GB/T 39709-2020Test methods of multiple units glass, windiows static pressure and windiows sealing performance (English PDF)
动车组玻璃、车窗耐静压及车窗密封性能试验方法
This is a limited preview
Buy now to download the full PDF (15 pages)
Need quotation for your management?
Get a formal quotation for GB/T 39709-2020 in 30 minutes.
Issued by
SAMR; SAC
Level / Type
National · Recommended
Issue date
December 14, 2020
Implementation date
November 1, 2021
Scope
GB/T 39709-2020 is the English-translated version of 动车组玻璃、车窗耐静压及车窗密封性能试验方法.
GB/T 39709-2020 is the Chinese standard "Test methods of multiple units glass, windiows static pressure and windiows sealing performance".
Its scope clause reads: This standard specifies the test conditions, basic principles, test equipment, test equipment, Test samples, test procedures and test reports: This standard is applicable to the evaluation of static pressure resistance and sealing performance of EMU glass, front windows and side windows with a speed greater than or equal to 160km/h:. Its clauses include terms and definitions; test conditions.
Found what you need?
Document preview — GB/T 39709-2020
National Standard of the People's Republic of China
- ICS
- 81.040.01
- Classification
- Q 34
Issued by: State Administration for Market Regulation; Standardization Administration of the PRC
Contents
- Foreword
- 1 Scope
- 2 Normative references
- 3 Terms and definitions
- 4 Test conditions
- 5 Basic principles of the test
- 5:1 Static pressure resistance
- 5:2 Sealing performance
- 6 Test equipment
- 7 Test sample
- 8 Test procedure
- 8:1 Static pressure resistance
- 8:2 Static time constant taustat
- 8:3 Static equivalent leakage hole area
- 9 Test report
- Appendix A (informative appendix) Calculation of air density and local speed of sound
1 Scope
This standard specifies the test conditions, basic principles, test equipment, test equipment,
Test samples, test procedures and test reports:
This standard is applicable to the evaluation of static pressure resistance and sealing performance of EMU glass, front windows and side windows with a speed greater than or equal to 160km/h:
2 Normative references
The following documents are indispensable for the application of this document: For dated reference documents, only the dated version applies to this article
Pieces: For undated references, the latest version (including all amendments) applies to this document:
GB/T 8170 Numerical rounding rules and the expression and determination of limit values
3 Terms and definitions
The following terms and definitions apply to this document:
3:1
Static pressureresistance
The ability of the sample to withstand evenly distributed loads:
3:2
Timeconstant
The ratio of the pressure difference between inside and outside the vehicle to the change in pressure inside the vehicle is expressed by formula (1):
tau = pi-pe()/dpi/dt() (1)
Where:
tau --- time constant in seconds (s);
pi --- the pressure inside the car, the unit is Pa (Pa);
pe --- pressure outside the vehicle, in Pa (Pa);
t --- time, in seconds (s):
3:3
Static time constant statictimeconstant
taustat
The time constant obtained from the static leakage test of the vehicle at a standstill:
Note: The static time constant is numerically equal to the time taken when the pressure difference between inside and outside the vehicle is reduced from the initial value to 1/e of the initial value, e is the natural constant:
4 Test conditions
Except for special requirements, the test should be carried out under the following environmental conditions:
......
This preview omits tables, figures, formulas and parts of the technical clauses. The complete document — 15 pages — is available in the English PDF.
Similar standards
How to Download GB/T 39709-2020
- 1
Add to cart
Click "Download PDF" on this page and choose "Buy this standard". You can add more standards before checkout.
- 2
Checkout
Enter your email and billing details. Payment is processed securely by Stripe (cards or bank transfer). Prefer bank details? Request a quotation (min. order $300).
- 3
Fast delivery
After payment you'll receive an email confirmation. The English PDF is sent to the same address, usually within minutes and at the latest within 1 business day.
- 4
Invoice included
A tax invoice is attached to the confirmation email. Need a custom invoice? Contact us.
Related Standards
GB/T 10003-2026 — Biaxially oriented polypropylene (BOPP) film
GB/T 10004-2026 — Plastic/Plastic laminated films and pouches for packaging
GB/T 10007-2026 — Rigid cellular plastics - Determination of shear properties
GB/T 39709-2020
$150.00