) is applicable to this document.
GB/T 32269 Terms and definitions of nanotechnology and nanoobjects Nanoparticles, nanofibers and nanosheets
3 Terms and definitions
The following terms and definitions defined in GB/T 32269 apply to this document.
3.1 Nanomaterial
Any material whose external dimension, internal or surface structure is at the nanometer scale. [GB/T 30544.1-2014, definition 2.4]
3.2 Resistivity
The ratio of the current electric field intensity inside the material to the steady-state current density is the volume resistance per unit volume.
3.3 Static four-probe method
Nano-powder material is pre-pressed and molded, and the four-probe resistivity measuring instrument is used to measure the molded sample. Because there is no continuous pressure, the molding is to be tested The compacted density of the sample remains static, and the method of measuring the resistivity under the compacted density.
3.4 Dynamic four probe method
The nano powder material does not need to be pre-compressed. During the measurement process with a four-probe resistivity measuring instrument, the sample to be tested is compacted due to continuous pressure.
The method of measuring the resistivity of the sample to be tested under different compaction densities.
......
This preview omits tables, figures, formulas and parts of the technical clauses. The complete document — 19 pages — is available in the English PDF.
Referenced standards
Similar standards
How to Download GB/T 40007-2021
- 1
Add to cart
Click "Download PDF" on this page and choose "Buy this standard". You can add more standards before checkout.
- 2
Checkout
Enter your email and billing details. Payment is processed securely by Stripe (cards or bank transfer). Prefer bank details? Request a quotation (min. order $300).
- 3
Fast delivery
After payment you'll receive an email confirmation. The English PDF is sent to the same address, usually within minutes and at the latest within 1 business day.
- 4
Invoice included
A tax invoice is attached to the confirmation email. Need a custom invoice? Contact us.
Related Standards
GB/T 32269-2015 — Nanotechnologies -- Terminology and definitions for nano-objects -- Nanoparticle, nano-fibre and nanoplate
GB/T 10003-2026 — Biaxially oriented polypropylene (BOPP) film
GB/T 10004-2026 — Plastic/Plastic laminated films and pouches for packaging
GB/T 40007-2021
$300.00